When capturing a 60 Hz input the internal field ID is inverted. The
VIDIOC_INT_G_VBI_DATA didn't take that into account and so returned
XDS instead of CC and vice versa.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before, root privileges were only needed to set hardware registers, not
to read them. On some hardware, reading from the wrong place at the
wrong time can hang the machine. So, to be consistent, root privileges
are required to read registers on all hardware.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The direct register access ioctls were defined as kernel internal only,
but they are very useful for debugging hardware from userspace and are
used as such. Officially export them.
VIDIOC_INT_[SG]_REGISTER is renamed to VIDIOC_DBG_[SG]_REGISTER
Definition of ioctl and struct v4l2_register is moved from v4l2-common.h
to videodev2.h.
Types used in struct v4l2_register are changed to the userspace
exportable versions (u32 -> __u32, etc).
Use of VIDIOC_DBG_S_REGISTER requires CAP_SYS_ADMIN permission, so move
the check into the video_ioctl2() dispatcher so it doesn't need to be
duplicated in each driver's call-back function. CAP_SYS_ADMIN check is
added to pvrusb2 (which doesn't use video_ioctl2).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Nexus CA needs to use a different routing on saa7115 module.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old code would accept any device on the same i2c address as the
saa711x chips as an saa711x. However, this fails with saa717x chips,
which use that same address and so are misdetected as a saa7111. Now
check whether the chip is really a saa711x model.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without the attached trivial patch, the saa7113 is set up for PAL when SECAM
is selected and hence will see only show black and white for SECAM signals.
Tested the patch against the saa7115 module in linux-2.6.17 with a
Pinnacle 50e USB tuner (em28xx).
Signed-off-by: Pádraig Brady <P@draigBrady.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This repairs a problem introduced by a commit earlier applied.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Scaling were not working fine;
Some reserved registers were wrong;
On some situations, saa7115 were not properly being initializated.
Removed some duplicated code.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl> for co-working on this
patch.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7115 module is capable of calculating the proper FIR tables.
However, there were 4 hardcoded tables for the standard resolution.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Replace hardcoded control description by the standard ones supplied
by v4l2-common.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some saa7115-based cards use a different crystal frequency and a different
audio clock generation. Add a new VIDIOC_INT_S_CRYSTAL_FREQ command to be
able to set these values.
Also change the default APLL setting to 0. It makes no sense to have the
audio clock independent from the video clock, this can lead to audio/video
synchronization problems. Setting this to 0 is also consistent with the old
saa7114.c source and the way the Hauppauge Windows driver sets it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The sliced VBI defines added in videodev2.h are removed since requires
more discussion.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanup audio input handling in bttv and tvaudio:
- inputs were specified that were never used
- mute was handled as a special input which led to confusing code
- confusing naming made it difficult to see if the setting was for
i2c or gpio.
The old audiochip.h input names moved to tvaudio.h. Currently this
is used both by tvaudio and msp3400 until the msp3400 implements the
new msp3400-specific inputs.
Detect in bttv the tvaudio and msp3400 i2c clients and use these
client pointers to set the inputs directly instead of broadcasting the
command.
Removed AUDC_SET_INPUT. Now replaced by VIDIOC_S_AUDIO. This will be
replaced again later by the new ROUTING commands.
Removed VIDIOC_G_AUDIO implementations in i2c drivers: this command is
a user level command and not to be used internally. It wasn't called at
all anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_STD_PAL define is not correct. It specifies only 50Hz PAL standards.
This patch fixes saa7113 color config for other PAL video standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes chroma standard selection based at possible values,
according with datasheet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, em28xx uses saa7115 instead of saa711x.
saa7115 driver is capable of handling saa 7113, 7114 and 7115.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added other sliced VBI types to videodev2.h
- tvp5150 now uses standard V4L2 API codes from videodev2.h
- Implemented VIDIOC_G_SLICED_VBI_CAP for tvp5150. This is
dynamically filled based on defined VDP C-RAM values filled
by the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Debug global var is already used inside kernel.
- v4l_dbg now expects the debug var
- global vars inside msp34xx renamed to msp_*
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Convert diagnostics over to the new v4l2-common.h macros.
- deprecated tuner_debug option, the new option is debug.
- renamed cx25840_debug to debug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Detect when AUDC_SET_RADIO is called.
- When in radio mode ignore VIDIOC_G_TUNER.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Don't reprogram the video standard if the new standard
equals the old standard.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Calculate the audio master clock registers from the actual
frequencies. This simplifies the code and it also prepares
for adding CGC2 support.
- VIDIOC_INT_AUDIO_CLOCK_FREQ now receives an u32 instead of
an enum. It is more generic and actually easier to implement.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers/media/video and usb/media drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Adds support for saa7115 video decoder.
Driver Authors: Hans Verkuil, Chris Kennedy, Kevin Thayer
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
