Using init_hook to call alc888_coef_init() is problematic for configurations
that already set another init_hook. Better to put it in alc_init() as is
(although it looks a bit hackish).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable the snoop for nvidia hda controller to avoid data coherence issue.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some Realtek codecs like ALC882 or ALC883, the capture source is
no mux but sum widget. We have to initialize all channels properly
for this type, otherwise noises may come in from the unused route.
The patch assures to mute unused routes, and unmute the currently
selected route.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, even if you pass model=intel-mac-v3 as a module parameter to
snd_hda_intel, the function patch_stac922x (patch_sigmatel.c) will still
try to auto-detect the model type. This is a problem on my MacBook Pro 1st
generation, which needs intel-mac-v3, but sometimes incorrectly reports
0x00000100 as subsystem id, which causes the switch in patch_stac922x to
select intel-mac-v4.
To fix this, I added a new model called intel-mac-auto, so in case no
module parameter is passed, and an Intel Mac board is detected, the
model will be automatically detected, while no detection will be done
if the model is forced to intel-mac-v3.
This problem has been around for quite a while, and I used to fix it
by moving the case statement for 0x00000100 in patch_stac922x so that
intel-mac-v3 is chosen.
Another way to fix the problem would be to check if a module parameter
was set directly in patch_stac922x, using something like this:
if (spec->board_config == STAC_INTEL_MAC_V3 &&
!codec->bus->modelname) {
But I think it is less elegant (if you prefer that way, I can prepare a
patch).
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the Acer Aspire 5920G (1025:0121) select ALC883_ACER_ASPIRE
by default.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch makes the needlessly global snd_ac97_add_vmaster() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZF_FREQUENCIES and AZF_GAME_CONFIGS were variables, and this doesn't
seem to have been intended.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
communicate the ES137x PCI device to the AC97 code for its
subsys_vendor/device values
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems NVidia and other hardwares require the alignment for period
update timing. For satisfying this condition, align the position
adjustment for delayed wake-up to the initial bdl_pos_adj value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kcalloc is supposed to be called with the count as its first argument and the
element size as the second.
Both arguments are size_t so does not affect correctness. This callsite is
during module_init and therefore not performance critical. Another patch will
optimize the case when the count is variable but the size is fixed.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the missing initialization for unsolicited events on
Cx5045 micsense model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added volume controls for the analog PC Beep on 92hd71bxx codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix a const pointer usage warning in the Digigram miXart soundcard driver. A
const pointer is being passed to copy_from_user() to load the firmware into.
This is okay in this case because the function has allocated the firmware
struct itself, but the const qualifier is part of the firmware struct - so the
patch casts the const away.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix a const pointer usage warning in the Digigram pcxhr compatible soundcard
driver. A const pointer is being passed to copy_from_user() to load the
firmware into. This is okay in this case because the function has allocated
the firmware struct itself, but the const qualifier is part of the firmware
struct - so the patch casts the const away.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Standardise both in-kernel and loaded firmware to be stored as
little-endian instead of host-endian.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The maestro3 driver is byte-swapping its firmware to be host-endian in
advance, when it doesn't seem to be necessary -- we could just use
le16_to_cpu() as we load it.
Doing that means that we need to switch the in-tree firmware to be
little-endian too.
Take the least intrusive way of doing this, which is to switch the
existing snd_m3_convert_from_le() function to convert _to_ little-endian
instead, and use it on the in-tree firmware instead of the loaded
firmware. It's a bit suboptimal but doesn't matter much right now
because we're about to remove the special cases for the in-tree version
anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As reported and tested by an RedHat customer, HP dc7600 with pci sub IDs
0x103c/0x3011 works with the hp-3013 model and not with the hp only model.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
An gpio_mask value was defined twice needlessly.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the model entry (model=lenovo) for Lenovo N3000 N200 laptop
with ALC861-VD. Reference below:
https://bugzilla.novell.com/show_bug.cgi?id=406425
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Replace 'snd_ac97_write' with snd_ac97_write_cache' in pacth_ucb1400 to allow
proper codec wakeup.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Toshiba Satellite P105 with cx5045 has no HP pin but only a
speaker pin and does the speaker-muting on hardware.
Thus the matching model is laptop-micsense.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing SSID of Thinkpad Z60m for model=thinkpad with
AD1981HD.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ALC883 medion model doesn't unmute the proper amps so no output can be heard.
Replaced the mute switches to behave just like other models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some laptops don't like PR3 powerdown. Do PR3 powerdown only
for the real power-saving.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some machines with Cx5045 seem to have no problem with the volume
over 0dB on NID 0x17. Disable amp overrides for other devices but HP.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
YDSXGR_BUF441OUTVOL register isn't initialized properly. This may lead to
a silent output at full volume of unchanged "Wave Playback Volume".
http://bugzilla.kernel.org/show_bug.cgi?id=10963
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
MacBook 3.1 is compatible with model=mbp3.
Added the codec SSID 10b6:3600.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
- fix problem with codec register 0x6a being write-only
by adding a software shadow register
(caused annoying noise after module loading due to _toggling_
between gameport and audio bits instead of configuring them properly)
- rename several "Wave" mixer controls to "PCM", since this is
what Wine and several other apps are looking for (IOW, _requiring_)
and this is what AC97 specs use as naming, too,
thus I'd guess it's what these controls are
- cleanup, small optimizations
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Stop the S/PDIF DMA engine and output when the device is told to pause.
It will keep on looping the current buffer contents if this isn't done.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add the SSID for the "Fujitsu Siemens Amilo M1451G" laptop to
patch_realtek.c , so that it uses ALC880_FUJITSU by default.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the SSID of a known iMac 24" to automatically use
ALC885_IMAC24 quirk.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The irq handler may be called before the proper initialization of hardware.
Call snd_aw2_saa7146_setup() before the irq handler registration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC_VERB_GET_DIGI_CONVERT_2 isn't actually implemented but reserved.
The whole SIC bits are returned from DIGI_CONVERT_1.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
