The original implementation of the constraints were good against sane
applications.
If the opening sequence is:
stream1_open, stream1_hw_params, stream2_open, stream2_hw_params -> the
constraints are set correctly for stream2.
But if the sequence is:
stream1_open, stream2_open, stream2_hw_params, stream1_hw_params -> than stream2
would receive constraint rate = 0, sample_bits = 0, since the stream1 has not
yet called hw_params...
The command to trigger this event:
gst-launch-0.10 alsasrc device=hw:0 ! alsasink device=hw:0 sync=false
This patch does some 'black magic' in order to always set the correct
constraints and sets it only when it is needed for the other stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DSP_A mode is similar to the DSP_B, but the MSB is delayed with
one bclk (appears after the FS pulse and not under it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use single-phase mode for the DSP mode and keep the dual phase
mode for the I2S mode.
The mono (1 channel) mode already used single phase mode,
now it is more cleaner. There is no need to configure the
second phase, when the single phase is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using inverted FS polarity in OSK5912 must be an error since TLV320AIC23
do not have support for inverted polarities. This is mostly due the hassle
with the DSP formats in OMAP McBSP DAI and inversion on OMAP side probably
just made this configuration working at some point.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a6c.
Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with FWID(0).
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix accidental change of <mach/regs-gpio.h> to
<plat/regs-gpio.h> in s3c2412-i2s.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the build error in s3c-i2s-v2.c caused by
a change to the snd_soc_dai ops field.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The definition of s3c_i2sv2_iis_calc_rate was never
renamed from s3c2412_iis_calc_rate, so rename this
to allow the build to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build errors in sound/soc/s3c24xx/jive_wm8750.c
from changes to ASoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa_ssp_set_dai_fmt() currently has an early exit if the desired format
equals the current configuration. This is correct behaviour unless this
function is called with a zero value parameter for the first time.
Zero is a valid value for this function, but the early exit is bogus in
this case.
Hence, set priv->dai_fmt to -1 in the beginning so we can configure the
port.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some limited volume controls (mostly simple attenuations) have only two
settings so the ASoC info functions misreport them as booleans. Since
we currently have no better information check for " Volume" in the
control name and always report any controls matching as being integer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8960 is a low power, high quality stereo codec designed for
portable digital audio applications.
Stereo class D speaker drivers provide 1W per channel into 8W loads.
Guaranteed low leakage, excellent PSRR and pop/click suppression
mechanisms enable direct battery connection for the speaker supply.
The device also integrates a complete microphone interface and a stereo
headphone driver. External component requirements are drastically
reduced as no separate microphone, speaker or headphone amplifiers are
required. Advanced on-chip digital signal processing performs automatic
level control for the microphone or line input.
Stereo 24-bit sigma-delta ADCs and DACs are used with low power
over-sampling digital interpolation and decimation filters and a
flexible digital audio interface.
The master clock can be input directly or generated internally by an
onboard PLL, supporting most commonly-used clocking schemes.
This driver was originally written by Liam Girdwood, with substantial
subsequent additions and updates for feature completeness and changes in
the ASoC framework from me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SCMODE(0): Data Driven (Falling), Data Sampled (Rising), Idle State (Low)
SCMODE(1): Data Driven (Rising), Data Sampled (Falling), Idle State (Low)
SCMODE(2): Data Driven (Rising), Data Sampled (Falling), Idle State (High)
SCMODE(3): Data Driven (Falling), Data Sampled (Rising), Idle State (High)
SCMODE(3) does not invert the clock polarity compared to the default SCMODE(0).
This patch also adds all possible NF/IF, NB/IB combinations to the DSP_A and
DSP_B modes.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures that we sync with the DAPM powerdown sequencing properly
and don't need to bounce the power on the voice DAC so often.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is simple code motion, intended to support future refactoring of
the DAPM algorithms and (more immediately) the additon of events for
DACs and ADCs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to the process and communications issues with the 2.6.30 S3C
platform merges none of the underlying arch/arm code for S3C64xx audio
support made it into mainline, rendering the drivers useless. Disable
them in Kconfig to avoid user confusion - users patching in the required
support can always reenable this too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DSP_A interface format support by setting the LRP bit in
DSP mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8988 is a low power, high quality stereo CODEC designed for
portable digital audio applications.
The device integrates complete interfaces to 2 stereo headphone or line
out ports. External component requirements are drastically reduced as no
separate headphone amplifiers are required. Advanced on-chip digital
signal processing performs graphic equaliser, 3-D sound enhancement and
automatic level control for the microphone or line input.
The WM8988 can operate as a master or a slave, with various master clock
frequencies including 12 or 24MHz for USB devices, or standard 256fs
rates like 12.288MHz and 24.576MHz. Different audio sample rates such as
96kHz, 48kHz, 44.1kHz are generated directly from the master clock
without the need for an external PLL.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many devices require symmetric configurations of capture and playback
data formats, often due to shared clocking but sometimes also due to
other shared playback and record configuration in the device. Start
providing core support for this by allowing the DAIs or the machine
to specify that the sample rates used should be kept symmetric.
A flag symmetric_rates is provided in the snd_soc_dai and
snd_soc_dai_link structures. If this is set in either of the DAIs or in
the machine then a constraint will be applied when a stream is already
open preventing any changes in sample rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (36 commits)
ALSA: hda - Add VREF powerdown sequence for another board
ALSA: oss - volume control for CSWITCH and CROUTE
ALSA: hda - add missing comma in ad1884_slave_vols
sound: usb-audio: allow period sizes less than 1 ms
sound: usb-audio: save data packet interval in audioformat structure
sound: usb-audio: remove check_hw_params_convention()
sound: usb-audio: show sample format width in proc file
ASoC: fsl_dma: Pass the proper device for dma mapping routines
ASoC: Fix null dereference in ak4535_remove()
ALSA: hda - enable SPDIF output for Intel DX58SO board
ALSA: snd-atmel-abdac: increase periods_min to 6 instead of 4
ALSA: snd-atmel-abdac: replace bus_id with dev_name()
ALSA: snd-atmel-ac97c: replace bus_id with dev_name()
ALSA: snd-atmel-ac97c: cleanup registers when removing driver
ALSA: snd-atmel-ac97c: do a proper reset of the external codec
ALSA: snd-atmel-ac97c: enable interrupts to catch events for error reporting
ALSA: snd-atmel-ac97c: set correct size for buffer hardware parameter
ALSA: snd-atmel-ac97c: do not overwrite OCA and ICA when assigning channels
ALSA: snd-atmel-ac97c: remove dead break statements after return in switch case
ALSA: snd-atmel-ac97c: cleanup register definitions
...
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_28BIT_MASK macro with DMA_BIT_MASK(28)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix for compillation error introduced by the constrain patch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add powerdown sequence for VREF using a shared jack when the headphone
is present and the microphone isn't on.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added an else part to check
SNDRV_MIXER_OSS_PRESENT_CVOLUME for MIC (slot 7)
in commit 36c7b833e5
Similarly, checks and volume control is required for
SNDRV_MIXER_OSS_PRESENT_CSWITCH and SNDRV_MIXER_OSS_PRESENT_CROUTE
as well.
Signed-off-by: Deepika Makhija <deepika.makhija@einfochips.com>
Signed-off-by: Viral Mehta <viral.mehta@einfochips.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable periods shorter than 1 ms, we have to make sure that short
periods are only available for alternate settings that have a small
enough data packet interval. Furthermore, the code that aligns URBs to
USB frames is now superfluous.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The data packet interval needs to be available in the audioformat
structure, together with the other audio format parameters, so that it
can be used to influence ALSA hardware parameters.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes the check_hw_params_convention() function because
1) it is not necessary, as the hw_rule_* functions also work correctly
(i.e., as no-ops) when the device supports all combinations of the
audio format parameters; and
2) it would become too complex when adding a fourth altsetting-dependent
hardware parameter, as this would require another three loops to
check dependecies with rate/channels/format.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When listing the device's sample formats in the stream? proc file, the
sample format number itself is rather obscure, so we better show the
format width, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
