Add PLD functions for Runtime suspend and resume callbacks,
and enable Runtime PM support for Moselle.
Change-Id: Ie990334c0c60892ec0f0ad6fac3253b3d326a919
CRs-Fixed: 2720832
In the noisy environment observation is, host sends SAE commit req to
AP and gets SAE commit response from AP, then host sends SAE confirm
req to AP but due to noisy environment AP miss the ack for SAE commit
response and keep sending SAE commit response even host send SAE
confirm. As host cleans SAE auth retry frames on reception of SAE auth
rx from AP, host cleanups SAE auth confirm req and disable SAE auth
retry timer. This leads to SAE auth failure. To avoid this host matches
auth frame's "sae algo sequence number" with last sent auth frame's "sae
algo sequence number", if it matches then only free sae auth retry frame
and deactivate sae auth retry timer.
Change-Id: Ia9ae2e5d82c696efdc0aaf4e04b6760b9829c510
CRs-Fixed: 2720436
Add check to verify channel bonding mode before setting 40MHz
capability in HE 2.4GHz.
Change-Id: I22ca48c984cc833835d22d8b7ecfe8a3e194d406
CRs-Fixed: 2723207
Update proper authmode in crypto as for WPA/WPA2/WPA3 also
the auth type from connect request can be OPEN.
So check the wpa_ver and other params from the connect
request to determine proper authmode. Also set authmode and
cipher for WAPI mode.
Change-Id: If1b1cb403afdd42277b9cab2f3c931848f49ab25
CRs-Fixed: 2725312
For SAE auth frames, host configures auth retry timer to 1 second,
if host doesn't get ack for previously sent SAE auth frame then host
retransmit queued SAE auth frame once the periodic auth timer
triggers.
Due to noisy environment host may miss the SAE auth response, in this
case host needs to send queued SAE auth frame. Hence don't reset auth
retry timer on SAE auth TX ack reception.
Change-Id: I96456ce5cbe5fb2acc7005ff1d19c6e9eecc1764
CRs-Fixed: 2725359
Currently once the gEnableSelfRecovery is disabled it is decided to panic
once the firmware complete firmware dump is collected, this has a
side-effect when the normal SSR is triggered for testing purposes.
This reverts commit Ia184a265d0f76e43d1d5edc4bcc0849a05726dac.
Change-Id: Icec14a2afb902a275ffe0bf202ec75d8e58d9f58
CRs-Fixed: 2725430
Add the vendor command attribute to upgrade the QoS
for all UDP packets having priority less than the
current setting.
Change-Id: I1269018396e163c1a2b02a7ab1cfb3fabfd0af94
CRs-Fixed: 2724041
Provide the support to upgrade the priority of
UDP packets based on user setting. The user will
set a particular QoS and for any UDP packets, which
has priority lesser than the current setting, the
QoS will be upgrade to the user set value.
The default value for this setting will be Best Effort.
Change-Id: I64207797e9c000d1d6fb757e22b02ee4f96a36f1
CRs-Fixed: 2724041
If the ACS SCAN failed, the API sap_select_default_oper_chan
will select a default channel from ACS scan channel list.
At present sap_select_default_oper_chan doesn't validate the
channel with regulatory. It may select an invalid channel and
report to hostapd. This will happen when driver is doing ACS
scan, the upper layer set different country code and result to
some channels in the acs freq_list become invalid.
Fix by checking the channel supported by regulatory before select
it.
Change-Id: I438b2947ba1fd5388a2472d5122e55edc89229db
CRs-Fixed: 2723689
For STA in 2.4Ghz band, host adds self HT supported channel width
capability in HT capability field of assoc request.
For WFA certification, expectation is to add self HT supported chan
width capability in HT capability field of assoc request.
Change-Id: I630423de03636e6c4ca07638dce6966c3ca381f9
CRs-Fixed: 2720908
TDLS Sta not initiating Add BA request or responding to Add BA
request from peer. For TDLS connection, legacy rate is
set to zero even though the peer capabilities supports OFDM rates.
The set of available rates from supplicant is compared with config
and rates is populated, which causes the issue.
Fix is to apply the correct rates provided from supplicant
change-ID: I66ce1b0ee4e5f96f9bb755a40ff7d8c46176087c
CRs-Fixed: 2719391
adapter->vdev should never be referenced directly,
Using hdd_objmgr_get_vdev() and hdd_objmgr_put_vdev()
so that proper reference counting is enforced.
Change-Id: I3b9f82631659af8d27377308a14a6f1a83fc3a6d
CRs-Fixed: 2715220
Currently for monitor mode, PS params are disabled during the start
modules and restored at the beginning of stop modules. This will
cause an issue when hdd_wlan_unregister_pm_qos_notifier is called
from stop modules with restored configuration.
To resolve this, restore ps configuration at the end of stop modules.
Change-Id: Ib9db4adf489a8e92cd95cdc547e3c91cc953f1b5
CRs-Fixed: 2720016
In STA+SAP case if AP1 and STA1 have same MAC, and DUT's STA is
connected to AP1. Now when the STA1 tries to connect with DUT's SAP
peer with same mac is already present the add peer fails, but during
delete peer the DUT STA peer (AP1) is deleted instead of STA1 of
DUT's SAP. This leads to SAP deleting peer of a STA interface and
thus the SAP peer count is out of sync.
Fix is to reject any association req from STA1 if AP1 is connected
to DUT's STA. Also ad vdev check while deleting the peer in wma.
Change-Id: I448226497c7aa3c11cb9097be9c7d57eb4239900
CRs-Fixed: 2723814
Currently, driver sends NAN enable/disable request to firmware
and waits for the response. NAN state is cleaned up when NAN
disable indication is received. But if firmware doesn't respond to
NAN enable or disable request, a timeout happens and NAN state is
not cleaned up.
Cleanup the NAN state upon timeout for NAN enable/disable request.
Change-Id: Iadfff2b4d010407f04b529ff81b1ce1f11064695
CRs-Fixed: 2723094
Add PLD_HAS_DRV_SUPPORT to platform capability to indicate if PCIe
DRV is supported or not.
Change-Id: I25dcba18b795988c4cdecd3f0c355de6786e0f3f
CRs-fixed: 2722430
print “tx_complete" values in lim_auth_tx_complete_cnf and
lim_assoc_tx_complete_cnf along with success/fail as well
Change-Id: I0fe60da725df0b90d2e0957877c53bc793826dc6
CRs-Fixed: 2722114
Current flow learning algorithm invalidates the cache for every time
flow is learnt. This results in multiple invalidation when there
multiple flows in quick succession of single NAPI soft IRQ processing.
FW has restriction on number simultaneous message processing.
Delay cache invalidation message so that single message serves multiple
flow learning.
Change-Id: Iee8cb5f12546890f2da32195dc3c4878e7a39ffd
CRs-Fixed: 2718968
Some IOT APs set supported rates to zero in probe response. Host uses
probe response/beacon to update scan cache. Host uses supported rates
from scan cache to update in assoc request.
As the supported rates in probe response are zeros, host doesn't
add supported rate IE in assoc request which leads to association
failure. Hence add BSS basic rates in assoc request if supported
rates in scan cache is not present.
Change-Id: Ie2d75a980f5aede0b7985ddf385516a6b15c7560
CRs-Fixed: 2706797
Recent changes to hdd_regulatory_dyn_cbk broke WWAN n79 and
WIFI 5 GHz co-existence, failure:
1. AGO won't switch channel to 2G even 5G channel disabled.
2. SAP can switch to 2G if 5G disabled, but won't restore back
to 5G when 5G re-enable.
Update callback to call the proper function so that band for
SAP or P2P GO is updated accordingly.
Change-Id: I4087466c9a05250921159d5daff077a8ea7ea495
CRs-fixed: 2718339
For WFA certification testing, host updates station's max nss support
value in the omn ie of association request.
Change-Id: I0b001e0a0953aff0ff8ba614fab3e67c23eb2cfa
CRs-Fixed: 2690460
Update opclass, randomizationInterval and DialogToken in
pilot frame as a response of beacon report request.
Change-Id: Ibf6a6b4d5dea1c87826d7755778c8f559a1a0fa3
Crs-Fixed: 2717259
Currently, after roaming only vht ie is used to get dot11 mode
which may casue issue whenever vendor vht ie is present but vht
ie is not present in beacon. Host updates dot11 mode to
11N based on missing vht ie and does not consider vendor vht but
fw considers vendor vht ie which causes different dot11 modes in
fw and host.
Consider phy mode sent by fw in roam sync event to get dot11
mode to maintain compatibility between host and fw.
Change-Id: Ie9e4cbadd84d239c6f386f296c77677b15ce0500
CRs-Fixed: 2714566
There are different version of SSID structure used in driver, replace
them with struct wlan_ssid.
Change-Id: I8a5bfdafbdc4365afccc11980633272be9c75a81
CRs-Fixed: 2721873
