Some BIOSes do not indicate error when trying to read from non-
existing device. Zero buffer before reading and check that we
possibly have valid MBR by looking for MBR magic.
This was fixed in different way for edd.S in
http://marc.info/?l=linux-kernel&m=114087765422490&w=2, but lost
again when edd.S was rewritten in C.
Signed-off-by: Andrey Borzenkov < arvidjaar@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
> This is regression but old enough. Apparently I had for whatever reasons
> EDD turned off till recently. This is 2.6.27-rc5 just in case.
>
> In 2006 I fixed ghost devices due to buggy BIOS:
>
> http://marc.info/?l=linux-kernel&m=114087765422490&w=2
>
> Later edd.S has been rewritten in C, and apparently this patch has been
> lost:
>
> {pts/1}% ls /sys/firmware/edd
> int13_dev80/ int13_dev84/ int13_dev88/ int13_dev8c/
> int13_dev81/ int13_dev85/ int13_dev89/ int13_dev8d/
> int13_dev82/ int13_dev86/ int13_dev8a/ int13_dev8e/
> int13_dev83/ int13_dev87/ int13_dev8b/ int13_dev8f/
>
> But I have just a single disk. This is the same system BTW.
Some BIOSes do not always set CF on error before return from int13.
The patch adds additional check for status being zero (AH == 0).
This was fixed for edd.S in
http://marc.info/?l=linux-kernel&m=114087765422490&w=2, but lost
again when edd.S was rewritten in C.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When building image.iso (make isoimage), use the isohybrid tool if it
exists. isohybrid is a script included with Syslinux 3.72 and higher,
which creates an image that can be booted either as a hard disk
(including removable, e.g. USB disk) or as a CD-ROM.
If isohybrid doesn't exist, then this has no effect.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Kbuild variable "targets" is supposed to be
configuration-independent and reflect "all possible targets". This is
required to make "make clean" work properly.
Therefore, move all manipulation of "targets" as well as custom rules
out of the x86-32 ifdef statement. Only leave inside the ifdefs the
things that are genuinely configuration-dependent.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
Video mode selection became always possible in 2.6.23-rc1 after i386 setup
code rewrite in C.
Regardless, VIDEO_SELECT is stupid config option because it affects only
kernel setup code, not code which always stays in memory.
vga= always possible now which is good.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Without checking the return value of get_edd_info() and adding the
entry only in the success case, 6 devices show up under
/sys/firmware/edd/, no matter how many devices are actually present.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix asm/e820.h for userspace inclusion
x86: fix numaq_tsc_disable
x86: fix kernel_physical_mapping_init() for large x86 systems
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: do not trace library functions
ftrace: do not trace scheduler functions
ftrace: fix lockup with MAXSMP
ftrace: fix merge buglet
fix:
arch/x86/kernel/numaq_32.c: In function ‘numaq_tsc_disable’:
arch/x86/kernel/numaq_32.c:99: warning: ‘return’ with a value, in function returning void
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
-tip testing found a bootup hang here:
initcall anon_inode_init+0x0/0x130 returned 0 after 0 msecs
calling acpi_event_init+0x0/0x57
the bootup should have continued with:
initcall acpi_event_init+0x0/0x57 returned 0 after 45 msecs
but it hung hard there instead.
bisection led to this commit:
| commit 5806b81ac1
| Merge: d14c8a6... 6712e29...
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Mon Jul 14 16:11:52 2008 +0200
| Merge branch 'auto-ftrace-next' into tracing/for-linus
turns out that i made this mistake in the merge:
ifdef CONFIG_FTRACE
# Do not profile debug utilities
CFLAGS_REMOVE_tsc_64.o = -pg
CFLAGS_REMOVE_tsc_32.o = -pg
those two files got unified meanwhile - so the dont-profile annotation
got lost. The proper rule is:
CFLAGS_REMOVE_tsc.o = -pg
i guess this could have been caught sooner if the CFLAGS_REMOVE* kbuild
rule aborted the build if it met a target that does not exist anymore?
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.
When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.
This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.
http://bugzilla.kernel.org/show_bug.cgi?id=10807http://bugzilla.kernel.org/show_bug.cgi?id=10914
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
"idle=halt" limits the idle loop to using
the halt instruction. No MWAIT, no IO accesses,
no C-states deeper than C1.
If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
991528d734
(ACPI: Processor native C-states using MWAIT)
started passing C2C3_FFH to _PDC to tell the BIOS
that Linux supports MWAIT for deep C-states.
However, we should first double check with the hardware
that it actually supports MWAIT before potentially exposing
a BIOS bug of an MWAIT _CST on HW that doesn't support MWAIT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Synchronized tables with current specifications.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Fix bug in kernel_physical_mapping_init() that causes kernel
page table to be built incorrectly for systems with greater
than 512GB of memory.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using ACPI to find free address space allows us to find a gap for the
unallocated PCI resources or MMIO resources for hotplug devices within
the BIOS allowed PCI regions.
It works by evaluating the _CRS object under PCI0 looking for producer
resources. Then searches the e820 memory space for a gap within these
producer resources.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Dave Hansen reported a build error on 32bit which went unnoticed
as newer gcc versions seem to optimize unused static functions
away before compiling them.
Make vread_tsc() depend on CONFIG_X86_64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix merge fallout:
arch/x86/pci/amd_bus.c: In function ‘enable_pci_io_ecs':
arch/x86/pci/amd_bus.c:581: error: too many arguments to function ‘on_each_cpu'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add PCI ID for 6300ESB force hpet
x86: add another PCI ID for ICH6 force-hpet
kernel-paramaters: document pmtmr= command line option
acpi_pm clccksource: fix printk format warning
nohz: don't stop idle tick if softirqs are pending.
pmtmr: allow command line override of ioport
nohz: reduce jiffies polling overhead
hrtimer: Remove unused variables in ktime_divns()
hrtimer: remove warning in hres_timers_resume
posix-timers: print RT watchdog message
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
* 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, generic: mark early_printk as asmlinkage
printk: export console_drivers
printk: remember the message level for multi-line output
printk: refactor processing of line severity tokens
printk: don't prefer unsuited consoles on registration
printk: clean up recursion check related static variables
namespacecheck: more kernel/printk.c fixes
namespacecheck: fix kernel printk.c
* 'tracing/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (228 commits)
ftrace: build fix for ftraced_suspend
ftrace: separate out the function enabled variable
ftrace: add ftrace_kill_atomic
ftrace: use current CPU for function startup
ftrace: start wakeup tracing after setting function tracer
ftrace: check proper config for preempt type
ftrace: trace schedule
ftrace: define function trace nop
ftrace: move sched_switch enable after markers
ftrace: prevent ftrace modifications while being kprobe'd, v2
fix "ftrace: store mcount address in rec->ip"
mmiotrace broken in linux-next (8-bit writes only)
ftrace: avoid modifying kprobe'd records
ftrace: freeze kprobe'd records
kprobes: enable clean usage of get_kprobe
ftrace: store mcount address in rec->ip
ftrace: build fix with gcc 4.3
namespacecheck: fixes
ftrace: fix "notrace" filtering priority
ftrace: fix printout
...
John Keller reports that PCI config space access is broken on machines
with more than one domain. conf1 accesses only work for domain 0, so make sure
we check the domain number in the raw routines before trying conf1.
Reported-by: John Keller <jpk@sgi.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Explain that we set up the descriptors for Big Real Mode, and why we
do so. In particular, one system that is known to fail without it is
the Lenovo X61.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The explanation for recent video BIOS suspend quirk failures is that
the VESA BIOS expects to be entered in Big Real Mode (*.limit = 0xffffffff)
instead of ordinary Real Mode (*.limit = 0xffff).
This patch changes the segment descriptors to Big Real Mode instead.
The segment descriptor registers (what Intel calls "segment cache") is
always active. The only thing that changes based on CR0.PE is how it is
*loaded* and the interpretation of the CS flags.
The segment descriptor registers contain of the following sub-registers:
selector (the "visible" part), base, limit and flags. In protected mode
or long mode, they are loaded from descriptors (or fs.base or gs.base can
be manipulated directly in long mode.) In real mode, the only thing
changed by a segment register load is the selector and the base, where the
base <- selector << 4. In particular, *the limit and the flags are not
changed*.
As far as the handling of the CS flags: a code segment cannot be writable
in protected mode, whereas it is "just another segment" in real mode, so
there is some kind of quirk that kicks in for this when CR0.PE <- 0. I'm
not sure if this is accomplished by actually changing the cs.flags register
or just changing the interpretation; it might be something that is
CPU-specific. In particular, the Transmeta CPUs had an explicit "CS is
writable if you're in real mode" override, so even if you had loaded CS
with an execute-only segment it'd be writable (but not readable!) on return
to real mode. I'm not at all sure if that is how other CPUs behave.
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when try to make hpet_enable use io_remap instead fixmap got
ioremap: invalid physical address fed00000
------------[ cut here ]------------
WARNING: at arch/x86/mm/ioremap.c:161 __ioremap_caller+0x8c/0x2f3()
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.26-rc9-tip-01873-ga9827e7-dirty #358
Call Trace:
[<ffffffff8026615e>] warn_on_slowpath+0x6c/0xa7
[<ffffffff802e2313>] ? __slab_alloc+0x20a/0x3fb
[<ffffffff802d85c5>] ? mpol_new+0x88/0x17d
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8024b0d2>] __ioremap_caller+0x8c/0x2f3
[<ffffffff80e86dbd>] ? hpet_enable+0x39/0x241
[<ffffffff8022a4f4>] ? mcount_call+0x5/0x31
[<ffffffff8024b466>] ioremap_nocache+0x2a/0x40
[<ffffffff80e86dbd>] hpet_enable+0x39/0x241
[<ffffffff80e7a1f6>] hpet_time_init+0x21/0x4e
[<ffffffff80e730e9>] start_kernel+0x302/0x395
[<ffffffff80e722aa>] x86_64_start_reservations+0xb9/0xd4
[<ffffffff80e722fe>] ? x86_64_init_pda+0x39/0x4f
[<ffffffff80e72400>] x86_64_start_kernel+0xec/0x107
---[ end trace a7919e7f17c0a725 ]---
it seems for amd system that is set later...
try to move setting early in early_identify_cpu.
and remove same code for intel and centaur.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
only add direct mapping for aperture
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Strengthen the return type for the _node_to_cpumask_ptr to be
a const pointer. This adds compiler checking to insure that
node_to_cpumask_map[] is not changed inadvertently.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: "akpm@linux-foundation.org" <akpm@linux-foundation.org>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that IRQ2 is never made available to the I/O APIC, there is no need
to special-case it and mask as a workaround for broken systems. Actually,
because of the former, mask_IO_APIC_irq(2) is a no-op already.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
got this on a test-system:
calling numaq_tsc_disable+0x0/0x39
NUMAQ: disabling TSC
initcall numaq_tsc_disable+0x0/0x39 returned 0 after 0 msecs
that's because we should not be using arch_initcall to call numaq_tsc_disable.
need to call it in setup_arch before time_init()/tsc_init()
and call it in init_intel() to make the cpu feature bits right.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
end_user_pfn used to modify the meaning of the e820 maps.
Now that all e820 operations are cleaned up, unified, tightened up,
the e820 map always get updated to reality, we don't need to keep
this secondary mechanism anymore.
If you hit this commit in bisection it means something slipped through.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
