This patch adds support for the LAN9118 ethernet on rsk7203.
The LAN9118 controller is hooked up using a 16-bit data bus,
but the rsk7203 board does not swap the byte lanes as needed
between the sh7203 processor and the the ethernet controller.
In the processor the CS memory window is configured in 16-bit
mode but the smsc911x driver is told to do 32-bit accesses to
improve performance. The SMSC911X_SWAP_FIFO flag is used
to tell the driver to do software byte swapping of fifo data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Urquell has a system FPGA capable of reading the mode pin states from
software, wire this up in the machvec.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The irqsoff tracer uses the atomic_* functions internally, but the
implementations of those functions in arch/sh/include/asm/atomic-irq.h
disable irqs to achieve atomicity. A continuous loop ensues where we
disable interrupts, trace the interrupt disabling, call atomic_*
functions, disable interrupts, trace the interrupt disabling, etc..
The simplest solution to all this is to just convert uses of
local_irq_save()/local_irq_restore() the raw_* equivalents because the
raw_* equivalents don't call trace_hardirqs_on()/trace_hardirqs_off().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The asm-generic versions have some helper definitions that we can use
instead, drop our definitions and use those instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the earlytimer probe handles the clockevents driver, which
requires that the clockevents driver be registered first. This bumps it
up by 1 to include the clocksource device, which can be safely ignored
if it doesn't exist, as we will simply error out on that path and defer
to the jiffies clocksource.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were handled through late_time_init due to kmalloc() and friends
not being available earlier on previously. Now with slab caches being
available much earlier, this is no longer necessary, and we can move the
initialization up to an earlier point. One of the benefits with this is
that printk times are available a bit earlier!
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the accessors rather than frobbing bits directly (the new versions
are const).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Makes code futureproof against the impending change to mm->cpu_vm_mask.
It's also a chance to use the new cpumask_ ops which take a pointer
(the older ones are deprecated, but there's no hurry for arch code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We're weaning the core code off handing cpumask's around on-stack.
This introduces arch_send_call_function_ipi_mask(), and by defining
it, the old arch_send_call_function_ipi is defined by the core code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Everyone cut and paste this comment from my original one. We now do
it generically, so cut the comments.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Amerigo Wang <amwang@redhat.com>
The current asm-generic/page.h only contains the get_order
function, and asm-generic/uaccess.h only implements
unaligned accesses. This renames the file to getorder.h
and uaccess-unaligned.h to make room for new page.h
and uaccess.h file that will be usable by all simple
(e.g. nommu) architectures.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic/atomic.h only defines the
atomic_long type. This renames it to atomic-long.h
so we have a place to add a truly generic atomic.h
that can be used on all non-SMP systems.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
This provides a reliable way for asm-generic/types.h and other
files to find out if it is running on a 32 or 64 bit platform.
We cannot use CONFIG_64BIT for this in headers that are included
from user space because CONFIG symbols are not available there.
We also cannot do it inside of asm/types.h because some headers
need the word size but cannot include types.h.
The solution is to introduce a new header <asm/bitsperlong.h>
that defines both __BITS_PER_LONG for user space and
BITS_PER_LONG for usage in the kernel. The asm-generic
version falls back to 32 bit unless the architecture overrides
it, which I did for all 64 bit platforms.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic versions are incomplete and included
by some architectures. New architectures should be able
to use a generic version, so rename the existing files and
change all users, which lets us add the new files.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ftrace on sh handles nop'ing out trace function calls differently than
other architectures. Instead of inserting NOP instructions in place of
the call to the function tracer we branch over the call instructions
and continue executing the main body of the function.
This patch fixes a bug in the implementation of ftrace_modify_code()
where we check that the old value of the code we're about to replace
is an expected one. In the ftrace_make_call() code path
ftrace_modify_code() was comparing the old instruction value with NOP
instructions. The compare was failing because we never actually insert
NOP instructions. It makes sense to just get rid of the NOP
instructions in ftrace_nop and compare the old code with the address
of the function body if we're expecting ftrace to have nop'd out the
function trace call.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a typo here that had this as sys_writev() instead of
sys_pwritev(), fix this up. sh64 got this right, as did the preadv()
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up a typo in the ll/sc based cmpxchg code which apparently
wasn't getting a lot of testing due to the swapped old/new pair. With
that fixed up, the ll/sc code also starts using it and provides its own
atomic_add_unless().
Signed-off-by: Aoi Shinkai <shinkoi2005@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7722 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
While at it, now when all SuperH Mobile processors
are converted, fix CONFIG_SH_CLK_CPG_LEGACY to depend
on CONFIG_ARCH_SHMOBILE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7366 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7343 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V3 of the sh7724 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and fll are
supported as input clocks to the pll. The div6 clocks are
fed through a divide-by-3 block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V2 of the sh7723 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and dll
are supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the div6 clock helper code to add support
for enable(), disable() and set_rate() callbacks.
Needed by the camera clock enabling board code on Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin configuration and
a machvec structure to Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7722 mode pin and pin function
controller comments.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds comments for the sh7724 mode pins
and pin function controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is sh7723 mode pin V2. Mode pins and
pin function controller comments are added.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the mode pin code to keep the pin
definitions in one place. The mode pins values are now
the value of the bit instead of bit number.
With this patch in place the sh7785 header file contains
mode pin comments. The sh7785 clock code and the sh7785lcr
board code are updated to reflect the new shared mode pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds div6 clock helper code. The div6 clocks
are simply 6-bit divide-by-n modules where n is 1 to 64.
Needed for vclk on sh7722, sh7723, sh7343 and sh7366.
sh7724 needs this even more for vclk, fclka, fclkb,
irdaclk and spuclk.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the per clock offset calculation in
sh_clk_div4_register(). Without this patch the offset
to the frequency table for each clock is incorrect.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The vsyscall targets are presently not cleaned up, so just handle it in
the archclean rule.
Reported-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the 16-bit case of the sh4a specific
unaligned access implementation. Without this patch
the 16-bit version of sh4a get_unaligned() results in
a 32-bit read which may read more data than intended
and/or cross page boundaries.
Unbreaks mtd NOR write handling on Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CONFIG_SH_PCLK_FREQ=33333333 is correct for sh7724.
sh7724 master clock is 33333333, but peripheral is 41666666.
This bug came to light because sh-sci driver had changed clk
from "module_clk" to "peripheral_clk"
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up the boot_cpu_data.flags probing on SH-4A. All of them have
a few things in common, which we can blindly set, rather than having each
subtype have to set the same flags. We can also make assumptions about
cache ways and the validity of PTEA, so this also kills off CPU_HAS_PTEA
as a config option. There was also a bug in the FPU probing, which is now
tidied up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up the L2 probing, as it may or may not be implemented on a
CPU, regardless of whether it is supported. This converts the cvr
validity checks from BUG_ON()'s to simply clearing the CPU_HAS_L2_CACHE
flag and moving on with life.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add shared code for 4-bit divisor clocks.
Processor specific code can use SH_CLK_DIV4()
to initialize div4 clocks, and then use
sh_clk_div4_register() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add shared 32-bit module stop bit clock support.
Processor specific code can use SH_CLK_MSTP32()
to initialize module stop bit clocks, and then
use sh_clk_mstp32() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the CPU_HAS_L2_CACHE flag to SH7724.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modifies the sh7785 clock code to use the MODE4
value to switch between 72x and 36x PLL multiplication.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin support to the sh7785lcr board.
The harware allows the user to control the mode pins using
dip switches S1 and S2, but from the software the pins are
fixed to the factory default since we have no way to reading
out this configuration from software.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7785 mode pin definitions. Mode pins and
pin function controller comments are added as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add mode pin support for the SuperH architecture V2.
With this patch applied the board code can add their
own function to export the cpu mode pin configuration.
In most cases this will be a constant bitmap, but
boards that allow reading this from a register can
instead read out the pin state from hardware.
The code warns if a pin is tested but no board specific
mode pin function has been provided.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The flat loader uses an architecture's flat_stack_align() to align the
stack but assumes word-alignment is enough for the data sections.
However, on the Xtensa S6000 we have registers up to 128bit width
which can be used from userspace and therefor need userspace stack and
data-section alignment of at least this size.
This patch drops flat_stack_align() and uses the same alignment that
is required for slab caches, ARCH_SLAB_MINALIGN, or wordsize if it's
not defined by the architecture.
It also fixes m32r which was obviously kaput, aligning an
uninitialized stack entry instead of the stack pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build error where references to pci_cache_line_size are
undefined, as this ceases to be exported when PCI_DISABLE_MWI is enabled,
as is now the default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
None of the SH PCI controllers support MWI, it is always treated as a
direct memory write, so simply disable it outright. In the case of the
PCI cache line size, consult that for the pci_dma_burst_advice()
strategy, and switch over to PCI_DMA_BURST_MULTIPLE, as PPC64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As there is only a single controller and remapping has no impact for the
address range in question, just initialize it directly in the controller
definition. This fixes up boot time warnings about not having the field
initialized.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the ->build_rate_table() callback,
->recalc() may instead be used for this purpose.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the sh7785 clock code to make use
of clk_rate_table_build() and clk_rate_table_round().
The ->build_rate_table() callback is removed, the
table building is instead handled in ->recalc().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the sh7785 pll implementation from the
all-in-one code in frqmr_recalc() and frqmr_build_rate_table()
to a separate struct clk. This allows us to remove the processor
specific multiplier and use generic rate table functions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the ms7724se solution engine board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off after_bootmem and switches to using slab_is_available()
instead. Presently the only place this is used is by the sh64 ioremap,
and there's not much point in keeping the reference around otherwise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new SH_CLK_CPG for parts that have CPG support.
SH_CLK_CPG_LEGACY is made to depend on this, and still needs to be set
for platforms that want clock-cpg to register the legacy clocks. With
this new config item in place, it is now possible to start layering more
generic CPG code in place while other platforms transition off of the
legacy clocks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
irq_to_desc_alloc_cpu() has been renamed to irq_to_desc_alloc_node() in
-next, but as we can not presently enable SPARSE_IRQ without the early
irq_desc alloc patch, protect it with an ifdef until the interface has
settled and we are ready to enable it system-wide.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the ap325rxa ncm03j camera code to handle
the case where no i2c driver is present. Without this fix
i2c_transfer() may be passed NULL as adapter which results
in a crash.
Triggered when i2c-sh_mobile.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is just a simple arch_probe_nr_irqs() stub that wraps to the
platform defined number of IRQs. This can be made gradually more
intelligent based on what we can infer from the INTC tables and so on.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
