Move network device exit batching from a special case in
net_namespace.c to using common mechanisms in dev.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add exit_list to struct net to support building lists of network
namespaces to cleanup.
- Add exit_batch to pernet_operations to allow running operations only
once during a network namespace exit. Instead of once per network
namespace.
- Factor opt ops_exit_list and ops_exit_free so the logic with cleanup
up a network namespace does not need to be duplicated.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8ec1e0ebe26087bfc5c0394ada5feb5758014fc8
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:16:35 2009 +0100
ipv4: add sysctl to accept packets with local source addresses
Change fib_validate_source() to accept packets with a local source address when
the "accept_local" sysctl is set for the incoming inet device. Combined with the
previous patches, this allows to communicate between multiple local interfaces
over the wire.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d124356ce314fff22a047ea334379d5105b2d834
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:16:35 2009 +0100
net: fib_rules: allow to delete local rule
Allow to delete the local rule and recreate it with a higher priority. This
can be used to force packets with a local destination out on the wire instead
of routing them to loopback. Additionally this patch allows to recreate rules
with a priority of 0.
Combined with the previous patch to allow oif classification, a socket can
be bound to the desired interface and packets routed to the wire like this:
# move local rule to lower priority
ip rule add pref 1000 lookup local
ip rule del pref 0
# route packets of sockets bound to eth0 to the wire independant
# of the destination address
ip rule add pref 100 oif eth0 lookup 100
ip route add default dev eth0 table 100
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 68144d350f4f6c348659c825cde6a82b34c27a91
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:05:25 2009 +0100
net: fib_rules: add oif classification
Support routing table lookup based on the flow's oif. This is useful to
classify packets originating from sockets bound to interfaces differently.
The route cache already includes the oif and needs no changes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 229e77eec406ad68662f18e49fda8b5d366768c5
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:05:23 2009 +0100
net: fib_rules: rename ifindex/ifname/FRA_IFNAME to iifindex/iifname/FRA_IIFNAME
The next patch will add oif classification, rename interface related members
and attributes to reflect that they're used for iif classification.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b8952893d5d86f69c4e499d191b98c6658f64b0f
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:05:22 2009 +0100
net: fib_rules: rearrange struct fib_rule
The ifname member is only used to resolve interface names and is not needed
during rule lookups. The target and ctarget members however are used during
rule lookups and are currently located in a second cacheline.
Move ifname further to the end to make sure both target and ctarget are
located in the same cacheline as other members used during rule lookups.
The layout on 64 bit changes from:
struct fib_rule {
...
u32 table; /* 56 4 */
u8 action; /* 60 1 */
/* XXX 3 bytes hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
u32 target; /* 64 4 */
/* XXX 4 bytes hole, try to pack */
struct fib_rule * ctarget; /* 72 8 */
struct rcu_head rcu; /* 80 16 */
struct net * fr_net; /* 96 8 */
};
to:
struct fib_rule {
...
u32 table; /* 40 4 */
u8 action; /* 44 1 */
/* XXX 3 bytes hole, try to pack */
u32 target; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
struct fib_rule * ctarget; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
char ifname[16]; /* 64 16 */
struct rcu_head rcu; /* 80 16 */
struct net * fr_net; /* 96 8 */
};
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If running in non-secure mode accessing
some registers of l2x0 will fault. So
check if l2x0 is already enabled, if so
do not access those secure registers.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
removed old macro definition for io access, using
the generic macros defined in asm/io.h
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ahci can drive the Promise PDC42819, but obviously it can only use SATA
disks connected to this controller. The controller can actually support
SAS disks as well, but we only know how to use it in it's AHCI mode.
Add a message to let users know that because ahci is driving their chip
they can only use the SATA disks connected to this controller.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x. Fix it and reformat the comment, while at it.
Bump the driver version, accounting for several patches that forgot to do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes. Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...
However, the drivers added some breakage of their own too: the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...
Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
By default the RFCOMM layer would still use L2CAP basic mode. For testing
purposes this option enables RFCOMM to select enhanced retransmission
mode.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auto sleep mode for btmrvl driver is not enabled by default.
This patch enables auto sleep mode when card is probed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SendRRorRNR needs to acknowledge received I-frames (actually every packet
needs to acknowledge received I-frames by sending the proper packet
sequence number), so ReqSeq is set to the next I-frame number sequence to
be pulled by the reassembly function.
SendRRorRNR tells the remote side about local busy conditions, it sends
a Receiver Ready frame if local busy is false or a Receiver Not Ready
if local busy is true.
ReqSeq is the packet's field to send the number of the acknowledged
packets.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RejActioned is used to prevent retransmission when a entity is on the
WAIT_F state, i.e., waiting for a frame with F-bit set due local busy
condition or a expired retransmission timer. (When these two events raise
they send a frame with the Poll bit set and enters in the WAIT_F state to
wait for a frame with the Final bit set.)
The local entity doesn't send I-frames(the data frames) until the receipt
of a frame with F-bit set. When that happens it also set RejActioned to false.
RejActioned is a mandatory feature of ERTM spec.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As specified by ERTM spec an ERTM channel can acknowledge received
I-frames(the data frames) by sending an I-frame with the proper ReqSeq
value (i.e. ReqSeq is set to BufferSeq). Until now we aren't setting the
ReqSeq value on I-frame control bits. That way we can save sending
S-frames(Supervise frames) only to acknowledge receipt of I-frames. It
is very helpful to the full-duplex channel.
ReqSeq is the packet sequence number sent in an acknowledgement frame to
acknowledge receipt of frames up to (ReqSeq - 1).
BufferSeq controls the receiver buffer, it is used to delay
acknowledgement of new frames to not cause buffer overflow. BufferSeq
value is not increased until frames are pulled by reassembly function.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SrejActioned is a flag that when set prevents local side to retransmit a
I-frame(the data frame) already retransmitted. The local entity can
retransmit again only when it receives a SREJ frame with the F-bit set.
SREJ frame - Selective Reject frame - is sent when an entity wants the
retransmission of a specific I-frame that was lost or corrupted.
This bug can put ERTM in an unknown state once the entity can't
retransmit.
A frame with the Final bit set is expected when the local side sends a
frame with the Poll bit set due to a local busy condition or a
retransmission timer expired. (Receipt of P-bit shall always be replied by
a frame with the F-bit set).
pi->conn_state keeps informations about many ERTM flags including
SrejActioned.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix ERTM's full-duplex channel to work as specified by ERTM spec. ERTM
needs to handle state vars, timers and counters to send and receive
I-frames(the data frames), i.e., for both sides of data communication.
We initialize all of them to the default values here.
Full-duplex channel is a mandatory feature of ERTM spec.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to BNEP test specification the proper response should be sent
for a setup connection request message after the BNEP connection setup
has been completed.
Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The tasklet schedule function helpers are just an obfuscation. So remove
them and call the schedule functions directly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For future simplification it is important that the hci_recv_frame
function is no longer an inline function. So move it into the module
itself and export it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending commands to a down interface results in a timeout while clearly
it should just return ENETDOWN. When using the ioctls this works fine,
but not when using the HCI sockets sendmsg interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement raw output callback which is used by hidraw to send raw data to
the underlying device.
Without this patch, the userspace hidraw-based applications can't send
output reports to HID Bluetooth devices.
Reported-and-tested-by: Brian Gunn <bgunn@solekai.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The /dev/vhci ops don't refer to the module and so it is possible to
unload the module while the file descriptor is in use. This was an
accidental removal after the cleanup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After the removal of the module parameter for setting the minor number,
this variable became unused. So just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the empty ioctl which just returns -EINVAL. vfs_ioctl() will
return -ENOTTY instead, but I doubt that any application will notice
the difference :)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
o rq_noidle() is supposed to tell cfq that do not expect a request after this
one, hence don't idle. But this does not seem to work very well. For example
for direct random readers, rq_noidle = 1 but there is next request coming
after this. Not idling, leads to a group not getting its share even if
group_isolation=1.
o The right solution for this issue is to scan the higher layers and set
right flag (WRITE_SYNC or WRITE_ODIRECT). For the time being, this single
line fix helps. This should not have any significant impact when we are
not using cgroups. I will later figure out IO paths in higher layer and
fix it.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o If a group is running only a random reader, then it will not have enough
traffic to keep disk busy and we will reduce overall throughput. This
should result in better latencies for random reader though. If we don't
idle on random reader service tree, then this random reader will experience
large latencies if there are other groups present in system with sequential
readers running in these.
o One solution suggested by corrado is that by default keep the random readers
or sync-noidle workload in root group so that during one dispatch round
we idle only once on sync-noidle tree. This means that all the sync-idle
workload queues will be in their respective group and we will see service
differentiation in those but not on sync-noidle workload.
o Provide a tunable group_isolation. If set, this will make sure that even
sync-noidle queues go in their respective group and we wait on these. This
provides stronger isolation between groups but at the expense of throughput
if group does not have enough traffic to keep the disk busy.
o By default group_isolation = 0
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Async queues are not per group. Instead these are system wide and maintained
in root group. Hence their workload slice length should be calculated
based on total number of queues in the system and not just queues in the
root group.
o As root group's default weight is 1000, make sure to charge async queue
more in terms of vtime so that it does not get more time on disk because
root group has higher weight.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o If a queue consumes its slice and then gets deleted from service tree, its
associated group will also get deleted from service tree if this was the
only queue in the group. That will make group loose its share.
o For the queues on which we have idling on and if these have used their
slice, wait a bit for these queues to get backlogged again and then
expire these queues so that group does not loose its share.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o If a task changes cgroup, drop reference to the cfqq associated with io
context and set cfqq pointer stored in ioc to NULL so that upon next request
arrival we will allocate a new queue in new group.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Do not allow following three operations across groups for isolation.
- selection of co-operating queues
- preemtpions across groups
- request merging across groups.
o Async queues are currently global and not per group. Allow preemption of
an async queue if a sync queue in other group gets backlogged.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Export disk time and sector used by a group to user space through cgroup
interface.
o Also export a "dequeue" interface to cgroup which keeps track of how many
a times a group was deleted from service tree. Helps in debugging.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o One can choose to change elevator or delete a cgroup. Implement group
reference counting so that both elevator exit and cgroup deletion can
take place gracefully.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Nauman Rafique <nauman@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
