Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than checking for some known failures, check positively for the
success response code 0x0001 and return -EIO for unrecognized failure
response codes.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg Smith <gsmith@nc.rr.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Windfarm PID module lacks a licence, it should be GPL, here it is
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fix some compatiblity issues with big endian systems
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the same ttyIx device was opened by two processes the module was not
released and so the usage count went never to zero again. This oneliner fixes
the issue.
Signed-off-by: Oskar Senft <o.senft@sirrix.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new PCI IDs for HFC-S PCI based ISDN TA 'Primux II S0' and 'Primux II S0'
from Gerdes AG
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SCSI layer uses SCSI_SENSE_BUFFERSIZE (96) for the sense buffer
size, even though some other code uses "sizeof(struct request_sense)"
(which is 64 bytes). Allocate the buffer using the bigger of the two
for safety.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a use-after-free bug in the usb-serial core. It is simple to
trigger this (open a usb-serial port, then yank the device out before
closing the port.) Thanks to Stefan Seyfried <seife@suse.de> for
reporting this, and to the slab debugging code which enabled it to be
tracked down.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
memset() is called before check.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a trivial compilation warning:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_dma_callback’:
drivers/mmc/au1xmmc.c:743: warning: unused variable ‘status’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c doesn't compile because commit
e92251762d introduced a typo and passes
the wrong argument to the mmc_resp_type macro.
Error because of the typo:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: warning: implicit declaration of function ‘mmc_rsp_type’
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `au1xmmc_request':au1xmmc.c:(.text+0x89504): undefined reference to `mmc_rsp_type'
:au1xmmc.c:(.text+0x8968c): undefined reference to `mmc_rsp_type'
make: *** [.tmp_vmlinux1] Error 1
Error because of the wrong argument:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: error: invalid type argument of ‘->’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c currently doesn't compile; it needs to be
converted to use platform_driver. I cannot test this change because
of lack of hardware but I followed the drivers this one is based on,
and the code is certainly not worse than before.
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:1002: error: ‘platform_bus_type’ undeclared here (not in a function)
make[2]: *** [drivers/mmc/au1xmmc.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mac_addr variable doesn't get reset between
(re)additions of multicast addresses. One byte
of all multicast addresses (except the first)
can be incorrect.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Almost all the code for the VIA RNG is guarded with __i386__ #ifdefs,
the only exception being the enumeration of RNG types which is used to
index into the rng_vector ops array. This patch adds an ifdef around
that for consistency and since the guard makes a difference when adding
new RNG types on non-i386 hardware.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-Off-By: Jeff Garzik <jeff@garzik.org>
Sync up the recent redboot fix with MTD CVS. It uses the correct swab()
functions.
Cc: John Bowler <jbowler@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using this patch, Omnikey CardMan 4000 and 4040 devices automatically
get their device nodes created by udev.
Also, we now check for (and handle) failure of pcmcia_register_driver()
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The axnet_cs driver can support the AMB8110 PC Card, so add the id for it.
In the old pcmcia-cs config file, this card is listed with the comment "not
specific enough". The last entry in the axnet_ids has the same comment.
They are disabled, and for good reason as it was originally identified by
the MANFID, and that is shared with several cards that use both the
pcnet_cs driver and axnet_cs driver. I tried my AMB8110 with pcnet_cs, and
found that it works fine, and I cannot find a reason for either, except
that the old config file recommended axnet_cs.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't just use cards with PCMCIA ID 0x0156, 0x0002. Make sure that the
vendor string is "Intersil" or "INTERSIL"
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The second pseudo multi-function device of a PCMCIA card may only be
configured once the first one is initialized. Therefore, delay the
registration of the second device until the first one is initialized.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net
Comment out debug code in tty receive buffering. For performance reasons
(I'll keep it enabled in -mm).
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is Adam's pnp probing fix. It's been reported to fix hangs on several
people's machines. I don't know if it's official or final, and Adam isn't
contactable at present. But I'm not aware of the patch causing any
regressions.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some "inline" removing that Andrew suggested, removed some locking on
add/remove at this level - we'll let the callees decide.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The RedBoot boot loader writes flash partition tables containing native
byte sex 32 bit values. When booting an opposite byte sex kernel (e.g. an
LE kernel from BE RedBoot) the current MTD driver fails to handle the
partition table and therefore is unable to generate the correct partition
map for the flash.
So far as I am aware this problem is ARM specific, because only ARM
supports software change of the CPU (memory system) byte sex, however the
partition table parsing is in generic MTD code. The patch below has been
tested on NSLU2 (an IXP4XX based system) with a patch,
10-ixp4xx-copy-from.patch (submitted to linux-arm-kernel - it's ARM
specific) required to make the maps/ixp4xx.c driver work with an LE kernel.
Builds of the patched system are in the 'unstable' release of OpenSlug and
UcSlugC available from www.nslu2-linux.org. These builds are BE, the
archives at www.nslu2-linux.org and www.handhelds.org (see
monotone.vanille.de) can be built LE (currently DISTRO targets
nslu-ltu.conf for LE thumb uclibc (32 bit kernel) and nslu2-lau.conf,
nslu2-lag.conf for LE arm uclibc/glibc) and this patch has been tested
extensively will both BE and LE systems on the NSLU2 (including swapping
between BE and LE by reflashing from both RedBoot and Linux).
The patch recognises that the FIS directory (the partition table) is
byte-reversed by examining the partition table size, which is known to be
one erase block (this is an assumption made elsewhere in redboot.c). If
the size matches the erase block after byte swapping the value then
byte-reversal is assumed, if not no further action is taken. The patched
code is fail safe; should redboot.c be changed to support a partition table
with a modified size field the test will fail and the partition table will
be assumed to have the host byte sex.
If byte-reversal is detected the patch byte swaps the remainder of the 32
bit fields in the copy of the table; this copy is then used to set up the
MTD partition map.
Signed-off-by: John Bowler <jbowler@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch attempted to enable more efficient memory usage by using
only 2kB descriptors for jumbo frames. The method used to implement this
has since been commented upon as "illegal" and in recent kernels even
causes a BUG when receiving ip fragments while using jumbo frames.
This patch simply goes back to the way things were. We expect some
complaints due to order 3 allocations failing to come back due to this
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.
In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds a bunch of new device IDs to the ftdi_sio driver for
various devices from microHAM using FTDI chips.
Micheal Studer supplied the PID for the USB-Y9 device. I examined the
INF file in microHAM's Windows driver package for the USB-KW, USB-YS,
USB-IC, USB-DB9 and USB-RS232 devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the USB vendorID of GSPDA and the productID of GSPDA's palm
smartphone 'xplore m68' to the list of known devices.
Signed-off-by: Hendrik Schweppe <linuxkpatch@hendrik.fam-schweppe.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote NDIS response to OID_GEN_SUPPORTED_LIST only allocated space
for the data attached to the reply, and not the reply structure
itself. This caused other kmalloc'd memory to be corrupted.
Signed-off-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a dead lock in lh7a40x udc driver. When the driver receive a
SET_FEATURE HALT request, the dev lock is taken by the interrupt
handler lh7a40x_udc_irq then the handler will call lh7a40x_set_halt
function which in its turn will try to acquire the dev lock.
Signed-off-by: Franck Bui-Huu <franck.bui-huu@innova-card.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as656) adds an unusual_devs.h entry for the Lyra RCA RD1080
MP3 player. Its card-reader firmware has the common
report-one-too-many-sectors bug. This fixes Novell bug #152175.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for the Dual USB Joypad [0925:8866] from Wisegroup. The
HID_QUIRK_NOGET is necessary for it to respond to input, and the
HID_QUIRK_MULTI_INPUT is necessary to have two js# nodes appear.
Signed-off-by: Andrew Fuller <mactalla.obair@gmail.com>
Cc: "Dmitry Torokhov" <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=6128
Finish morphing the "early handoff" version of the EHCI BIOS handshake over
to match the previous implementation inside the EHCI driver (except that
now we forcibly disable the SMI). The version that had been with the PCI
code was surprisingly full of bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <yazar256@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
