This just adds them to include/linux/Kbuild using header-y.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The struct is part of the userspace interface and can not use
bitfields. This patch replaces the bitfields with a __u32 'control'
word and provides access macros to set the bits.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
[IPSEC]: Add xfrm_sysctl.txt.
[BRIDGE]: Round off STP perodic timers.
[BRIDGE]: Reduce frequency of forwarding cleanup timer in bridge.
[TCP] tcp_probe: use GCC printf attribute
[TCP] tcp_probe: a trivial fix for mismatched number of printl arguments.
[IPV6] ADDRCONF: Fix conflicts in DEVCONF_xxx constant.
[NET] napi: Call __netif_rx_complete in netif_rx_complete
[TCP]: Consolidate checking for tcp orphan count being too big.
[SOCK]: Shrink struct sock by 8 bytes on 64-bit.
[AF_PACKET]: Kill CONFIG_PACKET_SOCKET.
[IPV6]: Fix build warning.
[AF_PACKET]: Kill bogus CONFIG_PACKET_MULTICAST
[IPV4]: Kill references to bogus non-existent CONFIG_IP_NOSIOCRT
[IPSEC]: Fix panic when using inter address familiy IPsec on loopback.
[NET]: parse ip:port strings correctly in in4_pton
[IPV6] ROUTE: No longer handle ::/0 specially.
[IPSEC]: Fix IPv6 AH calculation in outbound
[XFRM]: xfrm_larval_drop sysctl should be __read_mostly.
[XFRM]: Allow XFRM_ACQ_EXPIRES to be tunable via sysctl.
[CASSINI]: Fix printk message typo.
...
Add the basic infrastructure to allow runtime patching of kernel and modules
to optimize a few functions with parameters, which are only calculated once
during bootup and are otherwise constant. Use this for the conversion between
virtual and physical addresses.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch kills a little bit of code duplication between the two
variants of netif_rx_complete.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_out_of_resources() and tcp_close() perform the
same checking of number of orphan sockets. Move this
code into common place.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several errors were spotted during building for custom config (SMP
included). Although SMP still does not compile (no ipi and
__smp_call_function) and does not work, this looks a bit cleaner.
Some other errors obtained via gcc-4.1.0 build.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some of the new syscalls require supporting TIF_RESTORE_SIGMASK.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove 2 functions private to the alpha implemetation,
in favor of similar functions in <linux/log2.h>.
Provide a more efficient version of the fls64 function
for pre-ev67 alphas.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are currently using the ARMv6 operations but need to duplicate some
of the code because of the introduction of the new CPU barrier
instructions in ARMv7.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 has an reset-errata where the clock
may cause a glitch switching back to EXTCLK. We
force a switch to EXTCLK before writing the
reset register to force use of the CLKCON sync
logic to properly switch.
Fix problem reported by Matthieu Castet.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the newly introduced __used attribute in place of the deprecated
__attribute_used__. Functionally the same.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add __init to:
acpi_initialize_subsystem() (and un-export it)
acpi_os_initialize()
Add __initdata to:
acpi_osl_dmi_table[]
Signed-off-by: Len Brown <len.brown@intel.com>
get_next_timer_interrupt() returns a delta of (LONG_MAX > 1) in case
there is no timer pending. On 64 bit machines this results in a
multiplication overflow in tick_nohz_stop_sched_tick().
Reported by: Dave Miller <davem@davemloft.net>
Make the return value a constant and limit the return value to a 32 bit
value.
When the max timeout value is returned, we can safely stop the tick
timer device. The max jiffies delta results in a 12 days timeout for
HZ=1000.
In the long term the get_next_timer_interrupt() code needs to be
reworked to return ktime instead of jiffies, but we have to wait until
the last users of the original NO_IDLE_HZ code are converted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The boot option "acpi_osi=" has always disabled Linux _OSI support,
thus disabling all OS Interface strings which are advertised
by Linux to the BIOS.
Now...
acpi_osi="string" adds the interface string, and
acpi_osi="!string" invalidates the pre-defined interface string
eg. acpi_osi="!Windows 2006"
would disable Linux's claim of Vista compatibility.
Signed-off-by: Len Brown <len.brown@intel.com>
The RO_DATA section were hardcoded to a specific
alignment in include/asm-generic/vmlinux.h.
But for sparc64 this did not match the PAGE_SIZE.
Introduce a new section definition named:
RO_DATA that takes actual alignment as parameter.
RODATA are provided for backward compatibility.
On top of this avoid hardcoding alignment for
sparc64 in reset of the script
Fix is build-tested on sparc64 + x86_64.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Several interfaces were missing and others misnumbered or
improperly documented.
Also, make sure to check the return value when registering
the kernel TSBs with the hypervisor. This helped to find
the 4MB kernel TSB alignment bug fixed in a previous changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) The TSB lookup was not using the correct hash mask.
2) It was not aligned on a boundary equal to it's size,
which is required by the sun4v Hypervisor.
wasn't having it's return value checked, and that bug will be fixed up
as well in a subsequent changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cheetah systems can have cpuids as large as 1023, although physical
systems don't have that many cpus.
Only three limitations existed in the kernel preventing arbitrary
NR_CPUS values:
1) dcache dirty cpu state stored in page->flags on
D-cache aliasing platforms. With some build time
calculations and some build-time BUG checks on
page->flags layout, this one was easily solved.
2) The cheetah XCALL delivery code could only handle
a cpumask with up to 32 cpus set. Some simple looping
logic clears that up too.
3) thread_info->cpu was a u8, easily changed to a u16.
There are a few spots in the kernel that still put NR_CPUS
sized arrays on the kernel stack, but that's not a sparc64
specific problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 got rid of the pagefault notifiers, so the enum value for them
can go away aswell.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ioctls and values needed for this to the ARM26/ARM32 ports. The
actual code has been in the base kernel for a while and automatically turns
on when a port sets the required defines.
[RMK: also added termbits.h changes to avoid build breakage]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This trivial patch updates the nslu2 and nas-100d headers to
remove pointless GPIO defines, and updates nslu2-setup.c
accordingly. In addition minor style cleanups to some comments
are included.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is required as the frequency fixup in nslu2_init does not
run sufficiently early in the boot sequence to take effect. In addition
the dsmg600 setup code behaviour has been improved such that a
'fixup' routine is avoided.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add physical address of HSMMC to include/asm-arm/arch-s3c2410/map.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definitions for S3C2443 functions in GPIOJ
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] acpi_get_sysname() should be __init
[IA64] Cleanup acpi header to reuse the generic _PDC defines
[IA64] Fix using uninitialized data in _PDC setup
[IA64] start_secondary() and smp_callin() should be __cpuinit
1. Add support for decoding IPv6 address. I know it was manually added in
the header file, but not in the template file. That wouldn't work.
2. Add missing support for decoding T.120 address in OLCA.
3. Remove unnecessary decoding of Information signal.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the packet size is changed by the FTP NAT helper, the connection
tracking helper adjusts the sequence number of the newline character
by the size difference. This is wrong because NAT sequence number
adjustment happens after helpers are called, so the unadjusted number
is compared to the already adjusted one.
Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ia64 _PDC setup is defined similar to i386. So, cleanup the header to use
generic _PDC defines than using specific defines in ia64.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change the default printout message for WARN_ON() to say what it is, not
something else. I'm tired of having people get all aflutter about a warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFS: Fix nfs_direct_dirty_pages()
NFS: Fix handful of compiler warnings in direct.c
NFS: Avoid a deadlock situation on write
When processes are allowed to attempt to lock a non-contiguous range of nfs
write requests, it is possible for generic_writepages to 'wrap round' the
address space, and call writepage() on a request that is already locked by
the same process.
We avoid the deadlock by checking if the page index is contiguous with the
list of nfs write requests that is already held in our
nfs_pageio_descriptor prior to attempting to lock a new request.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The L2CAP configuration parameter handling was missing the support
for rejecting unknown options. The capability to reject unknown
options is mandatory since the Bluetooth 1.2 specification. This
patch implements its and also simplifies the parameter parsing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The check (boot_cpu_data.x86 == 3) in atomic_add_return() and
local_add_return() fails, when those operations are used before
boot_cpu_data is filled in.
Change the check to (boot_cpu_data.x86 <= 3) to fix this.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible that real data or metadata follows the bitmap without full page
alignment.
So limit the last write to be only the required number of bytes, rounded up to
the hard sector size of the device.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve Hawkes discovered a problem where recalc_sigpending_tsk was called in
do_sigaction but no signal_wake_up call was made, preventing later signals
from waking up blocked threads with TIF_SIGPENDING already set.
In fact, the few other calls to recalc_sigpending_tsk outside the signals
code are also subject to this problem in other race conditions.
This change makes recalc_sigpending_tsk private to the signals code. It
changes the outside calls, as well as do_sigaction, to use the new
recalc_sigpending_and_wake instead.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: <Steve.Hawkes@motorola.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
include/linux/capability.h:397: warning: "struct task_struct" declared inside parameter list
include/linux/capability.h:397: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send an uevent to user space to indicate that a media change event has
occurred.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow user space to determine if a disk supports Asynchronous Notification of
media changes. This is done by adding a new sysfs file "capability_flags",
which is documented in (insert file name). This sysfs file will export all
disk capabilities flags to user space. We also define a new flag to define
the media change notification capability.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Other than refrigerator, no one else calls frozen_process(). So move it from
include/linux/freezer.h to kernel/power/process.c.
Also, since a task can be marked as frozen by itself, we don't need to pass
the (struct task_struct *p) parameter to frozen_process().
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the race pointed out by Oleg Nesterov.
* Freezer marks a thread as freezeable.
* The thread now marks itself PF_NOFREEZE, but it will be frozen on
on calling try_to_freeze(). Thus the task is frozen, even though it doesn't
want to.
* Subsequent thaw_processes() will also fail to thaw the task since it is
marked PF_NOFREEZE.
Avoid this problem by checking the task's PF_NOFREEZE status in
frozen_processes() before marking the task as frozen.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently try_to_freeze_tasks() has to wait until all of the vforked processes
exit and for this reason every user can make it fail. To fix this problem we
can introduce the additional process flag PF_FREEZER_SKIP to be used by tasks
that do not want to be counted as freezable by the freezer and want to have
TIF_FREEZE set nevertheless. Then, this flag can be set by tasks using
sys_vfork() before they call wait_for_completion(&vfork) and cleared after
they have woken up. After clearing it, the tasks should call try_to_freeze()
as soon as possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the freezing of tasks fails and a task is preempted in refrigerator()
before calling frozen_process(), then thaw_tasks() may run before this task is
frozen. In that case the task will freeze and no one will thaw it.
To fix this race we can call freezing(current) in refrigerator() along with
frozen_process(current) under the task_lock() which also should be taken in
the error path of try_to_freeze_tasks() as well as in thaw_process().
Moreover, if thaw_process() additionally clears TIF_FREEZE for tasks that are
not frozen, we can be sure that all tasks are thawed and there are no pending
"freeze" requests after thaw_tasks() has run.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700.
From: Henry Su <henry.su@amd.com>
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix kmalloc(0) in arch/ia64/pci/pci.c
[IA64] Only unwind non-running tasks.
[IA64] Improve unwind checking.
[IA64] Yet another section mismatch warning
[IA64] Fix bogus messages about system calls not implemented.
Reverted the change to struct v4l2_pix_format. I completely missed that
this struct was used by existing ioctls so that changing it broke the ABI.
I will have to think of another way of setting the top/left coordinates
but for now this change is reverted to preserve compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
commit e8edc6e03a added an include of
linux/jiffies.h in linux/smb_fs.h outside the ifdef __KERNEL__.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: bump versions
libata: Trim trailing whitespace
libata: Kiss post_set_mode goodbye
ata_piix: clean up
pata_hpt366: Enable bits are unreliable so don't use them
libata: Add Seagate STT20000A to DMA blacklist.
ahci: disable 64bit dma on sb600
About a dozen drivers that have some form of crc checksumming or offloading
use this constant, warranting a global define for it.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/cm: Improve local id allocation
IPoIB/cm: Fix SRQ WR leak
IB/ipoib: Fix typos in error messages
IB/mlx4: Check if SRQ is full when posting receive
IB/mlx4: Pass send queue sizes from userspace to kernel
IB/mlx4: Fix check of opcode in mlx4_ib_post_send()
mlx4_core: Fix array overrun in dump_dev_cap_flags()
IB/mlx4: Fix RESET to RESET and RESET to ERROR transitions
IB/mthca: Fix RESET to ERROR transition
IB/mlx4: Set GRH:HopLimit when sending globally routed MADs
IB/mthca: Set GRH:HopLimit when building MLX headers
IB/mlx4: Fix check of max_qp_dest_rdma in modify QP
IB/mthca: Fix use-after-free on device restart
IB/ehca: Return proper error code if register_mr fails
IPoIB: Handle P_Key table reordering
IB/core: Use start_port() and end_port()
IB/core: Add helpers for uncached GID and P_Key searches
IB/ipath: Fix potential deadlock with multicast spinlocks
IB/core: Free umem when mm is already gone
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fix:
mm/slab: fix section mismatch warning
mm: fix section mismatch warnings
init/main: use __init_refok to fix section mismatch
kbuild: introduce __init_refok/__initdata_refok to supress section mismatch warnings
all-archs: consolidate .data section definition in asm-generic
all-archs: consolidate .text section definition in asm-generic
kbuild: add "Section mismatch" warning whitelist for powerpc
kbuild: make better section mismatch reports on i386, arm and mips
kbuild: make modpost section warnings clearer
kconfig: search harder for curses library in check-lxdialog.sh
kbuild: include limits.h in sumversion.c for PATH_MAX
powerpc: Fix the MODALIAS generation in modpost for of devices
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] More verbose show_mem() like other architectures.
[S390] Make use of kretprobe_assert.
[S390] Wire up signald, timerfd and eventfd syscalls.
[S390] Wire up sys_utimensat.
[S390] cio: Update documentation.
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Fix race condition about network device name allocation.
[IPV4]: icmp: fix crash with sysctl_icmp_errors_use_inbound_ifaddr
[NETFILTER]: nf_conntrack_ipv4: fix incorrect #ifdef config name
[NETFILTER]: nf_conntrack: fix use-after-free in helper destroy callback invocation
[IPSEC] pfkey: Load specific algorithm in pfkey_add rather than all
[TCP] FRTO: Prevent state inconsistency in corner cases
[TCP] FRTO: Add missing ECN CWR sending to one of the responses
[NET]: Fix net/core/skbuff.c gcc-3.2.3 compilation error
[RFKILL]: Fix check for correct rfkill allocation
[IPV6]: Add ip6_tunnel.h to headers_install
The ifdef tests were broken. Assume it acts like gcc 4
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) add new processor BF52x/BF54x header files
b) update blackfin BF533/BF537/BF561 header files to latest one in VDSP.
c) scrub watchdog/rtc masks from headers as we dont need/want them (too generic and the drivers dont use them)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Disable Interrupts during DMA memcpy to avoid raise conditions.
2) Mark MDMA channel 0 as reserved, since were using it internally.
3) Add DMA based equivalents for insX and outsX.
4) Our insX and outsX only handles len <= 2^16.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wire up sys_utimensat, reserve syscall number for sys_fallocate and
add a couple of syscalls to the ignore list to get rid of warings.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the irq.h changes went in, the dreamcast code was still
referencing an old value. Switch it back to the IRQ number,
which fixes this:
arch/sh/boards/dreamcast/irq.c: In function `disable_systemasic_irq':
arch/sh/boards/dreamcast/irq.c:59: error: `OFFCHIP_IRQ_BASE' undeclared (first
use in this function)
arch/sh/boards/dreamcast/irq.c:59: error: (Each undeclared identifier is reported only once
arch/sh/boards/dreamcast/irq.c:59: error: for each function it appears in.)
Reported-by: Adrian McMenamin <adrian@newgolddream.dyndns.info>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just at the time you added them on sh we're removing them from other
architectures. As there's no user yet this patch just removes them
completely. Once you actually have a kprobes patch it should follow
the direct call to kprobes_fault_handler model that powerpc, s390 and
sparc64 employ in 2.6.22-rc1 and that I'm updating other architectures
to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add definition for high-speed MMC/SD device and add to SMDK2443
device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the name of the S3C2443_SDI1 to S3C2443_HSMMC to ensure
that it is correctly identified.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need valid_phys_addr_range() or valid_mmap_phys_addr_range()
for the !CONFIG_MMU case.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Mobile IPv6 package (http://www.mobile-ipv6.org/software/) needs
this header file to build the tunnelctl component. The header
already looks sanitized so is safe to export.
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ib_find_gid() and ib_find_pkey() functions that use uncached device
queries. The calls might block but the returns are always up-to-date.
Cache P_Key and GID table lengths in core to avoid extra port info queries.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Throughout the kernel there are a few legitimite references
to init or exit sections. Most of these are covered by the
patterns included in modpost but a few nees special attention.
To avoid hardcoding a lot of function names in modpost introduce
a marker so relevant function/data can be marked.
When modpost see a reference to a init/exit function from
a function/data marked no warning will be issued.
Idea from: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
1 is a power of two, therefore roundup_pow_of_two(1) should return 1. It does
in case the argument is a variable but in case it's a constant it behaves
wrong and returns 0. Probably nobody ever did it so this was never noticed.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are seven legacy system calls that ia64 doesn't implement, but glibc
provides equivalent functionality by using more modern system calls. Stop
checksyscalls.sh from complaining about these seven.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (32 commits)
[POWERPC] Remove build warnings in windfarm_core
[POWERPC] Pass per-file CFLAGs for platform specific op codes
[POWERPC] Correct #endif comment
[POWERPC] Fix ppc_rtas_progress_show()
[POWERPC] Fix sed command lines for zlib source construction
[POWERPC] Specify GNUTARGET on $(AR) invocations
[POWERPC] Make sure device node type/name is not NULL on hot-added nodes
[POWERPC] Small fixes for the Ebony device tree
[POWERPC] Fix warning on UP
[POWERPC] cell_defconfig: Disable cpufreq and pmi
[POWERPC] Fix IO space on PCI buses created from of_platform
[POWERPC] Add spinlock to request_phb_iospace()
[POWERPC] Fix make rules for treeImage.initrd
[POWERPC] Remove warning in mpic.c
[POWERPC] Update pasemi_defconfig
[POWERPC] pasemi: CONFIG_GENERIC_TBSYNC no longer needed
[POWERPC] Update iseries_defconfig
[POWERPC] Wire up some more syscalls
[POWERPC] Fix bug adding properties with flatdevtree.c's ft_set_prop()
[POWERPC] Remove fixup_bigphys_addr() for arch/powerpc to avoid link error
...
As pointed out by Jarek Poplawski, the patch
[WORKQUEUE]: cancel_delayed_work: use del_timer() instead of del_timer_sync()
commit: 071b638689
was wrong, it was merged by mistake after that.
From the changelog:
after this patch:
...
delayed_work_timer_fn->__queue_work() in progress.
The latter doesn't differ from the caller's POV,
it does make a difference if the caller calls flush_workqueue() after
cancel_delayed_work(), in that case flush_workqueue() can miss this
work_struct.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jarek Poplawski <jarkao2@o2.pl>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Re-introduce rmap verification patches that Hugh removed when he removed
PG_map_lock. PG_map_lock actually isn't needed to synchronise access to
anonymous pages, because PG_locked and PTL together already do.
These checks were important in discovering and fixing a rare rmap corruption
in SLES9.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sysctl/kernel/core_pattern and fs/exec.c agree on maximum core
filename size and change it to 128, so that extensive patterns such as
'/local/cores/%e-%h-%s-%t-%p.core' won't result in truncated filename
generation.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.
[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a known fact that freezeable multithreaded workqueues doesn't like
CPU_DEAD. We keep them only for the incoming CPU-hotplug rework.
Sadly, we can't just kill create_freezeable_workqueue() right now, make
them singlethread.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures that have an implementation of smp_call_function_single
let it return -EBUSY if it is asked to execute func on the current cpu.
(akpm: except for x86_64). Therefore the UP version must always return
-EBUSY.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures. Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.
This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.
In particular, on x86_64, __node_distance calls node_to_pxm().
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have a maze of configuration variables that determine the
maximum slab size. Worst of all it seems to vary between SLAB and SLUB.
So define a common maximum size for kmalloc. For conveniences sake we use
the maximum size ever supported which is 32 MB. We limit the maximum size
to a lower limit if MAX_ORDER does not allow such large allocations.
For many architectures this patch will have the effect of adding large
kmalloc sizes. x86_64 adds 5 new kmalloc sizes. So a small amount of
memory will be needed for these caches (contemporary SLAB has dynamically
sizeable node and cpu structure so the waste is less than in the past)
Most architectures will then be able to allocate object with sizes up to
MAX_ORDER. We have had repeated breakage (in fact whenever we doubled the
number of supported processors) on IA64 because one or the other struct
grew beyond what the slab allocators supported. This will avoid future
issues and f.e. avoid fixes for 2k and 4k cpu support.
CONFIG_LARGE_ALLOCS is no longer necessary so drop it.
It fixes sparc64 with SLAB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm getting zillions of undefined references to __kmalloc_size_too_large on
alpha. For some reason alpha is building out-of-line copies of kmalloc_slab()
into lots of compilation units.
It turns out that gcc just isn't smart enough to work out that
__builtin_contant_p(size)==true implies that __builtin_contant_p(index)==true.
So let's give it a bit of help.
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two definitions remained in slab.h that are particular to the SLAB allocator.
Move to slab_def.h
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no user of destructors left. There is no reason why we should keep
checking for destructors calls in the slab allocators.
The RFC for this patch was discussed at
http://marc.info/?l=linux-kernel&m=117882364330705&w=2
Destructors were mainly used for list management which required them to take a
spinlock. Taking a spinlock in a destructor is a bit risky since the slab
allocators may run the destructors anytime they decide a slab is no longer
needed.
Patch drops destructor support. Any attempt to use a destructor will BUG().
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no actual implementations of fixup_bigphys_addr() in
arch/powerpc, and with a 64-bit aware ioremap() and so forth, it
should no longer be necessary. This patch removes the last dregs of
fixup_bigphys_addr() from arch/powerpc.
In fact, the only reason this hasn't caused link errors already is
that nobody must have tried using one of the small number of drivers
using io_remap_pfn_range() on one of the small number of platforms
which are 32-bit but define CONFIG_PHYS_64BIT. Nonetheless this fixes
a bug, and should go into 2.6.22.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove CPU_FTR_NEED_COHERENT for MPC7448 (and single-core MPC86xx).
This prevents needlessly setting M=1 when not SMP.
Signed-off-by: James.Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change several headers in include/asm-powerpc that currently use some variation
of ASM_PPC to use ASM_POWERPC instead.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Presently, we check for the minimum ARM architecture that we're
building for to determine whether we need ASID support. This is
wrong - if we're going to support a range of CPUs which include
ARMv6 or higher, we need the ASID.
Convert the checks to use a new configuration symbol, and arrange
for ARMv6 and higher CPU entries to select it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: track spindown status and skip spindown_compat if possible
libata: fix shutdown warning message printing
libata-acpi: add ATA_FLAG_ACPI_SATA port flag
libata: during revalidation, check n_sectors after device is configured
libata: separate out ata_dev_reread_id()
pata_scc had been missed by ata_std_prereset() switch
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa:
[ALSA] usbaudio - Coping with short replies in usbmixer
[ALSA] Include quirks from Ubuntu Dapper/Edgy/Feisty
[ALSA] Fix probe of non-PnP ISA devices
[ALSA] version 1.0.14rc4
[ALSA] hda-codec - Fix ALC882/861VD codec support on some laptops
[ALSA] ASoC AC97 device reg bugfix
[ALSA] ASoC AC97 static GPL symbol fix
[ALSA] hda-codec - Make the mixer capability check more robust
[ALSA] usb-audio: another Logitech QuickCam ID
Sorry I screwed up the comparison. It is only an error if we attempt
to allocate a slab larger than the maximum allowed size.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of the notifier list and call the kprobes code directly
if compiled in. This mirrors the changes that recently went
into powerpc, s390 and sparc64.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add utimensat, signalfd, timerfd, eventfd syscalls. Add ignore
defines for sync_file_range and fadvise64_64 which we implement
differently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the SPI Channel 1 register offset in s3c_spi1_resource[], and
s3c2412_dma_mappings[]. Offset has to be 0x100 in s3c2412/13's case.
Also, total SPI memory resource size changed to 0x24 for s3c2412/13.
Signed-off-by: Sandeep Patil <psandeep.s@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Integrator/CP SMP platform support was never fully merged, and now
it's causing build breakage. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a bug whereby AC97 bus device data was being clobbered
when AC97 codecs using the generic ac97_codec.c driver were being
registered. Codecs that didn't use the generic driver were unaffected
(e.g. WM9712, WM9713).
Changes:-
o Add new AC97 codec class for custom (or need bus dev registration)
AC97 codecs.
o Only register/deregister this custom codec device with the AC97 bus.
The generic AC97 driver already does this for generic codec devices.
This may be related to bug #3038 :-
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3038
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Our assumption that most distros issue STANDBYNOW seems wrong. The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown. We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whether a controller needs IDE or SATA ACPI hierarchy is determined by
the programming interface of the controller not by whether the
controller is SATA or PATA, or it supports slave device or not. This
patch adds ATA_FLAG_ACPI_SATA port flags which tells libata-acpi that
the port needs SATA ACPI nodes, and sets the flag for ahci and
sata_sil24.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Device might be resized during ata_dev_configure() due to HPA or
(later) ACPI _GTF. Currently it's worked around by caching n_sectors
before turning off HPA. The cached original size is overwritten if
the device is reconfigured without being hardreset - which always
happens after configuring trasnfer mode. If the device gets hardreset
for some reason after that, revalidation fails with -ENODEV.
This patch makes size checking more robust by moving n_sectors check
from ata_dev_reread_id() to ata_dev_revalidate() after the device is
fully configured. No matter what happens during configuration, a
device must have the same n_sectors after fully configured to be
treated as the same device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably. So add a small set of interfaces
to request API versions and query current settings.
This allows us to fix some bugs in the hypervisor console:
1) If we can negotiate API group CORE of at least major 1
minor 1 we can use con_read and con_write which can improve
console performance quite a bit.
2) When we do a console write request, we should hold the
spinlock around the whole request, not a byte at a time.
What would happen is that it's easy for output from
different cpus to get mixed with each other.
3) Use consistent udelay() based polling, udelay(1) each
loop with a limit of 1000 polls to handle stuck hypervisor
console.
Signed-off-by: David S. Miller <davem@davemloft.net>
it depends on elimination of unreachable branches in switch (by object
size), so we must declare it always_inline
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
Use menuconfig objects: IDE
sl82c105: Switch to ref counting API
ide: remove ide_use_dma()
ide: add missing validity checks for identify words 62 and 63
ide: remove ide_dma_enable()
sl82c105: add speedproc() method and MWDMA0/1 support
cs5530/sc1200: add ->speedproc support
cs5530/sc1200: DMA support cleanup
ide: use ide_tune_dma() part #2
cs5530/sc1200: add ->udma_filter methods
ide: always disable DMA before tuning it
pdc202xx_new: use ide_tune_dma()
alim15x3: use ide_tune_dma()
sis5513: PIO mode setup fixes
serverworks: PIO mode setup fixes
pdc202xx_old: rewrite mode programming code (v2)
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Take MAX_ORDER into consideration when determining KMALLOC_SHIFT_HIGH.
Otherwise we may run into a situation where we attempt to create general
slabs larger than MAX_ORDER.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several parts of kernel/smp.c and smpboot.c are generally useful for other
subarchitectures and paravirt_ops implementations, so make them available for
reuse.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After examining what was checked in and the code base I discovered that most
of 86c0baf123 wasn't necessary anymore....
So here's a patch that reverts the last part of that changeset:
Revert part of 86c0baf123.
The kernel has moved forward to a state where the original change is not
necessary. After porting forward, this final version of the patch was
applied and broke non-x86 architectures.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
