Set up METHOD_GPIO_44XX instead of trying to use the METHOD_GPIO_24XX.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only usage of _toggle_gpio_edge_triggering is in
an #ifdef CONFIG_ARCH_OMAP1 block, so only provide it if
CONFIG_ARCH_OMAP1 is defined, too.
This fixes a compiler warning:
arch/arm/plat-omap/gpio.c:758: warning: '_toggle_gpio_edge_triggering' defined but not used
when compiling for ARCH_OMAP2, ARCH_OMAP3 or ARCH_OMAP4.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.
Additionally, current code forces rising edge detection if both
flags are specified:
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags. The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis. The mask is only set for those
GPIOs where a toggle is necessary. Edge detection starts out the
same as above with FALLING mode first.
The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt
0x1 1 -> 0 (falling) No interrupt
(set ICR to 0x0 manually)
0x0 0 -> 1 (rising) No interrupt
0x0 1 -> 0 (falling) Interrupt
That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught. If we add in the toggle, we get this:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0)
0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1)
0x1 0 -> 1 ...
so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch disables a GPIO module when all pins of a GPIO
module are inactive (clock gating forced at module level) and
enables the module when any gpio in the module is requested.
The module is enabled only when "mod_usage" indicates that no GPIO
in that module is currently active and the GPIO being requested
is the 1st one to be active in that module.
Each module would be disabled in omap_gpio_free() API when all
GPIOs in a particular module becomes inactive. The module is
re-enabled in omap_gpio_request() API when a GPIO is requested
from the module that was previously disabled.
Since individual GPIO's bookkeeping is added in this patch
via "mod_usage", the same is used in omap_set_gpio_debounce()
& omap_set_gpio_debounce_time() APIs to ensure that the gpio being
used is actually "requested" prior to being used (Nishant Menon's
<nm@ti.comSuggestion)
GPIO module level details are specific to hardware and hence
introducing this patch in low level layer (plat-omap/gpio.c)
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The closing parenthesis was not in the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add context save and restore to enable off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is part of a series which removes references to omap730 in code
which is shared with omap850, replacing them with references to omap7xx.
This updates all the remaining omap730 references in miscellaneous local
variables, macros and similar.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which removes references to omap730 in code
which is shared with omap850, replacing them with references to omap7xx.
Turns INT_730_* to INT_7XX_* for definitions in irqs.h and all users.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (23 commits)
at_hdmac: Rework suspend_late()/resume_early()
PM: Reset transition_started at dpm_resume_noirq
PM: Update kerneldoc comments in drivers/base/power/main.c
PM: Add convenience macro to make switching to dev_pm_ops less error-prone
hp-wmi: Switch driver to dev_pm_ops
floppy: Switch driver to dev_pm_ops
PM: Trivial fixes
PM / Hibernate / Memory hotplug: Always use for_each_populated_zone()
PM/Hibernate: Do not try to allocate too much memory too hard (rev. 2)
PM/Hibernate: Do not release preallocated memory unnecessarily (rev. 2)
PM/Hibernate: Rework shrinking of memory
PM: Fix typo in label name s/Platofrm_finish/Platform_finish/
PM: Run-time PM platform device bus support
PM: Introduce core framework for run-time PM of I/O devices (rev. 17)
Driver Core: Make PM operations a const pointer
PM: Remove platform device suspend_late()/resume_early() V2
USB: Rework musb suspend()/resume_early()
I2C: Rework i2c-s3c2410 suspend_late()/resume() V2
I2C: Rework i2c-pxa suspend_late()/resume_early()
DMA: Rework txx9dmac suspend_late()/resume_early()
...
Fix trivial conflict in drivers/base/platform.c (due to same
constification patch being merged in both sides, along with some other
PM work in the PM branch)
It is possible for GPIO IRQ lines configured with
falling edge triggering only to get IRQs at the
rising edge upon the exit of offmode. And vice
versa. Prevent such IRQs to arrive by generating
the IRQ obeying the detection scheme.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If IRQ triggering is enabled, it can trigger a pending interrupt
even for masked interrupts. Any pending GPIO interrupts can
prevent the powerdomain from hitting retention.
Problem found, reported and additional review and testing by Chunquiu
Wang.
Tested-by: Chunquiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
gpio_get() should return DATAIN register value when the GPIO
is configured as input whereas it should return DATAOUT register
value when the GPIO is configured as output.
Now /sys/kernel/debug/gpio shows proper values for output GPIOs
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch reworks platform driver power management code
for omap drivers using late/early legacy callbacks.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some bootloader may initialize debounce register and this will make
dbclk not consist with the debounce register after linux kernel boot
up.
Signed-off-by: janboe <janboe.ye@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per 3430 TRM, there are 6 banks [0 to 191]
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flush posted write to IRQSTATUS register in GPIO IRQ handler.
This eliminates the below error for all peripherals that use GPIO interrupts.
<4>Spurious irq 95: 0xffffffdf, please flush posted write for irq 31
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO IRQ enable/disable path attempts to also enable IRQ wake
support for the parent GPIO bank IRQ as well. However, since there is
no 'set_wake' hook for the bank IRQs, these calls will always fail.
Also, since the enable will fail on the suspend path, the disable on
the resume path will trigger unbalanced enable/disable warnings.
This was discovered in the suspend/resume path on OMAP3/Beagle using
the gpio-keys driver which disables/re-enables GPIO IRQ wakeups in the
suspend/resume path.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are no wakeup registers on 15xx, and suspend_wakeup
does not exist in the struct gpio_bank.
Without this fix we'll get "arch/arm/plat-omap/gpio.c:1792:
error: 'struct gpio_bank' has no member named 'suspend_wakeup'"
as noted by Russell King.
Note that the ifdefs will be cleaned up once the omap gpio
code gets split into omap1 and omap2 specific parts.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Minor GPIO fixes:
- If get_gpio_bank() fails, then BUG() out.
- In omap_set_gpio_debounce():
* protect the read/modify/write with the relevant spinlock
* make the omap3 clock ops pass "sparse" checking
Except for the spinlock problem, these were reported through "make".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clean up OMAP GPIO request/free functions
- Rename and declare static OMAP specific GPIO request/free functions
- Register them into gpiolib as chip-specific hooks
- Add omap_request_gpio/omap_free_gpio wrappers for existing code not
converted yet to use gpiolib
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
[ dbrownell@users.sourceforge.net: remove needless check_gpio() calls ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are already various drivers having bigger label than 10 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.
Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.
This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the correct wake-up enable register, and make it
work with 34xx also.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
