* Add struct ide_io_ports and use it instead of `unsigned long io_ports[]`
in ide_hwif_t.
* Rename io_ports[] in hw_regs_t to io_ports_array[].
* Use un-named union for 'unsigned long io_ports_array[]' and 'struct
ide_io_ports io_ports' in hw_regs_t.
* Remove IDE_*_OFFSET defines.
v2:
* scc_pata.c build fix from Stephen Rothwell.
v3:
* Fix ctl_adrr typo in Sparc-specific part of ns87415.c.
(Noticed by Andrew Morton)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix unbalanced parenthesis.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These patches add full SSP/MCU support for the HP Jornada 720
machine. Its needed to handle keyboard, touchscreen, battery
and backlight/lcd.
The main driver exports functions and the header file exports
the command values. When talking to the MCU the general procedure
is to start MCU, send command (using ssp_inout(command)), the
proper reply is always TXDUMMY. After receiving TXDUMMY you can
send the value you wish pushed (for example brightness level).
End with ssp_end() so the spinlock gets unlocked.
Drivers using this havent been implemented yet, but will shortly.
Signed-off-by: Kristoffer Ericson <Kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the new get_irqnr_preamble macro to move the address of the IRQ
controller outside the IRQ handling loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/241),
this patch
- adds gpio_direction_input/output functions to
generic.c instead of making them inline,
- fixes comment and includes and uses inline functions
instead of macros in gpio.h
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_irqnr_preamble allows machines to take some action before entering the
get_irqnr_and_base loop. On iop we enable cp6 access.
arch_ret_to_user is added to the userspace return path to allow individual
architectures to take actions, like disabling coprocessor access, before
the final return to userspace.
Per Nicolas Pitre's note, there is no need to cp_wait on the return to user
as the latency to return is sufficient.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most architectures have fairly simple discontiguous memory - a
simple set of successive regions each containing some memory.
These can be described simply as a log2 of their maximum size,
along with the base address of the first region and the number
of regions.
The base address is already described by PHYS_PFN_OFFSET, and
the number of regions via the MAX_NUMNODES and the number of
online nodes.
If we then supply the log2 of their maximum size, all the other
discontigmem macros can move into generic code.
There is one exception: lh7a40x seems to have a more complicated
setup; this is left alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* We don't need this header anymore - there is no data we need to share this way. FB driver gets this data through a resources structure. MCU Driver api will go to a jornada720_mcu.h file.
Signed-off-by: Filip Zyzniewski <filip.zyzniewski@tefnet.pl>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds relevant MCU commands for the j7xx chipset.
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patch from Andrew Victor
Remove the remaining legacy __mem_isa() definitions for the ARM
platforms.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FLUSH_BASE must be visible to arch/arm/mm/init.c in order for the
memory region to be setup. Move these definitions from
asm-arm/arch-*/hardware.h into asm-arm/arch-*/memory.h where mm
stuff can see them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per the corresponding change to the serial drivers, arrange
for ARM decompressors to give CRLF. Move the common putstr code
into misc.c such that machines only need to supply "putc" and
"flush" functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the HZ definition into Kconfig, and set appropriate defaults
for platforms. Remove mostly empty asm/arch/param.h include file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we now only build arch/arm/kernel/dma.c on machine types
which set ISA_DMA_API, we don't need to define MAX_DMA_CHANNELS
to 0 to indicate this - this definition becomes superfluous.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, we have a symbol clash between the SA-1100 header and
some drivers. Since everywhere which needs SA1100 specifics includes
asm/hardware.h, we don't need to include it in the SA1100 io.h header.
In file included from drivers/net/wireless/wavelan_cs.p.h:459,
from drivers/net/wireless/wavelan_cs.c:60:
drivers/net/wireless/wavelan_cs.h:97:1: warning: "LCSR" redefined
In file included from include/asm/arch/hardware.h:56,
from include/asm/hardware.h:16,
from include/asm/arch/io.h:13,
from include/asm/io.h:71,
from drivers/net/wireless/wavelan_cs.p.h:433,
from drivers/net/wireless/wavelan_cs.c:60:
include/asm/arch/SA-1100.h:1907:1: warning: this is the location of the previous definition
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, using PAGE_SHIFT in asm/arch/memory.h is unsafe, and we
can't include asm/page.h into this file because then we have a circular
dependency. Move the offending code to arch/arm/common/sa1111.c
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch allows for assorted type of cleanups by letting assembly code
use the same set of defines for constant values and avoid duplicated
definitions that might not always be in sync, or that might simply be
confusing due to the different names for the same thing.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Including asm/hardware.h into asm/io.h can cause #define clashes
between platform specific definitions and driver local definitions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform device data for the SA11x0 MCP device. This allows
platforms to customise the configuration of the SA11x0 MCP device
according to their needs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VMALLOC_START and VMALLOC_OFFSET are common between all ARM
machine classes. Move them into include/asm-arm/pgtable.h,
but allow a machine class to override them if required.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
