While processing get_station cfg operation, HDD is using Nss
value, which gets updated during association, to calculate data
rate. So, there is a possibility of driver to report invalid
MCS index to upper layer if association happens with Nss 2 and
when data transmission is happening at Nss 1 rate.
On receiving GET STATS response, calculate Nss value based upon
the current data rate received from firmware, and pass it to HDD,
so that HDD can use the same Nss value to report valid MCS index
to the upper layer.
Change-Id: I62f029d53149a4747f619027ce69ce65fb280b8d
CRs-Fixed: 2250993
Parse the association response frame to read the
peer TWT extended capabilities and fill them in
the WMI PEER ASSOC command and send it to the
firmware.
Change-Id: I07f21010abbdaa20e212abae127009dd11e6ab7d
CRs-Fixed: 2264690
Currently while going to suspend, dtim parameters are not
correctly getting configured. Some other parameters to config
like the inactivity timeout are completely skipped as well.
Cleanly port the setting of dtim and other parameters during
suspend and resume.
Change-Id: Ic41a8ace3f5650e53f2dcaa416bfe241b87aa88d
CRs-Fixed: 2248160
currently some HE capability is shared same value from
MIN value of 2G and 5G capability, separate them per band.
Change-Id: I37831b4044d4ca2deaf5015fb44227c824996136
CRs-Fixed: 2239070
Android Packet Filter 3.0 requires the framework to be able
to read and write into the APF work memory in the Firmware.
It also requires to be able to enable or disable the
interpreter.
Add support for the new read/write/enable/disable operations.
Change-Id: Ic72243b918f4a8385a92b803a1ca3c5305423b52
CRs-Fixed: 2184969
Add the compilation flags for TWT feature to Kbuild.
Based on the compilation flag, include the source
files for compilation and also include the header
files path.
Change-Id: I45991b3c9e49e2aa0ff51a2650fde69ea447bf15
CRs-Fixed: 2238302
Process the TWT enable complete event sent by the
firmware after enabling TWT.
Set the appropriate state for TWT so that it can
be used later to check if TWT is enabled or not
in the target.
Change-Id: I924387d6afc2bf80efec0fce36ea907c6932dcda
CRs-Fixed: 2238302
Send the WMI_TWT_ENABLE_CMDID command to the target if the target
supports any one mode out of requestor, responder or broadcast mode.
Change-Id: I7ab21fff89e7c88bf951b333d7a923857f2123d6
CRs-Fixed: 2238302
Introduce new WNI items for TWT as follows:
WNI_CFG_TWT_REQUESTOR
WNI_CFG_TWT_RESPONDER
WNI_CFG_BCAST_TWT
Based on the INI configuration and target support, enable
or disable the TWT services in the WNI CFG database.
Change-Id: Id1b239e53f30f00220e0cefb541fc641a898e712
CRs-Fixed: 2238302
The tSirRetStatus definitions are obsolete, so replace them with
QDF_STATUS definitions in the wma folder.
Change-Id: I3ba728e378697fb02f02322e7a467cd4f8a62c10
CRs-Fixed: 2262962
In implementation of Android Packet Filter, functions, variables,
definitions are named after BPF, which stands for Berkely Packet
Filter. The term was more appropriate for Link Layer packet
filters implemented in the Linux kernel, known as Linux Socket
Filters.
The term BPF is obsolete now, so rename it with the
appropriate acronym, APF.
Change-Id: I9e02edbc580ffb2c559c8e864f54d255fc2d51a3
CRs-Fixed: 2191530
PMO should not know about vdev data path handle, but
pmo_unpause_all_vdev() need it, so register a wma callback to retrieve
the vdev dp handle instead of keep a copy in pmo vdev private context.
Refine current code to retrieve vdev dp handle using a wma callback
Change-Id: I1f668fff633a5e5cdfc478e7f619e9600930b333
CRs-Fixed: 2227384
During a channel switch, host sends the beacon template to the FW.
Currently the CSA/ECSA Channel Switch count offset fields in the
WMI_BCN_TMPL_CMDID fixed params are not filled from the host.
Add changes to calculate the CSA/ECSA Switch count offset from
start of the beacon template data and fill it in the fixed
params field for WMI_BCN_TMPL_CMDID.
Change-Id: Icb568f59346972784c4aceef9b42c8543adaa889
CRs-Fixed: 2246600
Add support for getting cfg integer from PMO. Register callbacks
during pe_open/close so that PMO can query CFG int values for
calculating parameters like listen interval etc.
Change-Id: I52d165586576e547e175ba276e6b7225db5b27e0
CRs-Fixed: 2252661
Currently the function typedef wma_tgt_cfg_cb is defined with two void
pointer parameters. However the types of the two parameters are known
to both the sender and the receiver, so fully specify the types of
those parameters.
Change-Id: I7cf7178015084599061b123da7b5f1f453ec5353
CRs-Fixed: 2254954
Remove support for enabling/disabling SIFS burst mode,
SAP DFS channel SIFS burst and SIFS burst duration through
ini parameter as well as through IOCTL
Change-Id: I3d43afa3c0c85eef470a29b9e7ad812079666278
CRs-Fixed: 2238175
These board information are stored in the board file while the
calibration process. WMI service ready event will now carry them for host.
Append these board version information to the firmware version string.
Change-Id: Ieb5bc480bd0c2e387fcf6990dd192741f0b7cd6b
CRs-fixed: 2218963
Address the following issues in the core/wma folder:
CHECK: 'accomodate' may be misspelled - perhaps 'accommodate'?
CHECK: 'acess' may be misspelled - perhaps 'access'?
CHECK: 'catagory' may be misspelled - perhaps 'category'?
CHECK: 'chnage' may be misspelled - perhaps 'change'?
CHECK: 'defintions' may be misspelled - perhaps 'definitions'?
CHECK: 'Intialize' may be misspelled - perhaps 'Initialize'?
CHECK: 'Intial' may be misspelled - perhaps 'Initial'?
CHECK: 'proces' may be misspelled - perhaps 'process'?
CHECK: 'progess' may be misspelled - perhaps 'progress'?
CHECK: 'refrence' may be misspelled - perhaps 'reference'?
CHECK: 'Relevent' may be misspelled - perhaps 'Relevant'?
CHECK: 'reponse' may be misspelled - perhaps 'response'?
Change-Id: Idc314b5a3a6945211581e2135cfaf9d0d5f69457
CRs-Fixed: 2241946
Remove duplicate structs wmi_dual_mac_config and sir_dual_mac_config
and use policy_mgr_dual_mac_config.
Change-Id: I6da6539f519ec46ee274ba3f3ae042e5fd9c25d2
CRs-Fixed: 2190993
wma_is_service_enabled can't get valid service bitmap if call in
hdd_update_pmo_config, use psoc_ctx->caps.unified_wow instead to check
pattern id per vdev and legacy d0 wow capability.
Change-Id: If7bf316f482c49253fc4b95b94e172727b27ffd1
CRs-Fixed: 2225847
Move chanmode_to_chanwidth API to qcacmn since it will be used by ndp
schedule update event.
Change-Id: I13d00c0b818eb0da434c8a5372b2ab7b6693f22a
CRs-Fixed: 2216803
Add GRO support and make it configurable through INI(GROEnable).
GRO and LRO are mutually exclusive. Only one of them can be enabled.
And disable GRO during following conditions
1) Low TPUT scenario
2) Concurrency cases
3) For Rx packets when Peer is not connected
Change-Id: I15535827a03953231670d4138235c4876b16e045
CRs-Fixed: 2098772
CCMP and GCMP both have different lengths of their MIC part. MIC
length for CCMP is 8 bytes whereas it is 16 bytes for GCMP. When
encryption type is GCMP/GCMP-256, sending packets with CCMP MIC
length causes fw to drop the GCMP encrypted management packets
leading to connection issues.
Send GCMP encrypted frames with GCMP MIC length.
Change-Id: Ia83fa6ffde880fe69e5e4c3e3c3ce9c62ad8fa3c
CRs-Fixed: 2203224
Video/audio wireless application needs to tune parameters
per AC based. Config the number of TX sw retry per AC via
driver INI configuration file. It helps to improve the
video/audio performance in noisy environment.
Change-Id: Icffb5174b265b6453021b0d0a8ad3e12b695847a
CRs-Fixed: 2212954
Video/audio wireless application needs to tune parameters
per AC based. Configure A-MPDU subframe parameter per
AC via driver ini configuration file.
Change-Id: Id63be7aacf6465edee08f7a2f4c8a119f9bd6346
CRs-Fixed: 2212932
Add support to process MU EDCA param set in assoc response
frames and send the params to FW.
Change-Id: Ia492d1212b3c357647a89e4f98d3cfdc7ff7bbac
CRs-Fixed: 2220227
Fix condition checked before programming user's requested chainmask to
firwmare. Get current firmware advertised phy cap for non-dbs phymode
and check if it supports all chains for tx/rx 2g and 5g.
Change-Id: I3fcef315f478403955ce400b3ba6d138a8006a01
CRs-Fixed: 2202544
The SoftAP VSTA feature was introduced to overcome a limitation in a
prior version of WLAN hardware. Since the WLAN hardware supported by
this driver does not have this limitation, remove the feature code.
Change-Id: I1f2fe31b294fb7b2da1fa8619b3380412c5d872e
CRs-Fixed: 2224817
WMI cmds should be blocked, before calling HTC stop
to avoid the race condition in the system
Change-Id: I677c55cd96ea6af973595eec1e759641fbea109a
CRs-Fixed: 2193653
The driver contains considerable debris from the obsolete WOWL
messaging, so clean it up.
Change-Id: I432f7fc1567b0aa31a7be758c05f2213340baed0
CRs-Fixed: 2223859
qcacld-2.0 to qcacld-3.0 propagation
Discard the original wmi interface:
WMI_PEER_ANTDIV_INFO_REQ_CMDID/PEER_ANTDIV_INFO_EVENTID,
replace with the new one:
WMI_PDEV_DIV_GET_RSSI_ANTID_CMDID/WMI_PDEV_DIV_RSSI_ANTID_EVENTID
to support chain value along with corresponding antenna info.
Change-Id: Ie9ea9d160e1ac1e2e65de422c85989159fb5a556
CRs-Fixed: 2005820
Currently Kbuild unconditionally sets -DHAL_SELF_STA_PER_BSS=1. There
is only one place where this macro is referenced, and it actually
requires that the macro be set for the driver to work. Since this
logic isn't really conditional, remove the conditional compilation.
Change-Id: I09a03339df086146b81b3012fb281e166fccd5da
CRs-Fixed: 2221852
Currently a set of ANI_COMPILER_TYPE macros are checked against, but
other than that they serve no purpose. As part of ongoing Kbuild
cleanup remove these obsolete macros.
Change-Id: Ia112d7d5ae8d12eae46144b53addc8ad54393bba
CRs-Fixed: 2220285
The Data Path in the WLAN host driver needs to be sending DHCP START/
STOP indications to FW during DHCP based IP address acquisition phase
in the SAP mode.
Inspect the Tx/Rx frame, and send the notification to the FW through
WMI message.
Change-Id: Iad6308980a7158516f341b97f3baffab1e4c4bc3
CRs-Fixed: 2114816
IPA module has been moved to CLD component under the converged
driver model. Remove legacy WMA interface IPA command and use
the new defined API.
Change-Id: Icd9a207f43f8df4dc563d0078d402470683cfd7d
CRs-Fixed: 2177925
Move Channel convert and frame indication logic from lim_p2p.c
to lim_utils.c and remove unused timer
pMac->lim.limTimers.gLimP2pSingleShotNoaInsertTimer.
Change-Id: I71de90d5fb88462e52148a434d43ea80c41cfe36
CRs-Fixed: 2191282
In STA mode, tx params for auth and assoc req frame
are not updated if minrate is 1 or 6Mbps as these
are the default rates for 2.4G and 5G respectively.
If 2.4G APs min supported rate is 6Mbps, the tx params
are not updated which results in auth and assoc req
frame transmitted at 1Mbps.
Fix is to update tx params if minrate is 6Mbps and
AP is operating in 2.4G.
Change-Id: Ia12c7b13cfb93e2d3b5a4ae124003248fa109e3f
CRs-Fixed: 2205282
In a previous version of the driver both unicast and broadcast DPU
signatures were used to synchronize the data plane with the control
plane. However the current version of the driver does not use this
synchronization mechanism, so remove propagation of the DPU signatures
from the UMAC. This is part of the plan to completely remove these
signatures from throughout the driver.
Change-Id: I6a1808d0905bb0c4550b16cf2b2157a529caa9e9
CRs-Fixed: 2200997
