It was already fixed more sufficiently by Andrew Morton's
change 843c944fb8.
Noted by Duncan Sands.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Option Card driver:
- remove a deadlock
- add sponsor notice
- add new card
- renamed the device to what's usually printed on it
- removed some dead code
- clean up a bunch of irregular whitespace (end-of-line, tabs)
Also add a MAINTAINERS entry for the Option Card driver.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following driver provides complete interrupt-in and interrupt-out
reports (raw data) to a user program. Until now it uses the
HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it
will be ok for you - and I will be happy, if you assign 8 minor numbers.
I have tested it in several environments and it works very well for me.
However, it has a problem with two or more devices at the same hub, if
the two or more devices need 1 ms interrupt-in transfers. Unfortunately
more than one interrupt-in transfer every ms isn't possible (ehci
driver?). This is why the min_interrupt_in_interval and
min_interrupt_out_interval are increased to 2 ms (see the corresponding
module parameters). This way, I can use two devices simultaneously at
the same hub.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This increases the reference count on the usb cdc acm control interface
which is referred to by the tty interface provided by the driver. This
allows the deferred removal of the tty after the physical device is
disconnected if the tty is held open at the time of disconnection.
Signed-off-by: brian@murphy.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export usb_get_intf and usb_put_intf so that modules can increase
usb interface reference counts.
Signed-off-by: brian@murphy.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A patch re-organizing some parts of root hub initialization deleted the
code initializing the bus-neutral reboot/shutdown notifier for OHCI.
This patch just restores that deleted code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent "pm_message_t" changes removed functionality from the Linux
PM framework. This patch removes it from the OMAP OHCI too, removing
the distinction between (previous) PM_SUSPEND_MEM and PM_SUSPEND_DISK
state transitions ... now the only suspend semantics supportable are
what was previously PM_SUSPEND_DISK (4) and is now "PMSG_SUSPEND" (3).
From: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor OMAP updates that somehow got dropped from previous patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I also needed the following on 2.6.13-rc1 without CONFIG_USB_ETH_RNDIS,
symbol fs_status_desc isn't available in that case on PXA255.
This builds both with and without ETH_RNDIS, but I haven't actually
tested either.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
below you will find one patch to hid-core.c, which lets usbhid ignore
our HID devices. It would be nice, if you can apply it.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The length of the array desc->bitmap is 3, and not 4:
Definitions involved:
In drivers/usb/core/hcd.h
464 #define bitmap DeviceRemovable
In drivers/usb/host/ohci-hub.c
395 struct usb_hub_descriptor *desc
In drivers/usb/core/hub.h
130 struct usb_hub_descriptor {
131 __u8 bDescLength;
132 __u8 bDescriptorType;
133 __u8 bNbrPorts;
134 __u16 wHubCharacteristics;
135 __u8 bPwrOn2PwrGood;
136 __u8 bHubContrCurrent;
137 /* add 1 bit for hub status change; round to bytes */
138 __u8 DeviceRemovable[(USB_MAXCHILDREN + 1 + 7) / 8];
139 __u8 PortPwrCtrlMask[(USB_MAXCHILDREN + 1 + 7) / 8];
140 } __attribute__ ((packed));
In include/linux/usb.h
306 #define USB_MAXCHILDREN (16)
This defect was found automatically by Coverity Prevent, a static analysis
tool.
(akpm: this code should be shot. Field `bitmap' doesn't exist in struct
usb_hub_descriptor. And this .c file is #included in
drivers/usb/host/ohci-hcd.c, and someone somewhere #defines `bitmap' to
`DeviceRemovable'.
>From a maintainability POV it would be better to memset the whole array
beforehand - I changed the patch to do that)
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Cc: <linux-usb-devel@lists.sourceforge.net?
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a basic keypress input driver for the Keyspan Digital
Remote with part number UIA-11. Currently there is an older remote with
part number UIA-10 which isn't supported by this driver. Support for
the older UIA-10 could be added but a binary file is required to be
download to the device, and I don't have that file. I also don't have a
UIA-10 device so I wouldn't be able to test any of the changes.
Signed-off-by: Michael Downey <downey@zymeta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/net2280.c: In function 'show_registers':
drivers/usb/gadget/net2280.c:1501: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg,
This patch fixes the kmalloc() flags argument type in USB
subsystem; hopefully all of its occurences. The patch was
made against patch-2.6.12-git2 from Jun 20.
Cleanup of flags for kmalloc() in USB subsystem.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sorry that it took so long. Here comes a cleanup patch that
addresses the remarks by Alexey Dobriyan about
gregkh-usb-usb-isp116x-hcd-add.patch EXCEPT the remark about
the typecasting of mem_flags argument for kcalloc; this will
be addressed in a later patch.
OlavCleanup of isp116x-hcd.
Signed off by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make usbmon to print Setup packets of Control transfers. This is useful
when debugging enumeration issues.
This is a change to the trace format which is not fully compatible.
A parser has to look at the data length word now. If that word is
a character like 's', read setup packet before proceeding with data.
I decided not to bump the API tag for this because not many such
parsers exist at this point.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
although 2.6.12 now contains the sisusb driver, it failes to build this
driver due to a missing patch of the Makefile.
From: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We map states 0x00 and 0x10 to the ATM_PHY_SIG_LOST flag. The current logic fails to
resync the line if we get state 0x10 followed by 0x00, since we only resync the line
when the state is 0x00 and the flag changed. Doubly fixed by (1) always resyncing the
line when the state is 0x00 even if the state didn't change, and (2) keeping track of
the last state, not just the flag. We do (2) as well as (1) in order to get better log
messages.
This is a tweaked version of the original patch by Aurelio Arroyo.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No functional change, but less likely to break in the future.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Remove redundant handling of TIOCMBIS and TIOCMBIC ioctls
as they are handled in the tty layer and never reach this driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Use a single usb_device_id table and detect the type of chip
programatically. The table also flags devices requiring special
initialization. The patch makes the driver about 10K smaller and makes
it easier to add new device IDs.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes an unneeded subclass and protocol from the
07af/0005/100 entry in unsual_devs.h as reported by Alfred Ganz
<alfred-ganz@agci.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Catch up with some PCMCIA API changes:
- Docs say that as of 2.6.11 the PCMCIA IRQInfo2 field is ignored,
but it's not yet removed from the API; stop using it anyway.
- As of 2.6.13 PCMCIA finally hotplugs and does driver binding
without "cardmgr"; add a MODULE_DEVICE_TABLE to support this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes CONFIG_PMAC_PBOOK (PowerBook support). This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one-liner fixes a test for interfaces that are already resumed.
It would be nice if this could get into 2.6.12, but it's not critical
since it only affects people doing selective (runtime) suspend/resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a build error on pxa25x processes with pxa2xx_udc and
CONFIG_USB_ETH=m
# CONFIG_USB_ETH_RNDIS is not set
The error is because on that CPU there's no status transfer support
except with RNDIS. Workaround, enable the RNDIS support too.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One debug message won't print the right value; OSDL bugid 4545.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as527, and was rediffed by me.
Since the IDE interface doesn't convey much information about types of
errors, many USB-IDE adapters report all low-level errors with SK = 0x04,
which is supposed to be used only for non-recoverable errors. As a result
the SCSI midlayer doesn't retry the command. But quite often a retry
would succeed, whereas an unnecessary retry doesn't really hurt anything.
This patch uses a recently-implemented flag to tell the SCSI midlayer that
such hardware errors should be retried.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch causes a port reset whenever there's a transport error or abort.
If that fails it reverts back to doing a mass-storage device reset. It
started life as as497 and was rediffed by me.
This makes error recovery a lot quicker and more reliable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does two things to help reset recovery. It started life as
as496 and was rediffed by me.
First, the patch checks the result of a CLEAR_HALT request and doesn't reset the
endpoint's data toggle unless the request succeeded.
Second, it reduces the timeout for a device reset from 20 seconds to 5
seconds.
If all goes well, then I've finally figured quilt out and this patch should
apply cleanly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
up(&usblp->sem) was called twice in a row in this code path.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> On Sun, Apr 10, 2005 at 07:21:28PM +0600, Viktor A. Danilov wrote:
> >
> > PROBLEM: aiptek input doesn`t register `device` & `driver` section in sysfs (/sys/class/input/event#)
> > REASON: `dev` - field not filled...
> > SOLUTION: in linux/drivers/usb/input/aiptek.c write
> > aiptek->inputdev.dev = &intf->dev;
> > before calling
> > input_register_device(&aiptek->inputdev);
The following (tested) patch fixes the exact same issue with the ATI
Remote input driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for Creative WebCam Go Mini.
Camera has STV680 chip and just different Product ID(0x4007) and Vendor ID (0x041e).
Signed-off-by: Kiril Jovchev <jovchev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialize status fields in the read and write urbs to prevent a race
condition with open/read/close - open/write/close sequences.
Fixes bug #4432 at bugzilla.kernel.org
Signed-off-by: Adam Oldham <oldhamca@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The itd_patch() function is responsible for allocating entries in the
buffer page pointer list of the iTD. Particularly, a new page pointer
is needed every time when buffer data crosses a page boundary.
However, there is a bug in the allocation logic: the function does not
allocate a new entry when the current transaction is the first
transaction in the iTD (as indicated by first!=0).
The consequence is that, when the data of the first transaction begins
somewhere at the end of a page so that it actually does cross the page
boundary, no new page pointer is allocated. This means that the data
at the end of the first transaction (beyond the page boundary) will be
accessed by the HC using the second page pointer, which is zero.
Furthermore, the first page pointer will be later overwritten by the
page pointers of the other transactions, which will garble it because
the value is or-ed into the iTD field.
All this particular check (for !first) does is cause incorrect
behaviour, so it should be entirely removed (and with it the variable
first that is not used for anything else).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
