When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.
if (priv->ieee->wpa_enabled &&
network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does two things. It uses the parameter IW_QUAL_DBM which is new
in WE-19 to cause signal level and noise to be reported in dBm by the
wireless tools. It also defines the signal level as an unsigned integer
so that the signal level will be reported by iwlist iface scan.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace ipw2200 specific frame_hdr_len() with generic
ieee80211 routine ieee80211_get_hdrlen()
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch roll back the change we made to support for the ability to
start/stop independent Tx queues within a single net device in order to
support 802.11e QoS. We need to be able to indicate to the upper layers
that packets of a given priority can not be sent any more without halting
transmission of all packets, and without rescheduling high priority packets
down to the next priority level.
So we return NETDEV_TX_BUSY in this case and rely on the stack would
take care of rescheduling... which it apparently does immediately and
consumes the CPU. This caused the ksoftirqd kernel thread consuming almost
all the CPU...
To put the code back to the way it was before we made these changes we
put the call netif_queue_stop back in ipw_tx_skb. This effectively
disables multiple priority based transmit queues for 802.11e, but given
that its broken anyway...
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Given the amount of support requests for the meaning of the geography code
I've written a patch for printing this information on module load no matter
the debug level.
I've also added a section to the README.ipw2200 file listing the geography
codes and their meaning.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global function ipw_qos_current_mode()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As stated in a comment, the ipw2200 driver uses several routines that
were borrowed from ieee80211_geo.c. As ipw2200 requires ieee80211,
these routines are duplicated. The attached patch, which is sent
as an attachment to preserve whitespace, converts ipw2200.c to use
the ieee80211 versions, thereby reducing bloat in both the source
and binary.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spidernet drivers uses request_firmware() and thus needs to select
FW_LOADER.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adrian Bunk wrote:
> The Coverity checker spotted the following two array overflows in
> drivers/net/chelsio/sge.c (in both cases, the arrays contain 3
> elements):
[snip]
This is a bug. The array should contain 2 elements. Here is the fix.
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
return -E_NO_BIG_ENDIAN_TESTING;
[E1000]: Fix 4 missed endianness conversions on RX descriptor fields.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olaf Hering reported a problem on pseries with e100 where ethtool -t would
cause a bus error, and the e100 driver would stop working. Due to the new
load ucode command the cb list must be allocated before calling
e100_init_hw, so remove the call and just let e100_up take care of it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This patch moves prototypes of global variables and functions to a header
file.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: John Ronciak <john.ronciak@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're leaking an skb in a failure path in this function.
Coverity #632
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted these two unused variables.
Please check whether this patch is correct or whether they should be
used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o Make sgiseeq_dump_rings static.
o Delete unused sgiseeq_my_reset.
o Move DEBUG define to beginning where it's easier to spot and will be
seen by <linux/kernel.h> as well.
o Use NULL for pointer initialization.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert 3c509 driver to use proper suspend/resume API instead of the
deprecated pm_register/pm_unregister.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following possible updates:
- let FORCEDETH no longer depend on EXPERIMENTAL
- remove the "Reverse Engineered" from the option text:
for the user it's important which hardware the driver supports, not
how it was developed
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In latest -mm de620 gave following warning:
WARNING: drivers/net/de620.o - Section mismatch: reference to \
.init.text:de620_probe from .text between 'init_module' (at offset \
0x1682) and 'cleanup_module'
init_module() call de620_probe() which is declared __init.
Fix is to declare init_module() __init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve reference to PCI NE2K support in ISA NE2K documentation.
Original 2.4 patch From: Ged Haywood <ged@jubileegroup.co.uk>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes an error in the dl2k driver's DMA mapping/unmapping.
The adapter uses the upper 16bits of the DMA address for the buffer
size. However, this is not masked off when referencing the DMA
address, and can lead to errors by trying to free a DMA address out of
range.
Thanks,
Jon
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For some reason, E1000's ->hard_start_xmit() routine returns -EFAULT
instead of one of the NETDEV_TX_* error codes. In fact, it frees up
the SKB before returning this. This makes the queueing layer think
the packet should be requeued and subsequently we corrupt a freed
object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turn on truncation to prevent getting choked by frames larger than expected.
Without this fix, driver hangs after receiving an oversize packet.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Avoid premature transmit ring full conditions.
Force a transmit status interrupt if transmit ring gets nearly full
and after a TSO send.
Allow more entries in transmit ring to be used if dma_addr is 32 bits
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Don't use sky2 to seed random pool beacause the network packet arrival time
will not be truly random due to NAPI and interrupt mitigation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
de_init_hw enables the irq thus it must be issued after request_irq.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Paul Rolland reported that e1000 was having a hard time using mii-tool to set speed and duplex. This patch fixes the issue on both newer hardware as well as fixing the code issue that originally caused the problem.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memset() is called before check.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checking e100.c code against Documentation/io_ordering.txt I found the
following problem:
spin_lock_irq...
write
spin-unlock
e100_write_flush
The attached patch fix the code like this:
spin_lock_irq...
write
e100_write_flush
spin-unlock
Signed-off-by: Catalin BOIE <catab@umbrella.ro>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As documented in National application note 1287 the RX state machine on
the natsemi chip can lock up under some conditions (mostly related to
heavy load). When this happens a series of bogus packets are reported
by the chip including some oversized frames prior to the final lockup.
This patch implements the fix from the application note: when an
oversized packet is reported it resets the RX state machine, dropping
any currently pending packets.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts the natsemi driver to use NAPI. It was originally
based on one written by Harald Welte, though it has since been modified
quite a bit, most extensively in order to remove the ability to disable
NAPI since none of the other drivers seem to provide that functionality
any more.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mac_addr variable doesn't get reset between
(re)additions of multicast addresses. One byte
of all multicast addresses (except the first)
can be incorrect.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This documentation is mostly obsolete, and should therefore either be
updated or removed (this patch does the latter).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds support for the 4th port and other new features of the
BCM1480 SOC.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that the BIT0-BIT31 defines are no longer used by mv643xx_eth.c,
remove them from mv643xx_eth.h.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The task level rx queue refill feature hasn't ever worked
(at least in 2.6) and is of dubious value. Remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify and remove redundant code for filling transmit descriptors.
No changes in features; it's just a code reorganization/cleanup.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>From : Dale Farnsworth <dale@farnsworth.org>
Recent patches for the mv643xx_eth driver now use the MII interface
library. Select MII so it gets built when that driver is selected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use better terminology for HW queues. No functional changes.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- this implementation of prefetch was tested on new and old hardware
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Add restriction for ESB2 to MTU size <=9216
- Removed FIFO errors which were not being used
- Fixed issues with loopback
- Power management change for saving state and config space
- WA to disable recieves and reset device on link loss. Reset needed to be done outside the interrupt context - modified existing tx_timeout_task
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Simplified by calling skb_fill_page_desc(), which is more efficient.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
The axnet_cs driver can support the AMB8110 PC Card, so add the id for it.
In the old pcmcia-cs config file, this card is listed with the comment "not
specific enough". The last entry in the axnet_ids has the same comment.
They are disabled, and for good reason as it was originally identified by
the MANFID, and that is shared with several cards that use both the
pcnet_cs driver and axnet_cs driver. I tried my AMB8110 with pcnet_cs, and
found that it works fine, and I cannot find a reason for either, except
that the old config file recommended axnet_cs.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't just use cards with PCMCIA ID 0x0156, 0x0002. Make sure that the
vendor string is "Intersil" or "INTERSIL"
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A recent patch attempted to enable more efficient memory usage by using
only 2kB descriptors for jumbo frames. The method used to implement this
has since been commented upon as "illegal" and in recent kernels even
causes a BUG when receiving ip fragments while using jumbo frames.
This patch simply goes back to the way things were. We expect some
complaints due to order 3 allocations failing to come back due to this
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.
In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These messages end up polluting logs when things like NetworkManager or
wpa_supplicant are controlling the driver. They aren't really that
useful, and no other drivers output messages like this when the user
fiddles with encryption keys. Users can use iwconfig and other
wireless-tools methods to determine and change the current transmit key
if they wish to do so manually. Therefore, remove the messages.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- check that the device is up before it is enabled again;
- the descriptor ring indexes must be set to zero before
cp_init_hw() is issued. Add a nice comment to remember
that skb allocation failure is still not handled.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5681
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
velocity_rx_refill() only replenishes the descriptor entries which
belong to the CPU. It works great in the Rx path but the driver must
ensure that all the descriptors are freed before velocity_rx_refill()
is used in velocity_change_mtu(). The patch resets the Rx descriptors
in velocity_free_rd_ring().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two bugs in the WoL implementation of sis900. The first causes
hangs on some system on driver load, the second causes troubles
when disabling WoL support. Both fixes are one liner and really
simple.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Daniele Venzano <venza@brownhat.org>
drivers/net/tlan.c compiles with CONFIG_PCI=n only with a warning and
due to the dead code elimination of gcc.
Additionally, this fixes the only compile error I found with
CONFIG_PCI=n and the gcc -Werror-implicit-function-declaration
flag on i386.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The most usable number of ifb devices is 2. Change the default to 2.
Signed-off-by: Richard Lucassen <spamtrap@lucassen.org>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between updating the irq mask and setting it
which can be triggered on SMP with a bad cable.
Similar patch from Ingo Molnar and Thomas Gleixner
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The SysKonnect Genesis based board would fail on initialization
with phy_read errors caused by not waiting for last phy write.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Fix a race in the receive NAPI, irq handling. The interrupt clear and the
start need to be separated. Otherwise there is a window between the last
frame received and the NAPI done level handling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
rtl8169_hw_start() requires that the descriptor ring indexes be
set to zero. Let a deferred invocation of rtl8169_reset_task()
handle it. Enabling a few power management bits will not hurt
either.
suspend/resume is issued with irq on: the spinlock do not need
to save the irq flag.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Need to avoid race in updating IRQ mask. This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.
I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to force a transmit coalesce timer restart after processing
transmit packets. Otherwise, can get transmit status after last
update and chip doesn't send the next one.
Can go with the chip defaults for coalescing timers, except for
Tx timer which needs to be bigger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to restart the interrupt coalescing timer after clearing the interrupt,
to avoid races with interrupt timer and processing.
Patch from Carl-Daniel Halfinger
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Don't allow coalescing values to be bigger than the transmit ring.
Since if you set them that big, the interrupt never happens and driver
livelocks.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The following message will be only printed if DEBUG_NOTIF is on. "Unknown
notification: subtype=40,flags=0xa0,size=40"
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This forcedeth patch adds support for MSI/MSIX interrupts.
Signed-off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This forcedeth patch adds high dma support for tx/rx rings.
Signed-off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This forcedeth patch adds support for vlan stripping/inserting in hardware.
Signed-off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes 2 bugs in the USB-IrDA code.
The first one is a buffer overrun in the RX path. We are now using
IRDA_SKB_MAX_MTU when initializing the Rx URB.
The second one is a potential stack recursion when unplugging the USB
dongle. It seems that first we get the Rx URB with a generic error
code, and after a while the Rx URB comes again with a "disconnect"
error code. Since we are resubmitting the Rx URB immediately after
receiving the first error one, we might enter an endless loop.
When getting an error Rx URB, the patch defers the Rx URB resubmitting
so that it gives us a chance to catch the disconnect one, in case the
dongle has juts been unplugged.
Tested against 2.6.16-rc2.
Patch from Jean Tourrilhes
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_release returns EINVAL without releasing the bond lock if the
slave device is not being bonded by the bond. The following patch
ensures that the lock is released in this case.
Signed-off-by: Stephen J. Bevan <stephen@dino.dnsalias.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/tokenring/smctr.c: In function `smctr_load_firmware':
drivers/net/tokenring/smctr.c:2981: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Users report problems w/ auto-negotiation disabled and the link set
to 100/Half or 10/Half. Problems range from poor performance to no
link at all.
The current sky2 code does not set things properly on link up if
autonegotiation is disabled. Plus it does not contemplate a 10Mbit
setting at all. This patch corrects that.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is a clone of John Linville's fixed for speed setting on sky2 driver.
The skge driver has the same code (and bug). It would not allow manually forcing
100 and 10 mbit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Take the experimental dependency of skge driver, it is as stable as the
others.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sk98lin driver was changed a while ago to remove support for the
D-Link 530T card because that hardware has no working VPD data. The help
text for Kconfig was not updated.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some bitfields were incorrectly initialised in wavelan_cs,
causing some compiler warning. Also killed a error message that should
not be there...
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previous patch that added ENCODEEXT and AUTH support to the airo
driver contained a slight error which would cause setting the TX
key index ignore a valid key-set request at the same time. This patch
allows any combination of setting the TX key index and setting an
encryption key.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We didn't set the WEP key to hardware when we are using software based
crypto. Hardware needs the key to do WEP authentication even for
software based encryption.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects a few spelling and grammar errors found in
drivers/net
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not avoid APs with wpa_ie or rsn_ie if !ieee->wpa_enabled
There are broken APs out there that fill these elements even
though encryption is disnabled. Also, this breaks legit WEP to
WPA migration scenarious.
We add a checking to prohibite WPA configured STA trying to
associate with non-WPA supported APs.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I have made a stupid copy&paste error: QoS option is named IPW_QOS not
IPW2200_MONITOR. Spotted by Daniel Paschka, thanks.
Add the following config entries for the ipw2200 driver to
drivers/net/wireless/Kconfig
* IPW2200_MONITOR
enables Monitor mode
* IPW_QOS
enables QoS feature - this is under development right now, so it depends
upon EXPERIMENTAL
Signed-off-by: Andreas Happe <andreashappe@snikt.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the Atmel driver-only IEEE 802.11 constants to their
equivalents from the kernel's ieee80211 layer headers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the IPW2100 and IPW2200 options available in
the configuration menu even if IEEE80211 has not been selected before.
This behaviour is more intuitive for people which are not familiar with
the driver internals.
The suggestion for this change was made by Alejandro Bonilla Beeche.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a number of bugs in the authentication process:
1) When falling back to Shared Key authentication mode from Open System,
a missing 'return' would cause the auth request to be sent, but would
drop the card into Management Error state. When falling back, the
driver should also indicate that it is switching to Shared Key mode by
setting exclude_unencrypted.
2) Initial authentication modes were apparently wrong in some cases,
causing the driver to attempt Shared Key authentication mode when in
fact the access point didn't support that mode or even had WEP disabled.
The driver should set the correct initial authentication mode based on
wep_is_on and exclude_unencrypted.
3) Authentication response packets from the access point in Open System
mode were getting ignored because the driver was expecting the sequence
number of a Shared Key mode response. The patch separates the OS and SK
mode handling to provide the correct behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch that added ENCODEEXT and AUTH support to the atmel
driver contained a slight error which would cause just setting the TX
key index to also set the encryption key again. This patch allows any
combination of setting the TX key index and setting an encryption key.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Below this point, the error path will proceed through
sis190_release_board(). It will happily oops if
pci_set_drvdata() has not been issued.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
drivers/net/appletalk/cops.c: In function `cops_load':
drivers/net/appletalk/cops.c:539: warning: assignment discards qualifiers from pointer target type
drivers/net/appletalk/cops.c:547: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orinoco wireless driver can support the SMC 2532W-B PC Card, so add the
id for it.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Firmware should go into /lib/firmware, not /etc/firmware.
Found by Alejandro Bonilla.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make the whole netdevices menu depend on NET, rather than having an empty
submenu when networking is disabled.
Indeed, almost the whole body of the menu was surrounded by if NETDEVICES,
and what was outside depended on NETCONSOLE which is inside the menu.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/tulip/uli526x.c: In function `__check_mode':
drivers/net/tulip/uli526x.c:1693: warning: return from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/s2io.c: In function `verify_l3_l4_lro_capable':
drivers/net/s2io.c:6638: warning: ISO C90 forbids mixed declarations and code
Cc: Ravinandan Arakali <Ravinandan.Arakali@neterion.com>
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix this:
drivers/built-in.o(.text+0x89469): In function `s2io_get_ethtool_stats':
drivers/net/s2io.c:5209: undefined reference to `__udivdi3'
Cc: Ravinandan Arakali <Ravinandan.Arakali@neterion.com>
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It returns a pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/bonding/bond_sysfs.c:263:27: warning: Using plain integer as NULL pointer
drivers/net/bonding/bond_sysfs.c:998:26: warning: Using plain integer as NULL pointer
drivers/net/bonding/bond_sysfs.c:1126:26: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add NETIF_F_TSO (NETIF_F_UFO) to BOND_INTERSECT_FEATURES so that it can
be used by a bonding device iff all its slave devices support TSO (UFO).
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Increase version, and get rid of out-dated comment.
Speed setting has worked for quite a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This hardware supports Message Signaled interrupts.
When setting up, use software interrupt to check for bad hardware.
Signed-off-by: Stephen Hemminger <shemminger @osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Move the interrupt clear to before processing, this avoids a
possible races with status delaying.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using the sky2 driver with bonding can result in oopses related to
reinitializing the PHY when the MAC address is changed (which bonding
is wont to do). This patch changes sky2_set_mac_address to take less
drastic measures.
This is analagous to the skge patch here:
http://lkml.org/lkml/2005/9/29/399
which fixed the issue here:
http://bugzilla.kernel.org/show_bug.cgi?id=5271
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This fixes setting rx_coalesce_usecs_irq via ethtool in sky2.
The write was directed to the wrong register.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There were bugs in mmconfig access to PCI space, up to and
include 2.6.16-rc1. These prevented the sky2 driver from being
able to clear PCI express errors.
This patch makes the driver check (during probe), for errors
in PCI config access and fail.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix suspend/resume for sky2. The status ring was getting reallocated
and a bunch of other mistakes. Also, check return from power_state
on resume.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sis900 defines 'cfgpmcsr' as an I/O space register, but CFGPMCSR is
in fact a config space register, and there is no register at offset
0x44 in I/O space, so delete the enum.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100 seems to have had a long standing bug where e100_init_hw was being
called when it should not have been. This caused a panic due to recent
changes that rely on correct set up in the driver, and more robust error
paths.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When we pull the PPP protocol off the skb, we forgot to update the
hardware RX checksum. This may lead to messages such as
dsl0: hw csum failure.
Similarly, we need to clear the hardware checksum flag when we use
the existing packet to store the decompressed result.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the total number of packets with collisions during transmission in
vp->stats.collisions.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure tg3_reset_task() is flushed in the close and suspend paths
as noted by Jeff Garzik.
In the close path, calling flush_scheduled_work() may cause deadlock
if linkwatch_event() is on the workqueue. linkwatch_event() will try
to get the rtnl_lock() which is already held by tg3_close(). So
instead, we set a flag in tg3_reset_task() and tg3_close() polls
the flag until it is cleared.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo's stealth lock validator detected that both thread acquire
dev->xmit_lock and tp->rx_lock in reverse order.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
priv->eeprom is a pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Yi Zhu <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's not used. Fix the following on alpha-eb66 as a side effect:
In file included from drivers/net/lp486e.c:75:
include/asm/io.h:20:1: warning: "SLOW_DOWN_IO" redefined
drivers/net/lp486e.c:59:1: warning: this is the location of the previous definition
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert: 40727198bf
These PHY changes hang the sungem driver on startup with Sun chips on
sparc64. Hopefully we can redo these changes in a way that doesn't
break non-Apple systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the r8169 driver to set devices to be full-duplex only when
auto-negotiate is disabled.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Some users have commented that it is unclear which driver they should be
using for their Marvell/SysKonnect network adapter, and which ones
are/aren't interchangable.
This patch attempts to reduce the confusion.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch allows ipw2100 driver to advertise the WPA-related encryption
options that it does really support. It's necessary to work correctly
with NetworkManager and other programs that actually check driver & card
capabilities.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds IWENCODEEXT and IWAUTH support to the airo driver for
WEP and unencrypted operation. No WPA though. It allows the driver to
operate more willingly with wpa_supplicant and NetworkManager.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After looking at the mailing list (and experiencing permanent driver lockups
while using hwcrypto=1) I think that disabling this option by default would
be better than otherwise.
Signed-off-by: Andreas Happe <andreashappe@snikt.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ronald Bultje <rbultje@ronald.bitfreak.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Yi Zhu <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a couple of errors regarding QoS, which results in
compile warnings and malfunction of the driver.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Checking the stack usage of my kernel, showed that ipw2200 had a few bad
offenders. This is on i386 32-bit:
0x00002876 ipw_send_associate: 544
0x000028ee ipw_send_associate: 544
0x000027dc ipw_send_scan_request_ext: 520
0x00002864 ipw_set_sensitivity: 520
0x00005eac ipw_set_rsn_capa: 520
The reason is the host_cmd structure is large (500 bytes). All other
functions currently using ipw_send_cmd() suffer from the same problem.
This patch introduces ipw_send_cmd_simple() for commands with no data
transfer, and ipw_send_cmd_pdu() for commands with a data payload and
makes the payload a pointer to the buffer passed in from the caller.
As an added bonus, the diffstat looks like this:
ipw2200.c | 260 +++++++++++++++++++++-----------------------------------------
ipw2200.h | 2
2 files changed, 92 insertions(+), 170 deletions(-)
and it shrinks the module a lot as well:
Before:
text data bss dec hex filename
75177 2472 44 77693 12f7d drivers/net/wireless/ipw2200.ko
After:
text data bss dec hex filename
61363 2488 44 63895 f997 drivers/net/wireless/ipw2200.ko
So about a ~18% reduction in module size.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't really help with why restarts happen, but the following patch
greatly increases the likelihood that a firmware reload will succeed
afterward on my thinkpad. It addresses two issues. First, sysfs module
loading and hotplug are asynchronous, and as such file operations on the
"loading" and "data" files are racy when you load 2 firmwares in quick
succession. Second, the timeout for DMAing the firmware needs to scale
with the size of the firmware being loaded. That is, the watchdog needs
to be on throughput, not on time alone.
I no longer get the firmware load errors, though this is at best a hacky
workaround for a racy interface. (Obviously, this does nothing to address
the fatal errors in firmware which cause reloads; it just causes the
initial loading and the reloads to work more often.)
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This substitutes Linux jiffies_to_msec() wherever there is a
computation for determining milliseconds from jiffies,
following lead from ieee80211 code. And it does a little cleanup.
"it's" == "it is" ... "its" == possessive "it". Indulge me. ;-)
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've added a new module param "bt_coexist" which defaults to OFF.
This does not seem to fix the firmware restarts, but it does do "the
right thing" and disables something that we were enabling by default:
signaling the Bluetooth h/w which channel we're on (whether or not the
BT h/w was out there).
Signed-off-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Nick Kralevich <nick.ipw2200@kralevich.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The indirect SRAM/register 8/16-bit write routines are broken for
non-dword-aligned destination addresses.
Fortunately, these routines are, so far, not used for non-dword-aligned
destinations, but here's a patch that fixes them, anyway.
The attached patch also adds comments for all direct/indirect I/O routine
variations.
Signed-off-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a BUG_ON for the latest ieee80211 change.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the following possible cleanups:
- make needlessly global functions static
- "extern inline" -> "static inline"
- #if 0 the unused global function ipw_led_activity_on()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global ipw2100_wpa_assoc_frame() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CRYPTO is a helper variable, and to make it easier for users, it should
therefore select'ed and not be listed in the dependencies.
drivers/net/wireless/airo.c requires CONFIG_CRYPTO for compilations.
Therefore, AIRO_CS also has to CRYPTO.
Additionally, this patch removes the #ifdef's for the non-compiling
CRYPTO=n case from drivers/net/wireless/airo.c.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the following changes:
- add a CONFIG_WIRELESS_EXT select'ed by NET_RADIO for conditional
code
- remove the now no longer required #ifdef CONFIG_NET_RADIO from some
#include's
Based on a patch by Jean Tourrilhes <jt@hpl.hp.com>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_PCMCIA=m, CONFIG_HOSTAP_CS=y doesn't compile.
Reported by "Gabriel C." <crazy@pimpmylinux.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ipw2100 driver misunderstood the parameter of txpower.
Tx Power off means turn off the radio, but the driver interpret it as
"can't set txpower". So when getting the txpower, it sets disabled=1 to
the iwconifg tool in managed mode. And the tool will display "Tx Power off"
when disabled=1.
Now, in managed mode, iwconfig will not show "TX Power" if the radio is not
switched off. It will only display "Tx Power off" only if the radio is killed.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ipw2100.c:2236: warning: `ipw2100_match_buf' defined
but not used
Cc: Yi Zhu <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MII registers read/write function blindly busy waits for an
amount of 1000 us (1 ms), then up to 200 ms. These functions are
called from irq disabled context. Depending on the clock management,
it triggers lost ticks events. Since the value is way above the
standard delay required for mii register access, it strangely looks
like a bandaid against posted writes.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5947
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The current orinoco_cs.c can issue the exact same error message for
2 different tests that can fail. Alter them so we can tell which
one of the two failed.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't expose the hardware register contents in platform_data.
The only things we allow the user to configure are autoneg, speed, and
duplex. Add specific platform_data fields for these values and remove
the registers configs.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use the common ethtool support functions of the MII library.
Add generic MII ioctl handler.
Add PHY parameter speed/duplex/negotiation initialization and modification.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Modify link up/down handling to use the functions from the MII
library. Note that I track link state using the MII PHY registers
rather than the mv643xx chip's link state registers because I think
it's cleaner to use the MII library code rather than writing local
driver support code. It is also useful to make the actual MII
registers available to the user with maskable kernel printk messages
so the MII registers are being read anyway
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add and use the following functions:
mv643xx_eth_port_enable_tx()
mv643xx_eth_port_enable_rx()
mv643xx_eth_port_disable_tx()
mv643xx_eth_port_disable_rx()
so that ports are enabled/disabled consistently.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tx_ring_skbs is actually a count of tx descriptors currently in use.
Since there may be multiple descriptors per skb, it is not the
same as the number of skbs in the ring.
Also change rx_ring_skbs to rx_desc_count to be consistent.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove duplicated code by having unicast and multicast code use
a common filter table function: eth_port_set_filter_table_entry().
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
mp->port_mac_addr is just a redundant copy of dev->dev_addr, so remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update dev->last_rx on packet receive
This fix corrects errors seen during configuration of the bonding driver.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch eliminates a spinlock recursion bug introduced recently.
Since eth_port_send() is always called with the lock held, we simply
remove the locking inside the function itself.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below is a patch for the Large Receive Offload feature.
Please review and let us know your comments.
LRO algorithm was described in an OLS 2005 presentation, located at
ftp.s2io.com
user: linuxdocs
password: HALdocs
The same ftp site has Programming Manual for Xframe-I ASIC.
LRO feature is supported on Neterion Xframe-I, Xframe-II and
Xframe-Express 10GbE NICs.
Brief description:
The Large Receive Offload(LRO) feature is a stateless offload
that is complementary to TSO feature but on the receive path.
The idea is to combine and collapse(upto 64K maximum) in the
driver, in-sequence TCP packets belonging to the same session.
It is mainly designed to improve 1500 mtu receive performance,
since Jumbo frame performance is already close to 10GbE line
rate. Some performance numbers are attached below.
Implementation details:
1. Handle packet chains from multiple sessions(current default
MAX_LRO_SESSSIONS=32).
2. Examine each packet for eligiblity to aggregate. A packet is
considered eligible if it meets all the below criteria.
a. It is a TCP/IP packet and L2 type is not LLC or SNAP.
b. The packet has no checksum errors(L3 and L4).
c. There are no IP options. The only TCP option supported is timestamps.
d. Search and locate the LRO object corresponding to this
socket and ensure packet is in TCP sequence.
e. It's not a special packet(SYN, FIN, RST, URG, PSH etc. flags are not set).
f. TCP payload is non-zero(It's not a pure ACK).
g. It's not an IP-fragmented packet.
3. If a packet is found eligible, the LRO object is updated with
information such as next sequence number expected, current length
of aggregated packet and so on. If not eligible or max packets
reached, update IP and TCP headers of first packet in the chain
and pass it up to stack.
4. The frag_list in skb structure is used to chain packets into one
large packet.
Kernel changes required: None
Performance results:
Main focus of the initial testing was on 1500 mtu receiver, since this
is a bottleneck not covered by the existing stateless offloads.
There are couple disclaimers about the performance results below:
1. Your mileage will vary!!!! We initially concentrated on couple pci-x
2.0 platforms that are powerful enough to push 10 GbE NIC and do not
have bottlenecks other than cpu%; testing on other platforms is still
in progress. On some lower end systems we are seeing lower gains.
2. Current LRO implementation is still (for the most part) software based,
and therefore performance potential of the feature is far from being realized.
Full hw implementation of LRO is expected in the next version of Xframe ASIC.
Performance delta(with MTU=1500) going from LRO disabled to enabled:
IBM 2-way Xeon (x366) : 3.5 to 7.1 Gbps
2-way Opteron : 4.5 to 6.1 Gbps
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hi,
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hi,
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
One of the if()s contains a call to de_is_running(),
which seems to be safe to replace, but someone with more
knownledge of the code might want to verify this...
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hi,
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is a problem with fragmented skb in s2io driver version 2.0.9.4
available in 2.6.16-rc1 kernel. The adapter will fail to transmit if
any scatter-gather skb arrives. This patch provides fix for the above
described problem.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On my laptop, the b44 device is created and the carrier state defaults
to ON when created by alloc_etherdev. This means tools like NetworkManager
see the carrier as On and try and bring the device up. The correct thing
to do is mark the carrier as Off when device is created.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since get_settings() returns a signed int and it gets checked
for < 0 to catch an error, res should be a signed int too.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make phy 0 actually be read, as it is not being right now as we have:
int mii_status = mdio_read(dev, phy, MII_BMSR);
int phyx = phy & 0x1f;
When we should have instead:
int phyx = phy & 0x1f;
int mii_status = mdio_read(dev, phyx, MII_BMSR);
so that when phy, in the end of the (phy = 1; phy <= 32...) loop gets
to 32 phyx gets to 0, i.e. we were reading at 32, when the intended
read was for 0.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On my latest laptop, I've had occasional PHY dead on wakeup from
sleep... the PHY would be totally unresponsive even to toggling the hard
reset line until the machine is powered down... Looking closely at the
code, I found some possible issues in the way we setup the MDIO lines
during suspend along with slight divergences from what Darwin does when
resetting it that may explain the problem. That patch change these and
the problem appear to be gone for me at least... I also fixed an mdelay
-> msleep while I was at it to the pmac feature code that is called
when toggling the PHY reset line since sungem doesn't call it in an
atomic context anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>b
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.4.31 and add 2006 copyright.
Skip the last digit when reporting the firmware version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance the ethtool loopback test with PHY loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for a hardware interrupt issue. When using INTA,
unmasking of the interrupt and the tag update should be done
separately to avoid some spurious interrupts,
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TCP/UDP checksum verification. Use status bits in the buffer
descriptor instead of the checksum value to verify rx checksum.
Using the checksum value will be incorrect if the UDP packet has
zero in the UDP checksum field.
Firmware update required for this fix.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc. fixes for WoL, 5708 B1, and a typo '=' instead of '=='.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve handshake with bootcode with the following changes:
1. Increase timeout to 100msec and use msleep instead of udelay.
2. Add more error checking for timeouts and errors.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always set up the device to strip incoming VLAN tags when ASF is
enabled. ASF firmware will not parse packets correctly if VLAN tags
are not stripped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove page refcount manipulations from cassini driver by using
another field in struct page. Needed for lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
in attempting to not send the "prefetch" patch, we broke the receive code,
this patch fixes that issue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added e1000_mc_addr_list_update
Added e1000_read_reg_io
Added e1000_enable_pciex_master
These are not static functions, that is why we have them declared in the header.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These functions help restore the driver to active configuration when coming out of resume for power management.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Align the prefetches to a dword to help speed them up.
Recycle skb's and early replenish.
Force memory writes to complete before fetching more descriptors.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sizeof() return is not an int, so use max_t to get the types right.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about transmit locking, this solves a possible race
between tx_complete and transmit, that would cause a tx timeout.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to inline quite so many routines, let the compiler
decide
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make sure and rate limit all the error messages that might occur. If a problem
occurs then a few messages are enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Small optimization, if dma addresses are 32 bits, then high
bits are always zero.
Signed-off-by: Stephen Hemminger <shemminger@osdl.or>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to zero out the status ring entries after processing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about memory barriers. The only place we really
need them is before and after updating the chip's ring interface.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from
sk98lin driver. Change how the ram buffer is divided up, and make the math
clearer. Also, set the thresholds where rx takes precedence. The threshold
values are just guesses at this point, it might be worth tuning them later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to call pci_set_consistent_dma_mask in the case of 64 bit
DMA.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to make sure that sky2 receive buffers are 64 bit
aligned. Also, don't need to start off with GFP_ATOMIC
on initial setup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements suspend and resume methods for the starfire driver. It
allows me to put my desktop PC with a starfire dual board into S4.
Signed-Off-By: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: e100 whitespace fixes
These are whitespace only fixes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Handle the return values from pci_* functions
This is to resolve warnings during compile time.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue)
Set the end of list bit to cause the hardware's transmit state machine to
work correctly and not prevent management (BMC) traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/cassini.c:1930: warning: long unsigned int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups:
- make needlessly global code static
- arcnet.c: remove the unneeded EXPORT_SYMBOL(arc_proto_null)
- arcnet.c: remove the unneeded EXPORT_SYMBOL(arcnet_dump_packet)
To make Jeff happy, arcnet.c still prints
arcnet: v3.93 BETA 2000/04/29 - by Avery Pennarun et al.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
