spectrum_cs: Fix the logic so we error when the device is *not* present!
This fixes firmware upload failures which prevent the driver from
working (the bug is also present in 2.6.17).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to. If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
while playing with gcc 4.1 -Wextra warnings, I came across this one:
drivers/net/3c515.c:1027: warning: comparison of unsigned expression >= 0 is always true
Since i is unsigned the >= 0 check in the for loop is always true,
so we might spin there forever unless the if condition triggers.
Since i is only used in this loop, this patch changes it to
an integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.
Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade. Update the Arbel versions as well while we are at it.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Intersil firmware 1.7.4 (and possibly others) loses the antenna
selection settings when the port is reset.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced during the PCMCIA API conversion and broke
spectrum_cs completely.
Tracked down by Fredrik Tolf <fredrik@dolda2000.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in commit 3d0f0fa0cb:
bounds checking is performed against period[32] while indexing delay[4].
Spotted by Coverity, CID 1376.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move out PCS handling from piix_sata_prereset() into
piix_sata_present_mask() and use it from newly implemented
piix_sata_softreset(). Class codes for devices which are indicated to
be absent by PCS are cleared to ATA_DEV_NONE. This fixes ghost device
problem reported on ICH6 and 7.
This patch moves PCS handling from prereset to softreset, which makes
two behavior changes.
* perform softreset even when PCS indicates no device
* PCS handling is repeated before retrying softresets due to reset
failures.
Both behavior changes are intended and more consistent with how other
drivers behave.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
One of my recent changes broke C101 carrier handling, this patch
fixes it. Also fixes an old TX underrun checking bug.
2.6.18 material. Please apply.
Thanks.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should update the fs_enet infrastructure to utilize Phy Abstraction
Layer subsystem. Along with the above, there are apparent bugfixes, overhaul
and improvements.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
qeth: bhs must be disabled when accessing neighbour tables.
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@axis.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool -g (show ring sizes) support to the Spidernet network driver.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unclear how these bugs arrived, presumably from incorrect cleanup of
the 16-bit-only paths, but smc91x wouldn't build for OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like broken BIOSes controlling Rhine chips will remain in use in
significant numbers; such systems fail to come up via PXE after they have
been put into D3 (power-saving) mode.
This patch adds a module option for disabling the call that puts the chip
to sleep.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Joerg Bashir <brak@archive.org>
Cc: Tim Phipps <tim@phipps-hutton.freeserve.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When booting using root-nfs, I'm seeing (independently) two lockdep dumps
in the smc91x driver. The patch below fixes both. Both dumps look like
real locking issues.
Nico - please review and ack if you think the patch is correct.
Dump 1:
Sending DHCP requests .
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The poll_enable should be in init_registers before enabling interrupts, not
in tx_timeout. Thanks for spotting it Roger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cc: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x driver forgets to release the spinlock on spurious interrupts.
This little patch fixes it.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add netconsole support to dm9000 driver.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sparc32:
drivers/net/s2io.c:2636: warning: implicit declaration of function 'disable_irq'
drivers/net/s2io.c:2656: warning: implicit declaration of function 'enable_irq'
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/sundance.c:110: error: version causes a section type conflict
I don't understand this error. It's referred to from both __init and
__devinit code. With CONFIG_HOTPLUG=n, version[] is placed in .init.data and
is referred to from .init.text.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With CONFIG_HOTPLUG=n it won't compile:
distcc[25607] ERROR: compile drivers/net/fealnx.c on g5/64 failed
version[] is referred to from both __init code and from __devinit code, so
move it out of __init altogether.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With CONFIG_HOTPLUG=n it won't compile:
drivers/net/tulip/winbond-840.c:141: error: version causes a section type conflict
(For some reason it gets the same error if marked __initdata. Give up.)
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/seeq8005.o - Section mismatch: reference to .init.text:seeq8005_probe from .text between 'init_module' (at offset 0x106) and 'seeq8005_open'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ni65.o - Section mismatch: reference to .init.text:ni65_probe from .text between 'init_module' (at offset 0x54a) and 'ni65_stop_start'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xfd) and 'wd_open'
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x14b) and 'wd_open'
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.data:wd_portlist from .text between 'init_module' (at offset 0x17f) and 'wd_open'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/tokenring/smctr.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x2ba0) and 'smctr_reset_adapter'
WARNING: drivers/net/tokenring/smctr.o - Section mismatch: reference to .init.text:smctr_probe from .text between 'init_module' (at offset 0x2bf4) and 'smctr_reset_adapter'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x6e6) and 'ibmtr_probe_card'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x74a) and 'ibmtr_probe_card'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x7fd) and 'ibmtr_probe_card'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ni52.o - Section mismatch: reference to .init.text:ni52_probe from .text between 'init_module' (at offset 0x997) and 'ni52_close'
WARNING: drivers/net/ni65.o - Section mismatch: reference to .init.text:ni65_probe from .text between 'init_module' (at offset 0x54a) and 'ni65_stop_start'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/lne390.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x100) and 'lne390_close'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/lance.o - Section mismatch: reference to .init.data:lance_portlist from .text between 'init_module' (at offset 0x8d3) and 'lance_purge_ring'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x6d2) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x6ef) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x702) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x70e) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x71d) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x729) and 'eth16i_multicast'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/es3210.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xdf) and 'es_close'
WARNING: drivers/net/es3210.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x100) and 'es_close'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eexpress.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x6c3) and 'eexp_hw_lasttxstat'
WARNING: drivers/net/eexpress.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x74f) and 'eexp_hw_lasttxstat'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x284) and 'eepro_ethtool_get_drvinfo'
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x2a7) and 'eepro_ethtool_get_drvinfo'
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.data:eepro_portlist from .text between 'init_module' (at offset 0x2b3) and 'eepro_ethtool_get_drvinfo'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/e2100.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xd9) and 'e21_reset_8390'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/at1700.o - Section mismatch: reference to .init.text:at1700_probe from .text between 'init_module' (at offset 0x75) and 'net_get_stats'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.data:version from .text between 'init_module' (at offset 0x13d8) and 'net_get_stats'
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x1634) and 'net_get_stats'
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x1a1f) and 'net_get_stats'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/appletalk/cops.o - Section mismatch: reference to .init.text:cops_probe from .text between 'init_module' (at offset 0xae) and 'cops_rx'
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ac3200.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xf9) and 'ac_close_card'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/82596.o - Section mismatch: reference to .init.text:i82596_probe from .text between 'init_module' (at offset 0x141) and 'i596_add_cmd'
Also nail a couple of crazy inlines.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stall error handler if attempting resets/aborts while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Background:
Although the transport is using the scsi_timed_out functionality to
restart the timeout if the rport is blocked, if the timeout has already
fired before the block occurs, the eh handler still runs and can take
the device offline. Ultimately, this window cannot be resolved without
significant work in the error handler thread. Christoph noted the first
level of these issues when he noted the poor error response handling
by the error thread.
We found, under heavy load and error testing, that time window from when
the scsi_times_out() adds the io to the queue to when the scsi_error_handler
gets around to servicing it, can be in the several seconds range. In most
cases, these test conditions are highly unusual, but possible.
As a result, we're stalling the error handler in this race window so that
we can avoid the device_offline transitions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Bug Fixes:
- Cap MBX_DOWN_LINK command timeout to 60 seconds
- Fix double free of ndlp object
- Don't free mbox structures on error. The completion handlers expect to do so.
- Clear host attention work items when going offline
- Fixed discovery issues in multi-initiator environments.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Leave all SRQ methods out of the device's uverbs_cmd_mask if the
device doesn't have SRQ support (because of ancient firmware) so that
we don't allow userspace to call the driver's create_srq method. This
fixes a userspace-triggerable oops caused by ib_uverbs_create_srq()
following the device's ->create_srq function pointer, which will be
NULL if the device doesn't support SRQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PPP code contains two kmalloc()s followed by memset()s without
handling a possible memory allocation failure. (Suggested by Joe
Perches).
And furthermore, conversions from kmalloc+memset to kzalloc.
[akpm@osdl.org: fix error-path leak]
[akpm@osdl.org: cleanups]
[paulus@samba.org: don't add useless printk and cardmap_destroy calls]
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dev_alloc_skb() to netdev_alloc_skb() and increase default
rx ring size to 255. The old ring size of 100 was too small.
Update version to 1.4.44.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a subtle race condition between bnx2_start_xmit() and bnx2_tx_int()
similar to the one in tg3 discovered by Herbert Xu:
CPU0 CPU1
bnx2_start_xmit()
if (tx_ring_full) {
tx_lock
bnx2_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in bnx2_tx_int() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if bnx2_tx_int() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made, very much identical to the tg3 fix:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in bnx2_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in bnx2_tx_int() before calling
netif_wake_queue().
4. Add memory barrier to bnx2_tx_avail().
5. Add bp->tx_wake_thresh which is set to half the tx ring size.
6. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT49BV6416 is locked by default, so we really need to provide
at least the unlock() operation for write and erase to work. This
patch implements both ->lock() and ->unlock() and provides a fixup
to install them when an AT49BV6416 chip is detected.
These functions are probably valid on more Atmel chips, but I believe
it's mostly obsolete ones. The AT49BV6416 is in fact obsolete, but
it's used on all current AT32STK1000 development boards.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Atmel flash chips don't have PRI information in the same format as
AMD flash chips. This patch installs a fixup for all Atmel chips that
converts the relevant PRI fields into AMD format.
Only the fields that are actually used by the command set is actually
converted. The rest are initialized to zero (which should be safe)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
While going through the code, I found out some memory leaks and potential
crashes in drivers/acpi/hotkey.c Please find the patch to fix them.
This patch does the following,
1. Fixes memory leaks in error paths of hotkey_write_config
2. Fixes freeing unallocated pointers in the error paths of hotkey_write_config
3. Uses a loop instead of linear searching for parsing the userspace
input in get_params
4. Uses array of char * instead of passing 4 pointer parameters
explicitly into the init_{poll_}hotkey_* static functions
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
After commit 12bbb2b7be, when SM LID
change or LID change MAD also has a client reregistration bit set,
only CLIENT_REREGISTER event is generated.
As a result, the sa_query module and the cache module don't update the
port information, and ULPs (e.g. IPoIB) stop working. This is the
regression we observe as compared to 2.6.17.
Rather than generate multiple events (which would have negative
performance impact), let us simply let cache and SA query respond to
reregister event in the same way as to LID and SM change events.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In some situations PAV alias devices on LPAR are not accessible.
The initialization procedure required to enable access to PAV alias
devices has to be performed per storage server subsystem and not
only once per storage server.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_page_cache should return page addresses and therefore the
cache must be created with an alignment of PAGE_SIZE.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the build options for acpiphp so that it may build without being
dependent on the ACPI_DOCK option, but yet does not allow the option of
acpiphp being built-in when dock is built as a module.
This does not change the previous patch for ACPI_IBM_DOCK Kconfig.
For the following matrix of config options, I built an i386 kernel.
Dock acpiphp should it build? confirmed
y y y y
y n y y
y m y y
m y no - acpiphp should acpiphp was
convert to m converted to m
m n y y
m m y y
n y y y
n n y y
n m y y
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is to remove noisy useless message at boot. The message is a ton of
"ACPI Exception (acpi_memory-0492): AE_ERROR, handle is no memory device"
In my emulation, number of memory devices are not so many (only 6), but,
this messages are displayed 114 times.
It is showed by acpi_memory_register_notify_handler() which is called by
acpi_walk_namespace().
acpi_walk_namespace() parses all of ACPI's namespace and execute
acpi_memory_register_notify_handler(). So, it is called for all of the
device which is defined in namespace. If the parsing device is not memory,
acpi_memhotplug ignores it due to "no match" and will parse next device.
This is normal route, not an exception.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix acpi_ac/battery boot with acpi=off
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
map/physmap.c tries to probe "cfi_probe", "jedec_probe" and "map_rom", but
map/Kconfig says it depends on MTD_CFI only.
This patch adds MTD_JEDECPROBE and MTD_ROM to the dependency condition.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Three typos in drivers/char/watchdog/Kconfig...
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add basic Machine detection to imacfb and some Ducumentation bits for
imacfb.
Signed-off-by: Edgar Hucek <hostmaster@ed-soft.at>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enabling PXA DMA for the smc91x on the logicpd pxa270 produces
unacceptable interference with the TFT panel, so disable it. Also
delete the lpd270 versions of the SMC_{in,out}[bl]() macros, as they
aren't used, since the board only supports 16bit accesses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In my quest to try and figure out why test 14 (control write) doesn't
work with my EZ-USB board, I noticed that sometimes testusb reported
no error even though the kernel log complained "byte 0 is 0 not 2" etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I write a patch for ipaq.c.
Would you like to add upstream tree ?
This patch enables a support of "SHARP W-ZERO3(WS004SH)" and "SHARP W-ZERO3[es](WS007SH)".
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
appletouch uses urb->transfer_dma after having freed the urb, this shows
up only if the system is compiled with slab debugging. This patch fixes
it by reordering the free calls.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has removed a unbalanced #endif from ohci-au1xxx.c .
Please apply before 2.6.18 release.
Error message was:
In file included from drivers/usb/host/ohci-hcd.c:909:
drivers/usb/host/ohci-au1xxx.c:113:2: #endif without #if
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as763) adds an unusual_devs entry for the A-VOX WSX-300ER MP3
player.
From: David Kuehling <dvdkhlng@gmx.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make pciehp build on powerpc
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When destroying a QP, mthca locks both the QP's send CQ and receive
CQ. However, the following scenario is perfectly valid:
QP_a: send_cq == CQ_x, recv_cq == CQ_y
QP_b: send_cq == CQ_y, recv_cq == CQ_x
The old mthca code simply locked send_cq and then recv_cq, which in
this case could lead to an AB-BA deadlock if QP_a and QP_b were
destroyed simultaneously.
We can fix this by changing the locking code to lock the CQ with the
lower CQ number first, which will create a consistent lock ordering.
Also, the second CQ is locked with spin_lock_nested() to tell lockdep
that we know what we're doing with the lock nesting.
This bug was found by lockdep.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fence bit needs to be set in the doorbell too, not just the WQE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The dasd function dasd_set_uid calls kzalloc while holding the
dasd_devmap_lock. Rearrange the code to do the memory allocation
outside the lock.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On the 88E805X chipsets (used in laptops), the PHY was not getting powered
out of shutdown properly. The variable reg1 was getting reused incorrectly.
This is probably the cause of the bug.
http://bugzilla.kernel.org/show_bug.cgi?id=6471
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
Reading the Intel VSC and AHCI it seems like writing 0x302 is incorrect.
The only valid values are 4, 1 and 0. Writing 4 disables the
PHY.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pdc_adma was overlooked and broken by the irq-pio patch:
Only HSM_ST_LAST interrupts should be delivered to this LLDD.
Adding ATA_FLAG_PIO_POLLING to pdc_adma fixes the problem (temporarily),
before we convert the irq handler of pdc_adma to handle all interrupts.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the IDE fix for Jmicron went in one piece went walking somewhere
(send log shows my end somehow). Without this sometimes you get an oops
on boot.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The request queue flush function of the dasd driver has to dequeue
the requests first and then call the end request function. Otherwise
a kernel bug in ll_rw_block.c might get triggered.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SCSI EH locks door if sdev->locked is set. Sometimes door lock
command fails continuously (e.g. when medium is not present) and as
libata uses EH to acquire sense data, this easily creates a loop where
a failed lock door invokes EH and EH issues lock door on completion.
This patch clears sdev->locked on door lock failure to break this
loop. This problem has been spotted and diagnosed by Unicorn Chang
<uchang@tw.ibm.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a sata debug print statement that still uses an old variable name.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dummy RDMA are always enabled on device startup since commit
9a71db721a (to work around buggy
PCIe chipsets which do not implement resending properly). But,
we also need to always re-enable them when resuming the device.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In bugzilla #6943, Maxim Britov reported:
"I can enable Logitech quickcam support in .config, but it want be compile.
I have to add into drivers/media/video/Makefile:
obj-$(CONFIG_USB_QUICKCAM_MESSENGER) += usbvideo/"
He's right, just enable that driver as module while disabling every other
driver that gets into that directory, nothing will get compiled.
This patch fixes the Makefile.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without the LNA these tuners perform very poorly (read 'unwatchable') when
the signal is weak.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a wrong statement order the 'standard' module option didn't
work for 'G' model chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 assembled the bytes in the wrong order.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The compat_ioctl support of the pwc driver was dropped during the last update of the driver.
I suppose it was by mistake. If yes here is the patch to restore the support.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@looxix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a subtle race condition between tg3_start_xmit() and tg3_tx()
discovered by Herbert Xu <herbert@gondor.apana.org.au>:
CPU0 CPU1
tg3_start_xmit()
if (tx_ring_full) {
tx_lock
tg3_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in tg3_tx() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if tg3_tx() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in tg3_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in tg3_tx() before calling
netif_wake_queue().
4. Change TX_BUFFS_AVAIL to an inline function with a memory barrier.
Herbert and David suggested using the memory barrier instead of
volatile.
5. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
6. Update version to 3.65.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All caller of netdev_alloc_skb need to assign skb->dev shortly
afterwards. Move it into common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove system device class for xpram. It creates the directory hierarchy
under /sys/devices/system/xpram/xpram0. The xpram0 directory is empty and
it is always created while xpram1 and following devices are always missing,
independent if the devices exist or not. Since the xpram devices are
listed in /proc/partitions and /sys/block/ as slram<x> the system device
class for xpram is meaningless.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I/O on a CCW device may stall if a channel path to that device is
logicaly varied off/on. A user I/O interrupt can get misinterpreted
as interrupt for an internal path verification operation due to a
missing check and is therefore never reported to the device driver.
Correct check for pending interruptions before starting path
verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do a retry of read device characteristics / read configuration
data when a deferred condition code 1 is encountered in
ccw_device_wake_up().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Without this patch register_tape_dev() will always fail, but might
return a value that is not an error number. This will lead to accesses
to already freed memory areas...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Another misuse of the global 'io' variable instead of the local 'base'.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch corrects a problem in mptfc which can result in targets
being removed after executing an "lsiutil 99" reset of the fibre
channel ports.
The last rescan event was being processed before the setup reset work
due to an inappropriate optimization in the event processing logic.
Every rescan event is now queued for execution and the setup reset
work now executes in the proper sequence.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based upon a conversation I had with LSI's fibre channel firmware guru,
this patch adds another condition under which the driver waits for the
firmware link initialization / target discovery to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There were some confusion about base I/O variables in the wbsd driver.
Seems like things have been working on shear luck so far. The global 'io'
variable (used when manually configuring the resources) was used instead of
the local 'base' variable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI folk forgot to fix up all the uses of 'buffer' before deleting
this struct member. Do it for them to rescue the resulting build
failures.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The hptiop just got merged with a horrible amount of really bad ioctl
code that is against the standards for new scsi drivers. This patch
backs it out (and fixes a small bug where scsi_add_host is called to
early). We can re-add proper APIs once we agree on them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fixes for zfcp's erp:
- trigger adapter reopen if do_QDIO fails
- avoid erp deadlock if registration of scsi target or remote port hang
- do not treat as error if exchange port data fails
- decrease timeout for target reset and aborts
- mark unit failed if slave_destroy is called
Additionally some code cleanup was done:
- made some functions void when retval is not of interest
- shortened initialization of zfcp's host_template
- corrected some comments
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve request handling. Use hash table to manage request IDs.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently it is impossible to reset provided by Qlogic QLA2xxx driver
SCSI devices externally using corresponding sg devices, particularly via
sg_reset utility, because qla2xxx driver in qla2xxx_eh_device_reset()
function checks if the input scsi_cmnd has its private data (CMD_SP())
attached. Then the found pointer isn't used anywhere inside of
qla2xxx_eh_device_reset(). If the RESET request comes from sg device, it
doesn't have such private data.
The attached patch removes check for non-NULL CMD_SP() from
qla2xxx_eh_device_reset(), hence allows to reset QLA2xxx's devices using
corresponding sg devices.
AV: change applies to bus/host reset handlers as well.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ID String and Message fixes
- Fix switch symbolic name registration to match cross-OS values
- Replace printk's with more standard lpfc_printf_log calls
- Make all lpfc_printf_log message numbers unique
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Short bug fixes:
- Fix iocbq list corruption due to missing list_del's in ct handling
- Missing unlock in lpfc_sli_next_iotag()
- Fix initialization of can_queue value
- Differentiate sysfs mailbox errors with different codes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix race condition between lpfc_sli_issue_mbox and lpfc_online
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix failing firmware download due to mailbox delays needing to be longer.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While busy-waiting for completion, check the hardware after scheduling;
don't schedule and then immediately check the _timeout_. If the yield()
took a long time (as it does on my OLPC prototype board when it's busy),
we'd report a timeout even though the hardware was now ready.
This fixes it, and also switches the yield() for a cond_resched() because
we don't actually want to be _that_ nice about it. I see nice
tightly-packed SMBus transactions now, rather than waiting for milliseconds
between successive phases.
Actually, we shouldn't be busy-waiting here at all. We should be using
interrupts. That's an exercise for another day though.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Christer Weinigel <wingel@nano-system.com>
Cc: <Jordan.Crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A patch in -mm kernel correct the parsing of "address resources" of pnpacpi.
Before we assumed it was memory only, but it could be also IO.
But this change show an hidden bug : some resources could be producer type
that are not handled by pnp layer. So we should ignore the producer
resources.
This patch fixes bug 6292 (http://bugzilla.kernel.org/show_bug.cgi?id=6292).
Some devices like PNP0A03 have 0xd00-0xffff and 0x0-0xcf7 as IO producer
resources.
Before correcting "address resources" parsing, it was seen as memory and was
harmless, because nobody tried to reserve this memory range as it should be
IO.
With the correction it become IO resources, and make failed all others device
that want to register IO in this range and use pnp layer (like a ISA sound
card).
The solution is to ignore producer resources
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: "Brown, Len" <len.brown@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
both of acpi_memory_enable_device() and acpi_memory_add_device() may evaluate
_CRS method.
We should avoid evaluate device's resource twice if we could get it
successfully in past.
Signed-off-by: KAMEZWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add_memory() does all necessary check to avoid collision. then, acpi layer
doesn't have to check region by itself.
(*) pfn_valid() just returns page struct is valid or not. It returns 0
if a section has been already added even is ioresource is not added.
ioresource collision check in mm/memory_hotplug.c can do more precise
collistion check.
added enabled bit check just for sanity check..
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At least Maxtor OneTouch III require a "start stop unit" command after auto
spin-down before the next access can proceed. This patch activates the
responsible code in scsi_mod for all Maxtor SBP-2 disks.
https://bugzilla.novell.com/show_bug.cgi?id=183011
Maybe that should be done for all SBP-2 disks, but better be cautious.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* MODE_MASK is unused in eicon driver.
* Conflicts with a ptrace stuff on arm.
drivers/isdn/hardware/eicon/divasync.h:259:1: warning: "MODE_MASK" redefined
include2/asm/ptrace.h:48:1: warning: this is the location of the previous definition
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Acked-by: Armin Schindler <armin@melware.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A set of tty line discipline cleanup patches were introduced before the
dawn of time, in kernel version 2.4.21. This patch performs that cleanup
for the hvsi driver.
The hvsi driver is used only on IBM pSeries PowerPC boxes. The driver was
originally written by Hollis Blanchard, who has delegated maintainership to
me. So this my first and maybe only patch in this official new role,
because this driver is otherwise bug-free :-)
Alan: "Actually its also a bug fix, tty->ldisc should be locked by refcounting
and the helpers do this for you."
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Under certain rare circumstances, it appears that there can be be a
NULL-pointer deref when a user fiddles with terminal emeulation programs while
outpu is being sent to the console. This patch checks for and avoids a
NULL-pointer deref.
Signed-off-by: Hollis Blanchard <hollisbl@austin.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix up the start up sequence.
This new sequence allow you to correctly enable the LCD controller
even if the bootloader has already did it.
- fix up a wrong indentation issue.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix "info->var.rotate" data settings.
This info should be deduced directly from "fbdev->panel->control_base"
defined into au1100fb.h.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch that allowed linear arrays to be reconfigured on-line
allowed in a bug which results in divide by zero - not all
mddev->array_size were converted to conf->array_size.
This patch finished the conversion and fixed the bug.
The offending patch was commit 7c7546ccf6.
Thanks to Simon Kirby <sim@netnation.com> for the bug report.
Cc: Simon Kirby <sim@netnation.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems like the omap-rng driver in the main tree predates the switch from
<asm/hardware/clock.h> to <linux/clk.h> ... now it builds OK.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current Linus tree crashes in aty128_set_lcd_enable() because par->pdev
is NULL. This happens since at least a week. Call trace is:
aty128_set_lcd_enable
aty128fb_set_par
fbcon_init
visual_init
take_over_console
fbcon_takeover
notifier_call_chain
blocking_notifier_call_chain
register_framebuffer
aty128fb_probe
pci_device_probe
bus_for_each_dev
driver_attach
bus_add_driver
driver_register
__pci_register_driver
aty128fb_init
init
kernel_thread
- info->fix was assigned twice.
- par->vram_size is assigned in aty128_probe(), no need to redo it again
in aty128_init()
- register_framebuffer() uses uninitialized struct members, move it past
par->pdev assignment and past aty128_bl_init().
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_PCI=n:
CC drivers/edac/edac_mc.o
drivers/edac/edac_mc.c: In function âadd_mc_to_global_listâ:
drivers/edac/edac_mc.c:1362: error: implicit declaration of function âto_platform_deviceâ
drivers/edac/edac_mc.c:1362: error: invalid type argument of â->â
drivers/edac/edac_mc.c: In function âedac_mc_add_mcâ:
drivers/edac/edac_mc.c:1467: error: invalid type argument of â->â
drivers/edac/edac_mc.c: In function âedac_mc_del_mcâ:
drivers/edac/edac_mc.c:1504: error: invalid type argument of â->â
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Juha [l
When the block queue is plugged, mq->req must be set to NULL.
Otherwise mq->req might be left non-NULL, even though mmcqd is
not processing a request, thus preventing the MMC queue thread from
being woken up when new requests do arrive.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By using milliseconds instead of jiffies to calculate acceleration
factor we make the code immune to changes in HZ.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When emulating button toggle drivers need to send input_sync()
between 'down' and 'up' events, otherwise some users might miss
keypress because device's state is only considered finalized
after EV_SYN/SYN_REPORT is received.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Trackpoint driver was not sending the magic knock sequence upon resume
causing incorrect device behavior after resuming from disk.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MX300 does not have an EXTRA_BTN - it is a simple wheel mouse with
an additional task-switcher button, which is reported as side button
(and not task button).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In the error path, ata_device_add()
* dereferences null host_set->ports[] element.
* calls scsi_remove_host() on not-yet-added shost.
This patch fixes both bugs. The first problem was spotted and initial
patch submitted by Dave Jones <davej@redhat.com>. The second problem
was mentioned and fixed by Jeff Garzik <jgarzik@pobox.com> in a larger
cleanup patch.
Cc: Dave Jones <davej@redhat.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24 doesn't make use of probe_ent->mmio_base and setting this
field causes the area to be released twice on detach. Don't set
probe_ent->mmio_base.
Signed-off-by: Tejun Heo <htejun@gmail.com>
To get host_set->private_data initialized reliably, all pinfos need to
point to the same hpriv. Restore pinfo->private_data after pata pinfo
assignment.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_prot_detach() did nothing for old EH ports and thus SCSI hosts
associated with those ports are left dangling after they are detached
leaving stale devices and causing oops eventually. Make
ata_port_detach() remove SCSI hosts for old EH ports.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Propagate acpi_processor_preregister_performance return value.
[CPUFREQ] [2/2] demand load governor modules.
[CPUFREQ] [1/2] add __find_governor helper and clean up some error handling.
[CPUFREQ] Longhaul - Rename & fix multipliers table
[CPUFREQ] Longhaul - Fix power state test to do something more useful
[CPUFREQ] Longhaul - Readd accidentally dropped line
[CPUFREQ] Make longhaul_walk_callback() static
[CPUFREQ] X86_GX_SUSPMOD must depend on PCI
[CPUFREQ] Longhaul - Initialise later.
[CPUFREQ] Longhaul - Workaround issues with APIC.
[CPUFREQ] Longhaul - Hook into ACPI C states.
[CPUFREQ] return error when failing to set minfreq
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] ahci: skip protocol test altogether in spurious interrupt code
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PNP: Add missing casts in printk() arguments
PCI: docking station: remove dock uevents
PCI: Unhide the SMBus on Asus PU-DLS
PCI Hotplug: add acpiphp to MAINTAINERS
PCI: pci/search: EXPORTs cannot be __devinit
PCIE: cleanup on probe error
pcie: fix warnings when CONFIG_PM=n
Skip protocol test altogether in spurious interrupt code. If PIOS is received
when it shouldn't, ahci will raise protocol violation.
Signed-off-by: Unicorn Chang <uchang@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When writing the firmware to the NIC, the FIFO is 256-bytes long,
so we use 256-bytes chunks and a read to wait until the previous
write is done.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent phylib from freeing PHY IRQ twice on closing an eth device:
phy_disconnect() first calls phy_stop_interrupts(), then it calls
phy_stop_machine() which in turn calls phy_stop_interrupts() making the
kernel complain on each bootup...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains some of the bug fixes and enhancements done to
s2io driver. Following are the brief description of changes
1. code cleanup to handle gso modification better
2. Move repeated code in rx path, to a common function
s2io_chk_rx_buffers()
3. Bug fix in MSI interrupt
4. clear statistics when card is down
5. Avoid linked list traversing in lro aggregation.
6. Use pci_dma_sync_single_for_cpu for buffer0 in case of 2/3
buffer mode.
7. ethtool tso get/set functions to set clear NETIF_F_TSO6
8. Stop LRO aggregation when we receive ECN notification
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains some of the bug fixes and enhancements done to
s2io driver. Following are the brief description of changes
1. Introduced macro "S2IO_PARM_INT" for declaring integer load parameter
2. UDP_RR test failure, memset txdl after Tx completion
3. PXE boot may leave adapter in unknown state so do reset in probe.
4. Add Tx completion code in netpoll
5. In s2io_vpd_read() move array vpd_data[] to pointer, saves stack memory
6. Fix bug in ethtool online test
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some resource_size_t values are fed to printk() without handling the fact
that they can have different size depending on your .config.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove uevent dock notifications. There are no consumers
of these events at present, and uevents are likely not the
correct way to send this type of event anyway.
Until I get some kind of idea if anyone in userspace cares
about dock events, I will just not send any.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unhide the SMBus controller on the Asus PU-DLS board.
This fixes bug #6763.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add acpiphp to the MAINTAINERS file.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.
Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
