* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Add support for 1533 bridge to alim1535_wdt
[WATCHDOG] Add a 00-INDEX file to Documentation/watchdog/
[WATCHDOG] Eurotechwdt.c - clean-up comments
Update get_dvb_firmware script for the new location of the
tda10046 firmware.
The old location doesn't work anymore.
Signed-off-by: Andreas Arens <ari@goron.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
thermal.act=-1 disables all active trip points
in all ACPI thermal zones.
thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature. However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one). Lowering this trip point may
kick in the fan sooner.
Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.
WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points. They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.
There are two cases where this option is used:
1. Debugging a hot system crossing valid trip point.
If your system fan is spinning at full speed,
be sure that the vent is not clogged with dust.
Many laptops have very fine thermal fins that are easily blocked.
Check that the processor fan-sink is properly seated,
has the proper thermal grease, and is really spinning.
Check for fan related options in BIOS SETUP.
Sometimes there is a performance vs quiet option.
Defaults are generally the most conservative.
If your fan is not spinning, yet /proc/acpi/fan/
has files in it, please file a Linux/ACPI bug.
WARNING: you risk shortening the lifetime of your
hardware if you use this parameter on a hot system.
Note that this refers to all system components,
including the disk drive.
2. Working around a cool system crossing critical
trip point due to erroneous temperature reading.
Try again with CONFIG_HWMON=n
There is known potential for conflict between the
the hwmon sub-system and the ACPI BIOS.
If this fixes it, notify lm-sensors@lm-sensors.org
and linux-acpi@vger.kernel.org
Otherwise, file a Linux/ACPI bug, or notify
just linux-acpi@vger.kernel.org.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.
"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.
thermal.psv is checked at module load time,
and in response to trip-point change events.
Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed. To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.
Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.
WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: Len Brown <len.brown@intel.com>
Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.
If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.
(note _TZP and thermal.tzp units are in deci-seconds,
so _TZP = 300 corresponds to 30 seconds)
If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".
However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones
Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)
There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.
The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.
But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events. Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.
But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.
Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.off=1" disables all ACPI thermal support at boot time.
CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.
WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: Len Brown <len.brown@intel.com>
The documentation used "thinkpad-acpi" to refer to the directories in
sysfs, while it should have been using "thinkpad_acpi". Thanks to Hugh
Dickins for the error report.
I wish I could just call the module and everything else by the proper
name with the "-", instead of using these ugly translations to "_".
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some people writing boot loaders seem to falsely belief the 32bit zero page is a
stable interface for out of tree code like the real mode boot protocol. Add a comment
clarifying that is not true.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A warning note from Sam Ravnborg about kconfig's select evilness,
dependencies and the future (slightly corrected).
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In Documentation/sysrq.txt, the description of 'h' says that any key not
listed *above* will generate help. That's obviously not true since all the
keys listed below 'h' will do what they are described to do, not display help.
So change the text so that it says that any key not listed in the table will
generate help, which is what really happens.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/watchdog/watchdog.txt does not exist, it is Documentation/watchdog/wdt.txt
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is add a document for memory hotplug to describe "How to use" and
"Current status".
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current version is very old and does not correctly specify how to
set the video mode.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a little problem in Documentation/vm/slabinfo.c
The code is using "%d" in a printf() call to print an 'unsigned long'.
This patch corrects it to use "%lu" instead.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
UIO currently contains a rather dubious statement which wants removing.
The actual questions around whether user space code that depends tightly
on kernel GPL code designed to co-work with it are derivative works of
the kernel is extremely complex, and since we don't have space for either
a masters length essay on legal issues or need to start flamewars lets
simply remove the comment and leave law to lawyers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <tovalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: (61 commits)
sched: refine negative nice level granularity
sched: fix update_stats_enqueue() reniced codepath
sched: round a bit better
sched: make the multiplication table more accurate
sched: optimize update_rq_clock() calls in the load-balancer
sched: optimize activate_task()
sched: clean up set_curr_task_fair()
sched: remove __update_rq_clock() call from entity_tick()
sched: move the __update_rq_clock() call to scheduler_tick()
sched debug: remove the 'u64 now' parameter from print_task()/_rq()
sched: remove the 'u64 now' local variables
sched: remove the 'u64 now' parameter from deactivate_task()
sched: remove the 'u64 now' parameter from dequeue_task()
sched: remove the 'u64 now' parameter from enqueue_task()
sched: remove the 'u64 now' parameter from dec_nr_running()
sched: remove the 'u64 now' parameter from inc_nr_running()
sched: remove the 'u64 now' parameter from dec_load()
sched: remove the 'u64 now' parameter from inc_load()
sched: remove the 'u64 now' parameter from update_curr_load()
sched: remove the 'u64 now' parameter from ->task_new()
...
Some versions of ld.so mmap the shared libraries right in over guest
memory, so compile lguest statically by default.
[ FC7 maps shared libraries very low, where the launcher maps guest's
physical memory. Quick fix is to link Launcher static, real fix is
for 2.6.24. ]
-static is a simple fix. I expect this problem will be more common than we
like, as different distro's make different "improvements" to ld.so
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grub older than 0.93 are broken when the kernel setup is bigger than
8K. This was fixed in 2002, and 0.93 was the first grub version which
fixed this bug.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: fscher read control bugfix
hwmon: (adm1031) Fix broken links in documentation
hwmon: make abituguru3_read_increment_offset() static
hwmon: Fix regression caused by typo in lm90.c
hwmon: (applesmc) add temperature sensors set for Macbook
hwmon: fscher control update bugfix
hwmon: fix dme1737 temp fault attribute
hwmon: Add missing __devexit tags in various drivers
hwmon: clean up duplicate includes
hwmon: fix lm78 detection regression
hwmon: fix array overruns in lm93.c
hwmon: add support for THMC50 and ADM1022
The specification link in hpet document is broken.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix docbook warnings:
Warning(linux-2.6.22-git12//drivers/base/power/main.c): no structured comments found
Warning(linux-2.6.22-git12//include/linux/splice.h): no structured comments found
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a simple utility used to test SPI functionality. It could stand
growing options to support using other test data patterns; this initial
version only issues full duplex transfers, which rules out 3WIRE or
Microwire links.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7e92b4fc34. It broke Sébastien Dugué's
machine and Jeff said (persuasively)
This seems like it will break decades-long-working stuff, in favor of
breaking new ground in our favorite area, "trusting the BIOS."
It's just not worth it for serial ports, IMO. Serial ports are something
that just shouldn't break at this late stage in the game. My new Intel
platform boxes don't even have serial ports, so I question the value of
messing with serial port probing even more... because... just wait a year,
and your box won't have a serial port either! :)
I certainly don't object to the use of platform devices (or isa_driver),
but the probe change seems questionable. That's sorta analagous to
rewriting the floppy driver probe routine. Sure you could do it... but why
risk all that damage and go through debugging all over again?
It seems clear from this report that we cannot, should not, trust BIOS for
something (a) so simple and (b) that has been working for over a decade.
Much discussion ensued and we've decided to have another go at all of this.
Cc: Sébastien Dugué <sebastien.dugue@bull.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix PNP docbook warnings:
Warning(linux-2623-rc1g4//drivers/pnp/core.c): no structured comments found
Warning(linux-2623-rc1g4//drivers/pnp/driver.c): no structured comments found
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates based on recent .gitignore updates:
*.o.*: Says Alexey Dobriyan:
These are presumably temporary gcc files, which aren't interesting.
setup.bin, setup.elf: new x86 boot code files (from Matthew Wilcox)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Analog Devices chip information pages moved to a different location.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for THMC50 and ADM1022 hardware monitoring chips.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sclp_vt220 error handling.
[S390] cio: Reorganize initialization.
[S390] cio: Make CIO_* macros safe if dbfs are not available.
[S390] cio: Clean up messages.
[S390] Fix IRQ tracing.
[S390] vmur: fix diag14_read.
[S390] Wire up sys_fallocate.
[S390] add types.h include to s390_ext.h
[S390] cio: Remove deprecated rdc/rcd.
[S390] Get rid of new section mismatch warnings.
[S390] sclp: kill unused SCLP config option.
[S390] cio: Remove remains of _ccw_device_get_device_number().
[S390] cio: css_sch_device_register() can be made static.
[S390] Improve __smp_call_function_map.
[S390] Convert to smp_call_function_single.
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
docbook: add pipes, other fixes
blktrace: use cpu_clock() instead of sched_clock()
bsg: Fix build for CONFIG_BLOCK=n
[patch] QUEUE_FLAG_READFULL QUEUE_FLAG_WRITEFULL comment fix
http://marc.info/?l=linux-kernel&m=118481061928246&w=2 seems to
indicate disfavour of "deprecated", so let's just kill it now.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix some typos in pipe.c and splice.c.
Add pipes API to kernel-api.tmpl.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
