Hi,
we have run into an issue with blktrace being started for sg devices.
Please apply.
Thanks,
Martin
From: Martin Peschke <mpeschke@linux.vnet.ibm.com>
The device number denoting a generic SCSI devices (sg) in a blktrace
trace is broken; major and minor are always 0. It looks like
sdp->device->sdev_gendev.devt is not initialized properly.
The fix below uses other data to make up a valid device number,
similar to the way an sg device number is generated for sysfs output.
Reported-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were running i/o and performing a bunch of hba resets in a loop.
This forces a lot of target removes and then rescans. Since the
resets are occuring during scan it's causing the scan i/o to timeout,
invoking error recovery, etc. We end up getting some nasty crashing
in scsi_scan.c due to references to old sdevs that are failing
but had some lingering references that kept them around.
Fix by setting device state to SDEV_DEL if the LLD's slave_alloc
fails.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvscsi client driver is not unmapping the SCSI command after
encountering a DMA mapping error while trying to map an indirect
scattergather list for the event pool. This leads to a leak of DMA
entitlement that could result in the device failing future DMA operations
in a CMO environment.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Storage: Update unusual_devs entry for Datafab KECF-USB
USB: Correct Makefile to make isp1760 buildable
USB: option: New mobile broadband modems to be supported
USB: two more usb ids for ti_usb_3410_5052
USB: ftdi_sio: unlock_kernel() on error in set_serial_info()
USB: usb-storage: add Pentax to the bad-vendor list
USB: ftdi_sio: add support for the NDI Polaris system
USB: usb-serial: fix the aircable_init failure path
USB: usb-storage: remove WARN from last-sector hacks
Revert USB: option: add Pantech cards
USB: cdc-acm.c: remove duplicate lines for MTK gps support
USB: fsl_qe_udc: Fix stalled TX requests bug
USB: fsl_qe_udc: Fix muram corruption by disabled endpoints
USB: fsl_qe_udc: Fix disconnects reporting during bus reset
USB: fsl_qe_udc: Fix QE USB controller initialization
USB: fsl_qe_udc: Fix recursive locking bug in ch9getstatus()
USB: fsl_qe_udc: Fix oops on QE UDC probe failure
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: panel: fix lcd panel driver build failure
Staging: android: fix up units in timed_gpio
Staging: android: ram_console: Disable ECC when early init is enabled and validate buffer size
Staging: at76_usb: Add support for OQO Model 01+
Staging: at76_usb: fix bugs introduced by "Staging: at76_usb: cleanup dma on stack issues"
Revert Staging: at76_usb: update drivers/staging/at76_usb w/ mac80211 port
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: Get transition latency from ACPI _PSS table
[CPUFREQ] Make ignore_nice_load setting of ondemand work as expected.
Btrfs was using spin_is_contended to see if it should drop locks before
doing extent allocations during btrfs_search_slot. The idea was to avoid
expensive searches in the tree unless the lock was actually contended.
But, spin_is_contended is specific to the ticket spinlocks on x86, so this
is causing compile errors everywhere else.
In practice, the contention could easily appear some time after we started
doing the extent allocation, and it makes more sense to always drop the lock
instead.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The last build fix I did messed up the units of the sysfs file.
This puts them back to be milliseconds, like they originally were.
Thanks to Juha Motorsportcom for pointing this out.
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Cc: Mike Lockwood <lockwood@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add USB device ID for OQO 01+'s internal wireless LAN
An OQO employee mentions the chip's true identity here:-
ftp://ftp.oqo.com/unsupported/linux/OQOLinux.html
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tracking down the firmware loading problem led to this commit.
$ git bisect bad
0d1d142433 is first bad commit
commit 0d1d142433
Author: Oliver Neukum <oliver@neukum.org>
Date: Thu Dec 18 13:16:40 2008 +0100
Staging: at76_usb: cleanup dma on stack issues
- no DMA on stack
- cleanup unclear endianness issue
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
:040000 040000 c4fee9ea0f8b165a35d1 M drivers
The "no DMA on stack" conversion was incomplete with respect to
updating the arguments passed to usb_control_msg. The value 40 is
hardcoded as it was prior to conversion.
The driver can now load firmware, but is not fully functional.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverts 02227c2839
(Had to be done by hand due to other patches that had come after this.)
Turns out that we don't want the mac80211 port of this driver just yet, as
there is a different driver working on adding this support.
So keep things old and different for now.
This is being reverted at the request of the linux-wireless developers.
Cc: Kalle Valo <kalle.valo@iki.fi>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device suffers from the off-by-one error when reporting the capacity,
so add US_FL_FIX_CAPACITY to the existing entry.
Signed-off-by: Nick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- New Novatel and Dell mobile broadband modem products added
- Dell pid variables used in stead of numerical PIDs for known
products
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds device IDs and balances the counts to make the
hot ID additioning mechanism work.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Cc: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was one error path where unlock_kernel() wasn't called.
This was found with a code checker (http://repo.or.cz/w/smatch.git/)
Compile tested only, sorry.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1202) adds Pentax to usb-storage's list of bad vendors
whose devices always need the CAPACITY_HEURISTICS flag. This is in
addition to the existing entries: Nokia, Nikon, and Motorola.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Virgo Pärna <virgo.parna@mail.ee>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the NDI Polaris system *http://www.ndigital.com/).
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The failure path of aircable_init is wrong, fix the order of (goto) labels.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1201) removes the WARN() from the last-sector hacks in
usb-storage, thereby making the code match the version now in
.27-stable and .28-stable. The WARN() isn't needed, since there is no
longer any intention of assuming that all storage devices have an even
number of sectors, and it annoys users for no good reason.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert 8b6346ec89 as these devices really
work just fine with the cdc-acm driver, as they follow the spec
properly.
Thanks to Chuck Ebbert for pointing out the problem here.
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same patch to add support for MTK gps loggers was submitted by two
different people and applied twice. Remove the redundant lines.
Signed-off-by: James Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While disabling an endpoint the driver nuking any pending requests,
thus completing them with -ESHUTDOWN status. But the driver doesn't
clear the tx_req, which means that a next TX request (after
ep_enable), might get stalled, since the driver won't queue the new
reqests.
This patch fixes a bug I'm observing with ethernet gadget while
playing with ifconfig usb0 up/down (the up/down sequence disables
and enables `in' and `out' endpoints).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before freeing an endpoint's muram memory, we should stop all activity
of the endpoint, otherwise the QE UDC controller might do nasty things
with the muram memory that isn't belong to that endpoint anymore.
The qe_ep_reset() effectively flushes the hardware fifos, finishes all
late transaction and thus prevents the corruption.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Freescale QE UDC controllers can't report the "port change" states,
so the only way to handle disconnects is to process bus reset
interrupts. The bus reset can take some time, that is, few irqs.
Gadgets may print the disconnection events, and this causes few
repetitive messages in the kernel log.
This patch fixes the issue by using the usb_state machine, if the
usb controller has been already reset, just quit the reset irq
early.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.
Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call chain is this:
qe_udc_irq() <- grabs the udc->lock spinlock
rx_irq()
qe_ep0_rx()
ep0_setup_handle()
setup_received_handle()
ch9getstatus()
qe_ep_queue() <- tries to grab the udc->lock again
It seems unsafe to temporarily drop the lock in the ch9getstatus(),
so to fix that bug the lock-less __qe_ep_queue() function
implemented and used by the ch9getstatus().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case of probing errors the driver kfrees the udc_controller, but it
doesn't set the pointer to NULL.
When usb_gadget_register_driver is called, it checks for udc_controller
!= NULL, the check passes and the driver accesses nonexistent memory.
Fix this by setting udc_controller to NULL in case of errors.
While at it, also implement irq_of_parse_and_map()'s failure and cleanup
cases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a client requests a blocking lock, is denied, then requests it again,
then here in nlmsvc_lock() we will call vfs_lock_file() without FL_SLEEP
set, because we've already queued a block and don't need the locks code
to do it again.
But that means vfs_lock_file() will return -EAGAIN instead of
FILE_LOCK_DENIED. So we still need to translate that -EAGAIN return
into a nlm_lck_blocked error in this case, and put ourselves back on
lockd's block list.
The bug was introduced by bde74e4bc6 "locks: add special return
value for asynchronous locks".
Thanks to Frank van Maarseveen for the report; his original test
case was essentially
for i in `seq 30`; do flock /nfsmount/foo sleep 10 & done
Tested-by: Frank van Maarseveen <frankvm@frankvm.com>
Reported-by: Frank van Maarseveen <frankvm@frankvm.com>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The DRI people seem to have a hard time getting these right (see also
commit aeb565dfc3).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: select framebuffer support automatically
drm/i915: add get_vblank_counter function for GM45
drm/i915: capture last_vblank count at IRQ uninstall time too
drm/i915: Unlock mutex on i915_gem_fault() error path
drm/i915: Quiet the message on get/setparam ioctl with an unknown value.
drm/i915: skip LVDS initialization on Apple Mac Mini
drm/i915: sync SDVO code with stable userland modesetting driver
drm/i915: Unref the object after failing to set tiling mode.
drm/i915: add fence register management to execbuf
drm/i915: Return error from i915_gem_object_get_fence_reg() when failing.
drm/i915: Set up an MTRR covering the GTT at driver load.
drm/i915: Skip SDVO/HDMI init when the chipset tells us it's not present.
drm/i915: Suppress GEM teardown on X Server exit in KMS mode.
drm/radeon: fix ioremap conflict with AGP mappings
i915: fix unneeded locking in i915 LVDS get modes code.
Architectures other than mips and x86 are not using ticket spinlocks.
Therefore, the contention on the lock is meaningless, since there is
nobody known to be waiting on it (arguably /fairly/ unfair locks).
Dummy it out to return 0 on other architectures.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's illegal to call flush_dcache_page on slab pages on a number
of architectures. So this patch avoids doing so if PageSlab is
true.
In future we can move the flush_dcache_page call to those page
cache users that actually need it.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 27421e211a, Manually revert
"mlock: downgrade mmap sem while populating mlocked regions", has
introduced its own regression: __mlock_vma_pages_range() may report
an error (for example, -EFAULT from trying to lock down pages from
beyond EOF), but mlock_vma_pages_range() must hide that from its
callers as before.
Reported-by: Sami Farin <safari-kernel@safari.iki.fi>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For historical reason, this driver used its own saving/restoring
of the PCI config space, and used the state of it on resume as
an indication as to whether it needed to re-POST the chip or not.
This methods breaks with the later core changes since the core will
have restored things for us.
This patch fixes it by removing that custom code, using standard
core methods to save/restore state, and testing for the need to
re-POST by comparing the content of a few key PLL registers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes aty128fb to properly save the PCI config space -before- it
potentially switches the PM state of the chip. This avoids a
warning with the new PM core and is the right thing to do anyway.
I also replaced the hand-coded switch to D2 with a call to the
genericc pci_set_power_state() and removed the code that switches it
back to D0 since the generic code is doing that for us nowadays.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes atyfb to properly save the PCI config space -before- it
potentially switches the PM state of the chip. This avoids a
warning with the new PM core and is the right thing to do anyway.
I also slightly cleaned up the code that checks whether we are
running on a PowerMac to do a runtime check instead of a compile
check only, and replaced a deprecated number with the proper
symbolic constant.
Finally, I removed the useless switch to D0 from resume since
the core does it for us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
list.h provides a dedicated primitive for
"list_del followed by list_add_tail"... list_move_tail.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Rename the async_*_special() functions to async_*_domain(), which
describes the purpose of these functions much better.
[Broke up long lines to silence checkpatch]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Add some kerneldoc to the async interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
If we fail to create the manager thread, fall back to non-fastboot.
If we fail to create an async thread, try again after waiting for
a bit.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
async_schedule() should pass in async_running as the running
list, and run_one_entry() should put the entry to be run on
the provided running list instead of always on the generic one.
Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
