em28xx-cards.c
- DVB support is supposed to be enabled for the first generation HVR-900.
This device was confirmed with DVB by mkrufky when we did the original work
in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, HVR900/HVR950 were incorreclty going back to analog. The
result is that only digital were working.
This patch provides the proper setup for analog/digital and tuner callback.
It also properly resets analog into a sane state at open().
Thanks to Steven Toth <stoth@linuxtv.org> and Michael Krufky <mkrufky@linuxtv.org>
for helping to set the proper parameters to GPO/GPIO em2883 ports.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, all registers will follow the same convension:
EM28XX_R<reg_number>_<reg_name>
This allows to associate a register with its value, and also with a canonical
name. Also, registers that are specific to a given chip were renamed accordingly,
as EM2800_foo (for 2800 only registers) or EM2880_foo (for registers that started
to appear on em2880).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, registers 0x04 and 0x08 were referenced by its value. This is
bad, since makes harder for someone to understand what this is doing.
This patch renames those two registers into an appropriate name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx.h contains lots of different stuff inside. The better is to break it on
some files.
This patch removes the register names, moving them to a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is more conservative than just removing the msleep() from
em28xx_write_regs_req(), since some old hardware may still need it.
So, it will remove the sleep time only for those chips where this
removal were tested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c:
- Fix reversed val/rst values in both analog_gpio and digital_gpio
vectors
- Fix crash that would was occurring during every analog startup
while looping over gpio_ctl
- Remove what appears to be a redundant setting of gpio_ctl->val
- Don't use OREN538 demodulation for the HVR-950 (prevents ATSC
scanning from working)
em28xx-dvb.c:
- Tuner should be in digital mode when issuing the reset
- Add copyright
- Change struct definition (corresponds to fix in em28xx-cards.c for
gpio_ctl looping)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Devin Heitmueller <devin.heitmueller@gmail.com> and Aidan
Thornton" <makosoft@googlemail.com> for pointing some errors with the
previous scenario.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds DVB support for Hauppauge HVR950.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for getting those values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx based devices with xc3028 may require some specific gpio values.
This patch adds a generic handling for such values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds em28xx-dvb. This driver is highly based on cx88-dvb and
saa7134-dvb.
This code currently loads and unloads successfully. However, some
changes are needed to properly support the mpeg streams and to setup
em28xx to work on DVB mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TUNER_PHILIPS_ATSC is an ambiguous name for a tuner. Rename it to
TUNER_PHILIPS_FCV1236D to be more descriptive.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
has_tuner flag doesn't make much sense, since tuner_type=TUNER_ABSENT
means the same thing.
Having two ways to say that a tuner is not present is
not nice, since it may lead to bad setups. In fact, with the previous
code, if a device were using has_tuner=0, but the user forces a tuner,
with modprobe option tuner=type, the modprobe option won't work.
Also, tveeprom returns TUNER_ABSENT, when tuner is unknown or absent.
So, with the previous logic, in this case, the driver should set
has_tuner=0, or has_tuner=1 otherwise.
Instead of adding several additional tests and setups, better just to
remove .has_tuner.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only HVR950 has analog_gpio configured. It makes no sense to set gpio to 0 for
other boards. Better to add a test, while this var is not set for all xc3028
devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Markus Rechberger <mrechberger@gmail.com> for retriving those
commands.
Also, MTS firmware is required for audio to work on HVR950.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch below adds the "Pinnacle Dazzle DVC 100" to the list of
cards supported by the em28xx driver. As the configuration is the same
as the DVC 90 one, it simply adds a new USB ID to the list of devices
supported by the DVC 90 configuration.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xc2028.3028 has two type of firmwares: audio-standard specific ones and
baseband MTS firmwares. MTS firmwares provide stereo decoding for 6 MHz
BTSC/EIAJ and for monoaural audio decoding on 8 MHz firmwares.
It seems that the option to use MTS or a standard-specific audio decoding
depends on the way xc2028/3028 is connected.
Instead of wasting 32 (or 64 bits) to signalize if the driver needs to use MTS
firmware, this patch converts it to a bitfield that can be shared with other
proprieties of xc2028/3028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-900 requires the MTS version of the xc3028 firmware in order
to get any sound. The below patch selects this firmware variant on
HVR-900 cards, as well as splitting the HVR-950 into its own entry
(since I don't know if it uses the MTS variant and it will have to be
split off eventually anyway).
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the conversion to the vidio_ioctl2, tvnorms array is not required anymore.
Also, removed some code from V4L1 time (VIDEO_MODE_foo), specied at the
non-used video_decoder.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hauppauge firmwares can be decoded using tveeprom. This patch adds HVR-900 as
a tveeprom client. It also adds xc3028 tuner entry to tveeprom.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds autodetection support for the Cinergy200 USB and the VGear PocketTV.
Whenever a usb device with generic empia em2800 usb ids is detected the device
gets scanned for connected i2c devices. If the device list matches an em2800
device in the device list the model id gets changed accordingly.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
attached patch adds support for the vgear pockettv.
It seems to require a write to another register for audio to work.
I checked my old cinergydrv and we did the same register write there. I
therefore enabled it for all em2800 based devices.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a function to allow trying to detect boards that shares
the generic IDs.
The current detection method is based at eeprom checksum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds USB ID for HVR-950. It also adds the callback for handling
firmware loading.
Thanks to Markus Reichberger for the reset commands.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also replaces all occurrences of TUNER_XCEIVE_XC3028 to TUNER_XC2028.
Some work is still may be required to make sure that non-tm6000 drivers will
be capable of using tuner-xc2028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following possible cleanups:
- make the following needlessly global functions static:
- em28xx-core.c: em28xx_accumulator_set()
- em28xx-core.c: em28xx_capture_area_set()
- em28xx-core.c: em28xx_scaler_set()
- em28xx-core.c: em28xx_isocIrq()
- remove the following unused EXPORT_SYMBOL's:
- em28xx-cards.c: em28xx_boards
- em28xx-cards.c: em28xx_bcount
- em28xx-cards.c: em28xx_id_table
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
