When debugging is enabled, the mthca_QUERY_DEV_LIM() firmware command
function prints out some of the device limits that it queries.
However the debugging prints happen before all of the fields are
extracted from the firmware response, so some of the values that get
printed are uninitialized junk. Move the prints to the end of the
function to fix this.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert semaphores to mutexes in mthca. Leave firmware command
interface poll_sem and event_sem as semaphores.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have run into the following problem: if a task receives a signal
while in the process of e.g. destroying a resource (which could be
because the relevant file was closed) mthca could bail out from trying
to take a command interface semaphore without performing the
appropriate command to tell hardware that the resource is being
destroyed.
As a result we see messages like
ib_mthca 0000:04:00.0: HW2SW_CQ failed (-4)
In this case, hardware could access the resource after the memory has
been freed, possibly causing memory corruption.
A simple solution is to replace down_interruptible() by down() in
command interface activation.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
[ It's also not safe to bail out on multicast table operations, since
they may be invoked on the cleanup path too. So use down() for
mcg_table.sem too. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are some cards around that have UAR (user access region) size
different from 8 MB. Relax our sanity check to make sure that the PCI
BAR is big enough to access the UAR size reported by the device
firmware instead.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_create_ah() includes the port number in the GID index. The reverse
needs to be done in mthca_read_ah().
Noted by Hal Rosenstock.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
build_mlx_header() was using sqp->ud_header.grh_present before it was
initialized by mthca_read_ah(). Furthermore, header->grh_present is
set by ib_ud_header_init, so there's no need to set it again in
mthca_read_ah().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the ALIGN macro to simplify some rounding code.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix memory leaks in mthca_create_qp() and mthca_create_srq()
error handling.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert "/ (1 << lg)" to ">> lg" for a slight code size reduction.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-24 (-24)
function old new delta
mthca_map_cmd 613 589 -24
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a node_guid field to struct ib_device. It is the responsibility
of the low-level driver to initialize this field before registering a
device with the midlayer. Convert everyone to looking at this field
instead of calling ib_query_device() when all they want is the node
GUID, and remove the node_guid field from struct ib_device_attr.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out common code for initializing MAD packets, which is shared
by many query routines in mthca_provider.c, into init_query_mad().
add/remove: 1/0 grow/shrink: 0/4 up/down: 16/-44 (-28)
function old new delta
init_query_mad - 16 +16
mthca_query_port 521 518 -3
mthca_query_pkey 301 294 -7
mthca_query_device 648 641 -7
mthca_query_gid 453 426 -27
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I am seeing EQ overruns in SDP stress tests: if the CQ completion
handler arms a CQ, this could generate more EQEs, so that EQ will
never get empty and consumer index will never get updated.
This is similiar to what we have with command interface:
/*
* cmd_event() may add more commands.
* The card will think the queue has overflowed if
* we don't tell it we've been processing events.
*/
However, for completion events, we *don't* want to update the consumer
index on each event. So, perform EQ doorbell coalescing: allocate EQs
with some spare EQEs, and update once we run out of them.
The value 0x80 was selected to avoid any performance impact.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For all pages except possibly the last one, the byte beyond the buffer
end must be page aligned. Therefore, when computing the page shift to
use, OR the end addresses of the buffers as well as the start
addresses into the mask we check.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add code to modify QP operation to handle setting alternate paths for
connected QPs.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fill vendor_err field in completion with error.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Multicast group management fixes:
. Fix leak of mailbox memory in error handling on multicast group operations.
. Free AMGM indices at detach and in attach error handling.
. Fix amount to shift for aligning next_gid_index in mailbox: it
starts at bit 6, not bit 5.
. Allocate AMGM index after end of MGM table, in the range num_mgms to
multicast table size - 1. Add some BUG_ON checks to catch cases
where the index falls in the MGM hash area.
. Initialize the list of QPs in a newly-allocated group from AMGM to 0
This is necessary since when a group is moved from AMGM to MGM (in the
case where the MGM entry has been emptied of QPs), the AMGM entry is
not reset to 0 (and we don't want an extra command to do that).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
PKEY_INDEX is not a legal parameter in the RTR->RTS transition.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes to SQEr->RTS transition in modify_qp:
1. The flag IB_QP_ACCESS_FLAGS is optional for UC qps
2. The SQEr state is not supported for RC qps
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a case where copying max_inline_data from a successful create_qp
capabilities output to create_qp input could cause EINVAL error:
mthca_set_qp_size must check max_inline_data directly against
max_desc_sz; checking qp->sq.max_gs is wrong since max_inline_data
depends on the qp type and does not involve max_sg.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix mthca_create_eq for when the EQ size is not a power of 2.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modify_qp should check that the physical port number provided
is a legal value.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check error return on call to mthca_dev_lim for Tavor
(as is done for memfree).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Thinko: 64 bytes is the minimum SRQ WQE size (not the maximum).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
sae and sre bits should only be set when setting sra_max. Further, in
the old code, if the caller specifies max_rd_atomic = 0, the sre and
sae bits are still set, with the result that the QP ends up with
max_rd_atomic = 1 in effect.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch corrects some corner cases in managing the RAE/RRE bits in
the mthca qp context. These bits need to be zero if the user requests
max_dest_rd_atomic of zero. The bits need to be restored to the value
implied by the qp access flags attribute in a previous (or the
current) modify-qp command if the dest_rd_atomic variable is changed
to non-zero.
In the current implementation, the following scenario will not work:
RESET-to-INIT set QP access flags to all disabled (zeroes)
INIT-to-RTR set max_dest_rd_atomic=10, AND
set qp_access_flags = IB_ACCESS_REMOTE_READ | IB_ACCESS_REMOTE_ATOMIC
The current code will incorrectly take the access-flags value set in
the RESET-to-INIT transition.
We can simplify, and correct, this IB_QP_ACCESS_FLAGS handling: it is
always safe to set qp access flags in the firmware command if either
of IB_QP_MAX_DEST_RD_ATOMIC or IB_QP_ACCESS_FLAGS is set, so let's
just set it to the correct value, always.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When cleaning up a CQ for a QP attached to SRQ, need to free an SRQ
WQE only if the CQE is a receive completion.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
break only escapes from the innermost loop, and we want to escape both
loops and return an answer. Noticed by Ishai Rabinovitch.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only change the driver's copy of the QP attributes in modify QP after
checking the modify QP command completed successfully.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix thinko in rd_atomic calculation: ffs(x) - 1 does not find the next
power of 2 -- it should be fls(x - 1).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add limit checking on rd_atomic and dest_rd_atomic attributes:
especially for max_dest_rd_atomic, a value that is larger than HCA
capability can cause RDB overflow and corruption of another QP.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Free the memory allocated in mthca_init_user_db_tab() when releasing
the db_tab in mthca_cleanup_user_db_tab().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Unlike tavor, the max work queue size is an exact power of 2 for arbel
mode, despite what the documentation (of the QUERY_DEV_LIM firmware
command) says. Without this patch, on Arbel, we can start with a QP
of a valid size and get above the reported limit after rounding to the
next power of two.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On mem-free HCAs, when posting a long list of send requests, a
doorbell must be rung every 255 requests. Add code to handle this.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
last pointer is not updated when QP is modified to reset state. This
causes data corruption if WQEs are already posted on the queue.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Calculation of QP capabilities still isn't exactly right in mthca:
max_send_sge/max_recv_sge fields returned in create_qp can exceed the
handware supported limits.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Responder resources are only required to handle RDMA reads and atomic
operations, not RDMA writes. So the driver should allow RDMA writes
even if responder resources are set to 0. This is especially
important for the UC transport -- with the old code, it was impossible
to enable RDMA writes for UC QPs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In Tavor mode, when posting a long list of receive work requests, a
doorbell must be rung every 256 requests. Add code to do this when
required.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle case where prod_index has wrapped around and become less than
cq->cons_index by checking that their difference as a signed int is
positive rather than comparing directly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The size of work requests for atomic operations was computed
incorrectly in mthca: all sizeofs need to be divided by 16.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response. This keeps
precise knowledge of device limits in the low-level kernel driver.
This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a typo in the rearming of the catastrophic error polling timer: we
should rearm the timer as long as the stop flag is _not_ set.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Report the device's real page size capability in mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
