[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 229d495d8189ae785dacee72e5633a58edc25ddf ]
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 148c847c9e5a54b99850617bf9c143af9a344f92 ]
pwmX_enable supports three possible values:
0: Fan control disabled. Duty cycle is fixed to 0%
1: Fan control enabled, pwm mode. Duty cycle is determined by
values written into Target Duty Cycle registers.
2: Fan control enabled, rpm mode
Duty cycle is adjusted such that fan speed matches
the values in Target Count registers
The current code does not do this; instead, it mixes pwm control
configuration with fan speed monitoring configuration. Worse, it
reports that pwm control would be disabled (pwmX_enable==0) when
it is in fact enabled in pwm mode. Part of the problem may be that
the chip sets the "TACH input enable" bit on its own whenever the
mode bit is set to RPM mode, but that doesn't mean that "TACH input
enable" accurately reflects the pwm mode.
Fix it up and only handle pwm control with the pwmX_enable attributes.
In the documentation, clarify that disabling pwm control (pwmX_enable=0)
sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN
is set together with RPM_MODE.
While at it, only update the configuration register if the configuration
has changed, and only update the cached configuration if updating the
chip configuration was successful.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@cesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 897f6339893b741a5d68ae8e2475df65946041c2 ]
The MAX31790 has two sets of registers for pwm duty cycles, one to request
a duty cycle and one to read the actual current duty cycle. Both do not
have to be the same.
When reporting the pwm duty cycle to the user, the actual pwm duty cycle
from pwm duty cycle registers needs to be reported. When setting it, the
pwm target duty cycle needs to be written. Since we don't know the actual
pwm duty cycle after a target pwm duty cycle has been written, set the
valid flag to false to indicate that actual pwm duty cycle should be read
from the chip instead of using cached values.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@ceesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-3-linux@roeck-us.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sphinx is generating a build warning as the title underline
of this file is too short.
Signed-off-by: Adam Zerella <adam.zerella@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When generating documentation output Sphinx
outputs a warning for not including
the page 'inspur-ipsps1.rst' in 'index.rst'.
Assuming this documentation is useful it
should be included in the index.
Signed-off-by: Adam Zerella <adam.zerella@gmail.com>
Link: https://lore.kernel.org/r/20190925131715.GB19073@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It's been a while since the k10temp documentation has been updated.
There are new CPU families supported as well as Tdie temp was added.
This patch adds all missing families which I was able to find from git
history and provides more info about Tctl vs Tdie exported temps.
Signed-off-by: Lukas Zapletal <lzap+git@redhat.com>
Link: https://lore.kernel.org/r/20190923105931.27881-1-lzap+git@redhat.com
[groeck: Formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
New driver should use devm_hwmon_device_register_with_info() or
hwmon_device_register_with_info() to register with the hwmon subsystem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.
This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190819091509.29276-1-wangzqbj@inspur.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This document was recently introduced. Convert it to ReST
just like the other hwmon documents, adding it to the hwmon index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert each file at I2C subsystem, renaming them to .rst and
adding to the driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The audience for the Kernel driver-model is clearly Kernel hackers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice driver changes
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Convert the various documents at the driver-model, preparing
them to be part of the driver-api book.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMP75B has a different control register, supports 12-bit
resolution and the default conversion rate is 37 Hz.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On almost all places, we're including ReST files without the
extension.
Let's remove the extension here as well, in order to use just
one standard.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Those three new drivers were missed on the initial conversion
to ReST format. So:
- Rename them to .rst;
- Add them to the hwmon index.rst index;
- add some blank lines at the "Supported systems:" part, in
order to allow Sphinx to properly identify new lines,
suppressing warnings and avoid it to output some random
lines in bold;
- When multiple authors are involved, change the authors
part to a list, in order to avoid adding blank lines.
- adjust the table cells (one of the tables seemed to be
assuming that tab is 4 positions instead of 8) and add
the table markup.
- be sure that the section markups have the same number of
characters as the section title.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The CONFIG register has two 3-bit fields for conversion time
settings of Bus-voltage and Shunt-voltage, respectively. The
conversion settings, along with averaging mode, allow users
to optimize available timing requirement.
This patch adds an 'update_interval' sysfs node through the
hwmon_chip_info of hwmon core. It reflects a total hardware
conversion time:
samples * channels * (Bus + Shunt conversion times)
Though INA3221 supports different conversion time setups for
Bus and Shunt voltages, this patch only adds the support of
a unified setting for both conversion times, by dividing the
conversion time into two equal values.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[groeck: .rst related formatting changes in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert all other hwmon files to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert other files maintained by Guenter to ReST format, in order
to allow them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert pmbus files to ReST format, in order to allow them to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert k8temp and w83793 to ReST format, in order to allow them
to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert da9052 and da9055 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert wm831x and wm8350 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert dme1737 and vt1211 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert ads1015 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert asc7621 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert ibmpowernv to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert aspeed-pwm-tacho to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert coretemp to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert w83791d to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert fam15h_power to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert pc87360 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert emc2103 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert sch5627 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert menf21bmc to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert vexpress to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert k10temp to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The CONFIG register has a 3-bit averaging mode field for users
to setup the number of samples that are collected and averaged
together. This is very useful to filter noise from sensor data.
This patch adds a 'samples' sysfs node using hwmon_chip_samples
of hwmon core, and updates wait time calculation by taking this
samples value into account.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intersil ISL68137 is a digital output 7-phase configurable PWM
controller with an AVSBus interface.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document new ABI attributes: {in,power,curr,temp}_samples and samples.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
