If one attempts to create a device driver recovery sequence that
does not depend on a hard reset of the device, but simply just
attempts to resume processing, then one discovers that the
recovery sequence implemented on powerpc is not quite right.
This patch fixes this up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing include in rom.c. Fixes this build error when CONFIG_MTD=y:
arch/powerpc/sysdev/rom.c:26: error: implicit declaration of function
of_platform_device_create
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Purely cosmetic. Change pSeries to pseries inline with other parts of the
kernel, and fix an overly long line.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To support cpu hotplug on pseries we require two RTAS tokens. The cpu
hotplug machinery should only be wired up if these tokens are found in
the device tree.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the rest of the hotplug cpu code from platforms/pseries/smp.c into
platforms/pseries/hotplug-cpu.c.
Wire up the smp_ops callbacks and the notifier in the hotplug cpu initcall,
rather than in smp_init_pseries(). No change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c,
this allows rtas_stop_self() to be static so remove the prototype.
Wire up pSeries_mach_cpu_die() in the initcall, rather than statically
in setup.c, the initcall will still run prior to the cpu hotplug code
being callable, so there should be no change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As the first step in consolidating the pseries hotplug cpu code,
create platforms/pseries/hotplug-cpu.c and move rtas_stop_self()
into it. Do the rtas token initialisation in a new initcall, rather
than rtas_initialize().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make sure that the pmu is not initialised unless we are running on a cell.
Also make the init routine static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The elf note saving code is currently duplicated over several
architectures. This cleanup patch simply adds code to a common file and
then replaces the arch-specific code with calls to the newly added code.
The only drawback with this approach is that s390 doesn't fully support
kexec-on-panic which for that arch leads to introduction of unused code.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we are unregistering a kprobe-booster, we can't release its
instruction buffer immediately on the preemptive kernel, because some
processes might be preempted on the buffer. The freeze_processes() and
thaw_processes() functions can clean most of processes up from the buffer.
There are still some non-frozen threads who have the PF_NOFREEZE flag. If
those threads are sleeping (not preempted) at the known place outside the
buffer, we can ensure safety of freeing.
However, the processing of this check routine takes a long time. So, this
patch introduces the garbage collection mechanism of insn_slot. It also
introduces the "dirty" flag to free_insn_slot because of efficiency.
The "clean" instruction slots (dirty flag is cleared) are released
immediately. But the "dirty" slots which are used by boosted kprobes, are
marked as garbages. collect_garbage_slots() will be invoked to release
"dirty" slots if there are more than INSNS_PER_PAGE garbage slots or if
there are no unused slots.
Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "bibo,mao" <bibo.mao@intel.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Yumiko Sugita <yumiko.sugita.yf@hitachi.com>
Cc: Satoshi Oshima <soshima@redhat.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Following up with the work on shared page table done by Dave McCracken. This
set of patch target shared page table for hugetlb memory only.
The shared page table is particular useful in the situation of large number of
independent processes sharing large shared memory segments. In the normal
page case, the amount of memory saved from process' page table is quite
significant. For hugetlb, the saving on page table memory is not the primary
objective (as hugetlb itself already cuts down page table overhead
significantly), instead, the purpose of using shared page table on hugetlb is
to allow faster TLB refill and smaller cache pollution upon TLB miss.
With PT sharing, pte entries are shared among hundreds of processes, the cache
consumption used by all the page table is smaller and in return, application
gets much higher cache hit ratio. One other effect is that cache hit ratio
with hardware page walker hitting on pte in cache will be higher and this
helps to reduce tlb miss latency. These two effects contribute to higher
application performance.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Dave McCracken <dmccr@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the 'no_control' field in the cpu struct to a more positive
and better term 'hotpluggable'. And change(/cleanup) the logic accordingly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Print the addresses of non-absolute symbols relative to _text
so that ld will generate relocations. Allowing a relocatable
kernel to relocate them. We can't actually use the symbol names
because kallsyms includes static symbols that are not exported
from their object files.
Add the _text symbol definitions to the architectures which don't
define it otherwise linker will fail.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
The support for the 52xx-based systems is now included under
CONFIG_CLASSIC32, since the 52xx chips have a 603e-based core.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a powerpc make target that can be loaded by the ps3 bootloader (kboot) and
set this as the default image to build for that platform.
Until the compressed zImage wrapper is made, this arranges for a stripped
vmlinux image to be built.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cure the damage done by the former PCI debug printks fix for the case
of 64-bit resources (commit 685143ac1f)
which broke it for the plain vanilla 32-bit resources...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the Kurobox(HG)/LinkStation-I NAS systems by Buffalo
Technology, should be also applicable to the PPC TeraStation family.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove CPU_FTR_16M_PAGE from the cupfeatures mask at runtime on iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon still does not run on iSeries, but this allows us to build a combined
kernel that includes it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Defconfig ppc64 kernels running under late-model distros
may hang in the automounter rc.d script, which seems to be
expecting autofs version 4. This patch uses the newer autofs.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the "logical" PVR value used by POWER6 in "compatible" mode
to the list of PVR values that the kernel tells firmware it is able to
handle.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a rule to clean up the various generated image files in
arch/powerpc/boot.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For PCI devices with only io ports, of_bus_pci_get_flags() will fall
through and still mark the resource as IORESOURCE_MEM.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds utility routines used by 52xx device drivers and board support
code. Main functionality is to add device nodes to the of_platform_bus,
retrieve the IPB bus frequency, and find+ioremap device registers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no need to expose these settings outside the scope
of the interrupt controller code itself.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Efika board isn't different enough from other 52xx based boards to
justify a separate platform. This patch merges it with the support
code for all other 52xx based boards.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
platforms/embedded6xx is probably going away, and 52xx boards need
some extra support the 52xx interrupt controller and DMA engine
anyway. It makes sense to group all the 52xx bits into a single path.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
No other chips use this device, it belongs in a 52xx-specific path.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It doesn't hurt to have this enabled on legacy iSeries and will mean it
is available for a combined build.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 3ccfc65c50 missed the same fixes for
legacy iSeries specific code, so make some more symbols no longer global.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly taken from corresponding Makefile's make-clean rule.
Tested by (cross)compiling for $ARCH PPC and POWERPC and checking
output of git-status.
Signed-off-by: Rutger Nijlunsing <git-commit@tux.tmfweb.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for flash device descriptions to the OF device tree.
It's inspired by and partially borrowed from Sergei's patch "[RFC]
Adding MTD to device tree.patch".
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows any secondary CPU thread also to become boot cpu for
POWER5. The patch is required to solve kdump boot issue when the
kdump kernel is booted with parameter "maxcpus=1". XICS init code
tries to match the current boot cpu id with "reg" property in each CPU
node in the device tree. But CPU node is created only for primary
thread CPU ids and "reg" property only reflects primary CPU ids. So
when a kernel is booted on a secondary cpu thread above condition will
never meet and the default distribution server is left as zero. This
leads to route the interrupts to CPU 0, but which is not online at
this time.
We use ibm,ppc-interrupt-server#s to check for both primary and
secondary CPU ids. Accordingly default distribution server value is
initialized from "ibm,ppc-interrupt-gserver#s" property. We loop
through ibm,ppc-interrupt-gserver#s property to find the global
distribution server from the last entry that matches with boot cpuid.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's currently not possible to build the default zImage
target if PS3 is the only selected platform. This is
a hack to fall back to building the pseries style
zImage, so the build is successful. This will probably
change in the future, if someone writes a PS3 specific
boot wrapper.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.
Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.
The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When renaming CONFIG_PS3 to CONFIG_PPC_PS3, a few occurrences have been
missed.
I also fixed up the alignment in arch/powerpc/platforms/Makefile.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It may be desireable to build a kernel for cell without
spufs, e.g. as the initial kboot kernel. This requires
that the SPU specific parts of the core dump and the xmon
code depend on CONFIG_SPU_BASE instead of CONFIG_PPC_CELL.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Currently, we only send a sigtrap if the current task is being ptraced.
This is somewhat inconsistant, and it breaks utrace support in fedora.
Removing the check should do the right thing in all cases.
Cc: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This changes the spu_create system call to return an error (-ENODEV) if
and isolated spu context is requested on hardware that doesn't support
isolated mode.
Tested on systemsim with and without isolation support
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch fixes a compile issue for the Efika platform recently
introduced by API changes.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the oprofile_cpu_type in cputables.c to be ppc64/970MP. Oprofile
needs to distinquish the MP from other 970 processors so it can add some
new counters specific to the 970MP.
Signed-off-by: Mike Wolf <mjw@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the common cell kernel, I want to have ps3 enabled
to find potential bugs at compile-time.
Also enable SPU disassembly in xmon.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds a ps3_defconfig for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds spu support for the PS3 platform.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds support for early access to the parameter data from the PS3 'Other OS'
flash memory area. The parameter data mainly holds user preferences like
static ip address.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds some needed bits for a config option PS3_USE_LPAR_ADDR that disables
the PS3 lpar address translation mechanism. This is a currently needed
workaround for limitations in the design of the generic cell spu support.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds the core platform support for the PS3 game console and other devices
using the PS3 hypervisor.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This fixes the xmon support for the cell spu to be compatable with the split
spu platform code.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This adds a platform specific spu management abstraction and the coresponding
routines to support the IBM Cell Blade. It also removes the hypervisor only
resources that were included in struct spu.
Three new platform specific routines are introduced, spu_enumerate_spus(),
spu_create_spu() and spu_destroy_spu(). The underlying design uses a new
type, struct spu_management_ops, to hold function pointers that the platform
setup code is expected to initialize to instances appropriate to that platform.
For the IBM Cell Blade support, I put the hypervisor only resources that were
in struct spu into a platform specific data structure struct spu_pdata.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This includes:
* version 1.24 of ppc-dis.c
* version 1.88 of ppc-opc.c
* version 1.23 of ppc.h
I can't vouch for the accuracy etc. of these changes, but it brings
us into line with binutils - and from a cursory test appears to work
fine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
While adding spu disassembly support it struck me that we're actually
carrying quite a lot of code around, just to do disassembly in the case
of a crash.
While on large systems it's not an issue, on smaller ones it might be
nice to have xmon - but without the weight of the disassembly support.
For a Cell build this saves ~230KB (!), and for pSeries ~195KB.
We still support the 'di' and 'sdi' commands, however they just dump
the instruction in hex.
Move the definitions into a header to clean xmon.c just a tiny bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds a "sdi" command to xmon, to disassemble the contents
of an spu's local store.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch imports and munges the spu disassembly code from binutils.
All files originated from version 1.1 in binutils cvs.
* spu.h, spu-insns.h and spu-opc.c are unchanged except for pathnames.
* spu-dis.c has been edited heavily:
* use printf instead of info->fprintf_func and similar.
* pass the instruction in rather than reading it.
* we have no equivalent to symbol_at_address_func, so we just assume
there is never a symbol at the address given.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
In order to do disassembly of spu binaries in xmon, we need to abstract
the disassembly function from ppc_inst_dump.
We do this by making the actual disassembly function a function pointer
that we pass to ppc_inst_dump(). To save updating all the callers, we
turn ppc_inst_dump() into generic_inst_dump() and make ppc_inst_dump()
a wrapper which always uses print_insn_powerpc().
Currently we pass the dialect into print_insn_powerpc(), but we always
pass 0 - so just make it a local.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Add a command to xmon to dump the memory of a spu's local store.
This mimics the 'd' command which dumps regular memory, but does
a little hand holding by taking the user supplied address and
finding that offset in the local store for the specified spu.
This makes it easy for example to look at what was executing on a spu:
1:mon> ss
...
Stopped spu 04 (was running)
...
1:mon> sf 4
Dumping spu fields at address c0000000019e0a00:
...
problem->spu_npc_RW = 0x228
...
1:mon> sd 4 0x228
d000080080318228 01a00c021cffc408 4020007f217ff488 |........@ ..!...|
Aha, 01a00c02, which is of course rdch $2,$ch24 !
--
Updated to only do the setjmp goo around the spu access, and not
around prdump because it does its own (via mread).
Also the num variable is now common between sf and sd, so you don't
have to keep typing the spu number in if you're repeating commands
on the same spu.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
After stopping spus in xmon I often find myself trawling through the
field dumps to find out which spus were running. The spu stopping
code actually knows what's running, so let's print it out to save
the user some futzing.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
My patch to add spu helpers to xmon (a898497088)
introduced a few sparse warnings, because I was dereferencing an __iomem
pointer.
I think the best way to handle it is to actually use the appropriate in_beXX
functions. Need to rejigger the DUMP macro a little to accomodate that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
With soft-disabled interrupts in power_save, we can
still get external exceptions on Cell, even if we are
in pause(0) a.k.a. sleep state.
When the CPU really wakes up through the 0x100 (system reset)
vector, while we have already started processing the 0x500
(external) exception, we get a panic in unrecoverable_exception()
because of the lost state.
This occurred in Systemsim for Cell, but as far as I can see,
it can theoretically occur on any machine that uses the
system reset exception to get out of sleep state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds SPU elf notes to the coredump. It creates a separate note
for each of /regs, /fpcr, /lslr, /decr, /decr_status, /mem, /signal1,
/signal1_type, /signal2, /signal2_type, /event_mask, /event_status,
/mbox_info, /ibox_info, /wbox_info, /dma_info, /proxydma_info, /object-id.
A new macro, ARCH_HAVE_EXTRA_NOTES, was created for architectures to
specify they have extra elf core notes.
A new macro, ELF_CORE_EXTRA_NOTES_SIZE, was created so the size of the
additional notes could be calculated and added to the notes phdr entry.
A new macro, ELF_CORE_WRITE_EXTRA_NOTES, was created so the new notes
would be written after the existing notes.
The SPU coredump code resides in spufs. Stub functions are provided in the
kernel which are hooked into the spufs code which does the actual work via
register_arch_coredump_calls().
A new set of __spufs_<file>_read/get() functions was provided to allow the
coredump code to read from the spufs files without having to lock the
SPU context for each file read from.
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Devices with no "reg" nor "dcr-reg" property are given a bus_id which
is the node name alone. This means that if more than one such device
with the same names are present in the system, sysfs will have
collisions when creating the symlinks and will fail registering the
devices.
This works around that problem by assigning successive numbers to such
devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following routines are added to arch/powerpc/platforms/cell/pmu.c:
cbe_clear_pm_interrupts()
cbe_enable_pm_interrupts()
cbe_disable_pm_interrupts()
cbe_query_pm_interrupts()
cbe_pm_irq()
cbe_init_pm_irq()
This also adds a routine in arch/powerpc/platforms/cell/interrupt.c and
some macros in cbe_regs.h to manipulate the IIC_IR register:
iic_set_interrupt_routing()
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some PMU-related macros and function prototypes from cbe_regs.h
and pmu.h in arch/powerpc/platforms/cell/ to a new header at
include/asm-powerpc/cell-pmu.h
This is cleaner to use from the oprofile code, since that sits in
arch/powerpc/oprofile, not in the cell platform directory.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More macros for manipulating bits in the Cell PMU control registers.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add symbol-exports for the new routines in arch/powerpc/platforms/cell/pmu.c.
They are needed for Oprofile, which can be built as a module.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to fit with the "don't-run-spus-outside-of-spu_run" model, this
patch starts the isolated-mode loader in spu_run, rather than
spu_create. If spu_run is passed an isolated-mode context that isn't in
isolated mode state, it will run the loader.
This fixes potential races with the isolated SPE app doing a
stop-and-signal before the PPE has called spu_run: bugzilla #29111.
Also (in conjunction with a mambo patch), this addresses #28565, as we
always set the runcntrl register when entering spu_run.
It is up to libspe to ensure that isolated-mode apps are cleaned up
after running to completion - ie, put the app through the "ISOLATE EXIT"
state (see Ch11 of the CBEA).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change adds a read accessor for the SPE problem-state run control
register.
This is required for for applying (userspace) changes made to the run
control register while the SPE is stopped - simply asserting the master
run control bit is not sufficient. My next patch for isolated-mode
setup requires this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the user changes the runcontrol register, an SPU might be
running without a process being attached to it and waiting for
events. In order to prevent this, make sure we always disable
the priv1 master control when we're not inside of spu_run.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When fixing spufs to map the 'mem' file backing store cacheable,
I incorrectly set the physical mapping to use both cache-inhibited
and guarded mapping, which resulted in a serious performance
degradation.
Debugged-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When one of the spufs files is mapped into a process address
space, regular users can use ptrace to attempt accessing
them with access_process_vm(). With the way that the
mappings currently work, this likely causes an oops.
Setting the vm_flags to VM_IO makes sure that ptrace can
not access them but returns an error code. This is not
the perfect solution in case of the local store mapping,
but it fixes the oops in a well-defined way.
Also remove leftover VM_RESERVED flags in spufs. The
VM_RESERVED flag is on it's way out and not checked by
the memory managment code anymore.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Christoph Hellwig <chellwig@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When there is pending signals, current spufs_run_spu() always returns
-ERESTARTSYS and it is called again automatically.
But, if spe already stopped by stop-and-signal or halt instruction,
returning -ERESTARTSYS makes stop-and-signal/halt lost and
spu run over the end-point.
For your convenience, I attached a sample code to restage this bug.
If there is no bug, printed NPC will be 0x4000.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we attempt an MFC DMA to an unmapped address, the event
returned from spu_run should be SPE_EVENT_SPE_DATA_STORAGE,
not SPE_EVENT_INVALID_DMA.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the use of the platform specific variable spu.nid with the
platform independednt variable spu.node.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to check the channel count of the signal notification registers
before reading them, because it can be undefined when the count is
zero. In order to read count and data atomically, we read from the
saved context.
This patch uses spu_acquire_saved() to force a context save before a
/signal1 or /signal2 read. Because of this it is no longer necessary to
have backing_ops and hw_ops versions of this function so they have been
removed.
Regular applications should not rely on reading this register
to be fast, as it's conceptually a write-only file from the PPE
perspective.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements read only access to
/mbox_info - SPU Write Outbound Mailbox
/ibox_info - SPU Write Outbound Interrupt Mailbox
/wbox_info - SPU Read Inbound Mailbox
These files are used by gdb in order to look into the current mailbox
queues without changing the contents at the same time. They are
not meant for general programming use, since the access requires
a context save and is therefore rather slow.
It would be good to complement this patch with one that adds
write support as well.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the /spu_tag_mask file from spufs. The data provided by
this file is also available from the /dma_info file in the dma_info_mask
of the spu_dma_info struct.
The file was intended to be used by gdb, but that never used it, and
now it has been replaced with the more verbose dma_info file.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The /lslr file gives read access to the SPU_LSLR register in hex; 0x3fff
for example The /dma_info file provides read access to the SPU Command
Queue in a binary format. The /proxydma_info files provides read access
access to the Proxy Command Queue in a binary format. The spu_info.h
file provides data structures for interpreting the binary format of
/dma_info and /proxydma_info.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches changes /npc, /decr, /decr_status, /spu_tag_mask,
/event_mask, /event_status, and /srr0 files to provide output according to
the format string "0x%llx" instead of "%llx".
Before this patch some files used "0x%llx" and other used "%llx" which is
inconsistent and potentially confusing. A user might assume "%llx" numbers
were decimal if they happened to not contain any a-f digits. This change
will break any code cannot tolerate a leading 0x in the file contents. The
only known users of these files are the libspe but there might also be
some scripts which access these files. This risk is deemed acceptable for
future consistency.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/mpc52xx_pic.c breaks the ppc build
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch below fixes an arithmetic wrap-around issue on 32bit machines
using smp-tbsync. Without this patch a timebase value over
0x000000007fffffff will hang the boot process while bringing up
secondary CPUs.
Signed-off-by: Adrian Cox <adrian@humboldt.co.uk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 2 changes to clean up the flat device tree handling
logic in the zImage wrapper.
First, there were two callbacks from the dt_ops structure used for
producing a final flat tree to pass to the kerne: dt_ops.ft_pack()
which packed the flat tree (possibly a no-op) and dt_ops.ft_addr()
which retreived the address of the final blob. Since they were only
ever called together, this patch combines the two into a single new
callback, dt_ops.finalize(). This new callback does whatever
platform-dependent things are necessary to produce a final flat device
tree blob, and returns the blob's addres.
Second, the current logic calls the kernel with a flat device tree if
one is build into the zImage wrapper, otherwise it boots the kernel
with a PROM pointer, expecting the kernel to copy the OF device tree
itself. This approach precludes the possibility of the platform
wrapper code building a flat device tree from whatever
platform-specific information firmware provides. Thus, this patch
takes the more sensible approach of invoking the kernel with a flat
tree if the dt_ops.finalize callback provides one (by whatever means).
So, the dt_ops.finalize callback can be NULL, or can be a function
which returns NULL. In either case, the zImage wrapper logic assumes
that this is a platform with OF and invokes the kernel accordingly.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the handling of the initrd (or initramfs) in the
zImage wrapper a little easier to follow. Instead of passing the
initrd addresses out from prep_kernel() via the cryptic a1 and a2
parameters, use the global struct add_range, 'initrd'. prep_kernel()
already passes information through the 'vmlinux' addr_range struct, so
this seems like a reasonable extension.
Some comments also clarify the logic with prep_kernel(): we use an
initrd included in the zImage if present, otherwise we use an initrd
passed in by the bootloader in the a1 and a2 parameters (yaboot, at
least, uses this mechanism to pass an initrd).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch adds a tsi108/9 pci interrupt controller host.
On mpc7448hpc2 board, pci_irq_fixup function is removed, which makes the
pci_read_irq_line be the default pci irq fixup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rewrite local_get_flags and local_irq_disable to use r13 explicitly,
to avoid the risk that gcc will split get_paca()->soft_enabled into a
sequence unsafe against preemption. Similar care in local_irq_restore.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge 32 and 64 bits asm-powerpc/io.h
The rework on io.h done for the new hookable accessors made it easier,
so I just finished the work and merged 32 and 64 bits io.h for arch/powerpc.
arch/ppc still uses the old version in asm-ppc, there is just too much gunk
in there that I really can't be bothered trying to cleanup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to suppose platforms with devices above 4Gb on 32 bits platforms
with a >32 bits physical address space, we used to have a special ioremap64
along with a fixup routine fixup_bigphys_addr.
This shouldn't be necessary anymore as struct resource now supports 64 bits
addresses even on 32 bits archs. This patch enables that option when
CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr.
This is a preliminary work for the upcoming merge of 32 and 64 bits io.h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that the direct DMA ops supports an offset, we use that instead
of defining our own.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes dma_alloc_coherent() use node local allocation when
using the direct DMA ops. The node is obtained from the new device
extension. If no such extension is present, the current node is used.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds an optional global offset that can be added to DMA addresses
when using the direct DMA operations.
That brings it a step closer to the 32 bits direct DMA operations, and makes
it useable on Cell when the MMU is disabled and we are using a spider
southbridge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements a workaround for a Spider PCI host bridge bug
where it doesn't enforce some of the PCI ordering rules unless some
manual manipulation of a special register is done. In order to be
fully compliant with the PCI spec, I do this on every MMIO read
operation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).
While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).
A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).
Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.
In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)
Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.
The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the Cell DMA code work on both the Spider and the Axon
south bridges by turning cell_dma_valid into a variable instead of a
constant. This is a temporary patch until we have full iommu support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a "parent" struct device to our PCI host bridge data structure so that
PCI can be rooted off another device in sysfs.
Note that arch/ppc doesn't use it, only arch/powerpc, though it's available
for both 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The BUID is the first entry of a PCI host bridge "reg" property.
Now that PCI busses can be anywhere in the device-tree, we need to
fully translate the value there to a CPU physical address before
we can use it with RTAS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When parsing the OF "ranges" properties of PCI host busses to determine
the mapping of a PCI bus, we need to translate the "parent" address using
the prom_parse.c routines in order to obtain a CPU physical address.
This wasn't necessary while PCI busses were always at the root of the
device-tree but this is no longer the case on Cell where they can be
anywhere in the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a bus device notifier to the of_platform bus type on
cell to setup the DMA operations for of_platform_devices. We currently
use the PCI operations as Cell use a special version of them that
happens to be suitable for our needs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hook up of_platform_bus_probe with the cell platform in order to publish
the non-PCI devices in the device-tree of cell blades as of_platform_device(s)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for southbridges using the MPIC interrupt controller to
the native cell platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch applies on top of the MPIC DCR support. It makes the MPIC
driver capable of a lot more auto-configuration based on the device-tree,
for example, it can retreive it's own physical address if not passed as
an argument, find out if it's DCR or MMIO mapped, and set the BIG_ENDIAN
flag automatically in the presence of a "big-endian" property in the
device-tree node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements support for DCR based MPIC implementations. Such
implementations have the MPIC_USES_DCR flag set and don't use the phys_addr
argument of mpic_alloc (they require a valid dcr mapping in the device node)
This version of the patch can use a little bif of cleanup still (I can
probably consolidate rb->dbase/doff, at least once I'm sure on how the
hardware is actually supposed to work vs. possible simulator issues) and
it should be possible to build a DCR-only version of the driver. I need
to cleanup a bit the CONFIG_* handling for that and probably introduce
CONFIG_MPIC_MMIO and CONFIG_MPIC_DCR.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These were inherited from ARCH=ppc, but are not needed since parsing of interrupts
should be done via the of_* functions (who can do swizzling). If we ever need to
do non-standard swizzling on bridges without a device-node, then we might add
back a slightly different version of ppc_md.pci_swizzle but for now, that is not
the case.
I removed the couple of calls for these in 83xx. If that breaks something, then
there is a problem with the device-tree on these.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This file no longer uses pci_cache_line_size, so delete the declaration
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
mpc832x, as in mpc8360, needs to explicitly find and create the
platform device for ucc_geth in 2.6.19. This code will likely be
readapted to Benh's new of_ methods for 2.6.20.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(David:)
If hugetlbfs_file_mmap() returns a failure to do_mmap_pgoff() - for example,
because the given file offset is not hugepage aligned - then do_mmap_pgoff
will go to the unmap_and_free_vma backout path.
But at this stage the vma hasn't been marked as hugepage, and the backout path
will call unmap_region() on it. That will eventually call down to the
non-hugepage version of unmap_page_range(). On ppc64, at least, that will
cause serious problems if there are any existing hugepage pagetable entries in
the vicinity - for example if there are any other hugepage mappings under the
same PUD. unmap_page_range() will trigger a bad_pud() on the hugepage pud
entries. I suspect this will also cause bad problems on ia64, though I don't
have a machine to test it on.
(Hugh:)
prepare_hugepage_range() should check file offset alignment when it checks
virtual address and length, to stop MAP_FIXED with a bad huge offset from
unmapping before it fails further down. PowerPC should apply the same
prepare_hugepage_range alignment checks as ia64 and all the others do.
Then none of the alignment checks in hugetlbfs_file_mmap are required (nor
is the check for too small a mapping); but even so, move up setting of
VM_HUGETLB and add a comment to warn of what David Gibson discovered - if
hugetlbfs_file_mmap fails before setting it, do_mmap_pgoff's unmap_region
when unwinding from error will go the non-huge way, which may cause bad
behaviour on architectures (powerpc and ia64) which segregate their huge
mappings into a separate region of the address space.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new 'wrapper' code generates files that git should ignore;
add them to .gitignore.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a check for a null ppc_md.init_early to allow platforms that
don't require an init_early routine to just set this member to null.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The qe_brg structure manually defined each of the 16 BRG registers, which
made any code that used them cumbersome. This patch replaces the fields
with a single 16-element array.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix compile warnings with CONFIG_PM=n
arch/powerpc/platforms/powermac/feature.c:489: warning: 'save_gpio_levels' defined but not used
arch/powerpc/platforms/powermac/feature.c:490: warning: 'save_gpio_extint' defined but not used
arch/powerpc/platforms/powermac/feature.c:491: warning: 'save_gpio_normal' defined but not used
arch/powerpc/platforms/powermac/feature.c:492: warning: 'save_unin_clock_ctl' defined but not used
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper Makefile does not clean up the 'zImage' file that
may be left laying around. This patch removes it when cleaning that
directory.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the wrapper script is passed a dts file, it runs 'dtc' to create
a dtb file. This patch deletes that dtb file once its no longer needed.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
bad_page_fault() prints a message telling the user what type of bad
fault we took. The first line of this message is currently implemented
as two separate printks. This has the unfortunate effect that if
several cpus simultaneously take a bad fault, the first and second parts
of the printk get jumbled up, which looks dodge and is hard to read.
So do a single one-line printk for each fault type.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Cleaned up interrupt mapping a little by adding a helper
function which parses the irq out of the device-tree, and puts
it into a resource.
* Changed the arch/ppc platform files to specify PHY_POLL, instead of -1
* Changed the fixed phy to use PHY_IGNORE_INTERRUPT
* Added ethtool.h and mii.h to phy.h includes
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add Efika (http://www.bplan-gmbh.de/efika_spec_en.html) platform
support for arch/powerpc.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for the MPC52xx Interrupt controller for
ARCH=powerpc.
It includes the main code in arch/powerpc/sysdev/ as well as a header
file in include/asm-powerpc.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make nvram_64.o dependent on 64bit, not on MULTIPLATFORM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dev_t boot_dev is declared in arch/powerpc/kernel/setup_32.c
and in arch/powerpc/kernel/setup_64.c but not used in these files.
It is only used in arch/powerpc/platforms/powermac/setup.c, so make
it static in this file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current cell processor support needs sparsemem, so set it as
the default memory model.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a typo in the "new style" code for mapping SPE resources,
which causes it to try to map the same resource 4 times.
It also adds some pr_debug's that are useful to track down issues with
the firmware when bringinh up new machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The enablement of 64k pages on pseries platforms exposed a bug in
the RTAS mechanism for updating firmware. RTAS assumes 4k for flash
block and list sizes, and use of any other sizes results in a failure,
even though PAPR does not specify any such requirement.
This patch changes the rtas_flash module to force the use of 4k memory
block and list sizes when preparing and sending a firmware image to
RTAS. The rtas_flash function now uses a slab cache of 4k blocks with
4k alignment, rather than get_zeroed_page(), to allocate the memory for
the flash blocks and lists. The 4k alignment requirement is specified
in PAPR.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The "wrapper" script was using the wrong names for the initrd and
dtb (device-tree blob) sections. This fixes it, and also ensures
the symbols for the start and end of the dtb get defined correctly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out that the linker warnings on 64-bit powerpc about "section
blah exceeds stub group size" were being triggered by conditional
branches in head_64.S branching to global symbols, whether in
head_64.S or in other files. This eliminates the warnings by making
some global symbols in head_64.S no longer global, and by rearranging
some branches.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[ Yee-haa. Maybe I'll notice newly introduced real warnings now - Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The alignment exception used to only check the exception table for
-EFAULT, not for other errors. That opens an oops window if we can
coerce the kernel into getting an alignment exception for other reasons
in what would normally be a user-protected accessor, which can be done
via some of the futex ops. This fixes it by always checking the
exception tables.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On powerpc, probing on emulate_step function will crash 2.6.18.1 when
it is triggered.
When kprobe is triggered, emulate_step() is on its kernel path and
will cause recursive kprobe fault. And branch_taken() is called
in emulate_step(). This disallows kprobes on both of them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Checking source for other get_paca()->field preemption dangers found that
open_high_hpage_areas does a structure copy into its paca while preemption
is enabled: unsafe however gcc accomplishes it. Just remove that copy:
it's done safely afterwards by on_each_cpu, as in open_low_hpage_areas.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed qe_issue_cmd() to write cmd_input to the CECDR unmodified. It
was treating cmd_input as a virtual address and tried to convert it to
a physical address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 10Gigabit ethernet device drivers appear to be able to chew
up all 256MB of TCE mappings on pSeries systems, as evidenced by
numerous error messages:
iommu_alloc failed, tbl c0000000010d5c48 vaddr c0000000d875eff0 npages 1
Some experimentation indicates that this is essentially because
one 1500 byte ethernet MTU gets mapped as a 64K DMA region when
the large 64K pages are enabled. Thus, it doesn't take much to
exhaust all of the available DMA mappings for a high-speed card.
This patch changes the iommu allocator to work with its own
unique, distinct page size. Although the patch is long, its
actually quite simple: it just #defines a distinct IOMMU_PAGE_SIZE
and then uses this in all the places that matter.
As a side effect, it also dramatically improves network performance
on platforms with H-calls on iommu translation inserts/removes (since
we no longer call it 16 times for a 1500 bytes packet when the iommu HW
is still 4k).
In the future, we might want to make the IOMMU_PAGE_SIZE a variable
in the iommu_table instance, thus allowing support for different HW
page sizes in the iommu itself.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.
* Reorganized FSL Book-E performance monitoring code so that the 7450
wouldn't be built if the e500 was, and cleaned it up so it was more
self-contained.
* Added a cpu_setup function for FSL Book-E. The original
cpu_setup function prototype had no arguments, assuming that
the reg_setup function would copy the required information into
variables which represented the registers. This was silly for
e500, since it has 1 register per counter (rather than 3 for
all counters), so the code has been restructured to have
cpu_setup take the current counter config array as an argument,
with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
on_each_cpu(), and op_powerpc_cpu_setup() invoking the
model-specific cpu_setup function with an argument. The
argument is ignored on all other platforms at present.
* Fixed a confusing line where a trinary operator only had two
arguments
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a few issues in offb:
- A test was inverted causing the palette hack to never work
(no device node was passed down to the init function)
- Some cards seem to have their assigned-addresses property in a random
order, thus we need to try using of_get_pci_address() first, which will
fail if it's not a PCI device, and fallback to of_get_address() in that
case. of_get_pci_address() properly parsees assigned-addresses to test
the BAR number and thus will get it right whatever the order is.
- Some cards (like GXT4500) provide a linebytes of 0xffffffff in the
device-tree which does no good. This patch handles that by using the
screen width when that happens. (Also fixes btext.c while at it).
- Add detection of the GXT4500 in addition to the GXT2000 for the
palette hacks (we use the same hack, palette is linear in register space
at offset 0x6000).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a cpufreq backend driver to enable frequency scaling on cell.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a command to xmon for dumping information about
spu structs. The command is 'sf' for "spu fields" perhaps, and
takes the spu number as an argument. This is the same value as the
spu->number field, or the "phys-id" value of a context when it is
bound to a physical spu.
We try to catch memory errors as we dump each field, hopefully this
will make the command reasonably robust, but YMMV. If people see a
need we can easily add more fields to the dump in future.
Output looks something like this:
0:mon> sf 0
Dumping spu fields at address c00000001ffd9e80:
number = 0x0
name = spe
devnode->full_name = /cpus/PowerPC,BE@0/spes/spe@0
nid = 0x0
local_store_phys = 0x20000000000
local_store = 0xd0000800801e0000
ls_size = 0x0
isrc = 0x4
node = 0x0
flags = 0x0
dar = 0x0
dsisr = 0x0
class_0_pending = 0
irqs[0] = 0x16
irqs[1] = 0x17
irqs[2] = 0x24
slb_replace = 0x0
pid = 0
prio = 0
mm = 0x0000000000000000
ctx = 0x0000000000000000
rq = 0x0000000000000000
timestamp = 0x0000000000000000
problem_phys = 0x20000040000
problem = 0xd000080080220000
problem->spu_runcntl_RW = 0x0
problem->spu_status_R = 0x0
problem->spu_npc_RW = 0x0
priv1 = 0xd000080080240000
priv1->mfc_sr1_RW = 0x33
priv2 = 0xd000080080250000
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for stopping, and restarting, spus
from xmon. We use the spu master runcntl bit to stop execution,
this is apparently the "right" way to control spu execution and
spufs will be changed in the future to use this bit.
Testing has shown that to restart execution we have to turn the
master runcntl bit on and also rewrite the spu runcntl bit, even
if it is already set to 1 (running).
Stopping spus is triggered by the xmon command 'ss' - "spus stop"
perhaps. Restarting them is triggered via 'sr'. Restart doesn't
start execution on spus unless they were running prior to being
stopped by xmon.
Walking the spu->full_list in xmon after a panic, would mean
corruption of any spu struct would make all the others
inaccessible. To avoid this, and also to make the next patch
easier, we cache pointers to all spus during boot.
We attempt to catch and recover from errors while stopping and
restarting the spus, but as with most xmon functionality there are
no guarantees that performing these operations won't crash xmon
itself.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the cell idle function to use the default cpu_idle
with a special power_save callback, like all other platforms
except iSeries already do.
It also makes it possible to disable this power_save function
with a new powerpc-specific boot option "powersave=off".
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a module that registers sysfs attributes to CPU and SPU
containing the temperature of the CBE.
They can be found under
/sys/devices/system/spu/cpuX/thermal/temperature[0|1]
/sys/devices/system/spu/spuX/thermal/temperature
The temperature is read from the on-chip temperature sensors.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds two functions to create and remove sysfs attributes and
attribute_group to all cpus. That allows to register sysfs attributes in
a subdirectory like: /sys/devices/system/cpu/cpuX/group_name/what_ever
This will be used by cbe_thermal to group all attributes dealing with
thermal support in one directory.
Signed-of-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to add sysfs attributes to all spu's, there is a
need for a list of all available spu's. Adding the device_node
makes also sense, as it is needed for proper register access.
This patch also adds two functions to create and remove sysfs
attributes and attribute_groups to all spus.
That allows to group spu attributes in a subdirectory like:
/sys/devices/system/spu/spuX/group_name/what_ever
This will be used by cbe_thermal to group all attributes dealing with
thermal support in one directory.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add routines for accessing the registers and counters in the performance
monitoring unit.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many of the registers in the performance monitoring unit are write-only.
We need to save a "shadow" copy when we write to those registers so we
can retrieve the values if we need them later.
The new cbe_pmd_shadow_regs structure is added to the cbe_regs_map structure
so we have the appropriate per-node copies of these shadow values.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are a few definitions that are required by subsequent patches,
so add them here.
The original patch is from David Erb, but is significantly cleaned
up by Kevon Corry.
Cc: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When in isolated mode, SPEs have access to an area of persistent
storage, which is per-SPE. In order for isolated-mode apps to
communicate arbitrary data through this storage, we need to ensure that
isolated physical SPEs can be reused for subsequent applications.
Add a file ("recycle") in a spethread dir to enable isolated-mode
recycling. By writing to this file, the kernel will reload the
isolated-mode loader kernel, allowing a new app to be run on the same
physical SPE.
This requires the spu_acquire_exclusive function to enforce exclusive
access to the SPE while the loader is initialised.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds general support for isolated mode SPE apps.
Isolated apps are started indirectly, by a dedicated loader "kernel".
This patch starts the loader when spe_create is invoked with the
ISOLATE flag. We do this at spe_create time to allow libspe to pass the
isolated app in before calling spe_run.
The loader is read from the device tree, at the location
"/spu-isolation/loader". If the loader is not present, an attempt to
start an isolated SPE binary will fail with -ENODEV.
Update: loader needs to be correctly aligned - copy to a kmalloced buf.
Update: remove workaround for systemsim/spurom 'L-bit' bug, which has
been fixed.
Update: don't write to runcntl on spu_run_init: SPU is already running.
Update: do spu_setup_isolated earlier
Tested on systemsim.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds two new flags to spu_create:
SPU_CREATE_NONSCHED: create a context that is never moved
away from an SPE once it has started running. This flag
can only be used by tasks with the CAP_SYS_NICE capability.
SPU_CREATE_ISOLATED: create a nonschedulable context that
enters isolation mode upon first run. This requires the
SPU_CREATE_NONSCHED flag.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the mostly unused variable isrc from struct spu and a forgotten
function declaration.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SPRN_SDR1 and the SPE's MFC SDR are hypervisor resources and
are not accessible from a logical partition. This change adds an
access wrapper.
When running on bare H/W, the spufs needs to only set the SPE's MFC SDR
to the value of the PPE's SPRN_SDR1 once at SPE initialization, so this
change renames mfc_sdr_set() to mfc_sdr_setup() and moves the
access of SPRN_SDR1 into the mmio wrapper. It also removes the now
unneeded member mfc_sdr_RW from struct spu_priv1_collapsed.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
It makes for a friendlier API if irq_dispose_mapping(NO_IRQ) is a
nop, rather than triggering a WARN_ON.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixed some missing files to be deleted when running make clean
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On CHRP platforms with only a 8259 controller, we should set the
default IRQ host to the 8259 driver's one for the IRQ probing
fallbacks to work in case the IRQ tree is incorrect (like on
Pegasos for example). Without this fix, we get a bunch of WARN_ON's
during boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This causes ipic_set_irq_type to set the handler directly rather
than call set_irq_handler, which causes spinlock recursion because
the lock is already held when ipic_set_irq_type is called.
I'm also not convinced that ipic_set_irq_type should be changing the
handler at all. There seem to be several controllers that don't and
several that do. Those that do would break what appears to be a common
usage of calling set_irq_chip_and_handler followed by set_irq_type, if a
non-standard handler were to be used. OTOH, irq_create_of_mapping()
doesn't set the handler, but only calls set_irq_type().
This patch gets things working in the spinlock-debugging-enabled case,
but I'm curious as to where the handler setting is ideally supposed to be
done. I don't see any documentation on set_irq_type() that clarifies
what the semantics are supposed to be.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPC8323EMDS board ethernet interface with RMII uses the CLK16 divisor
for the rx and tx clock, but the ucc_set_qe_mux_rxtx() function doesn't
handle the CLK16 setting of the CMXUCR3 and CMXUCR4 registers. This
fixes it.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, spufs_mbox_read transfers more bytes than requested on a
read. If you ask for four bytes, you get eight. This fixes it to
transfer the largest multiple of four bytes that is less than or equal
to the number you asked for.
Note: one nasty property of this file in spufs is that you can only
read multiples of four bytes in the first place, since there is no way
to atomically put back a few bytes into the hardware register. Thus,
reading less than four bytes returns -EINVAL. Asking for more than
four returns the largest possible multiple of four.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the /signal2 file to actually give signal2 data.
Signed-off-by: Dwayne Grant Mcconnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
