Add a mixer control to switch between the optical and coaxial S/PDIF
inputs on the HT-Omega Claro and Claro halo cards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable the X-Meridian's CD input and the X-Meridian 2G's potential
MIDI ports.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the generic Oxygen, use the actual card name, if known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apparently, the revision is 2 on all sold sound cards, so this
information is not actually useful.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control to select between the on-board and extension board
S/PDIF inputs for the X-Meridian (2G).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control to prevent capturing S/PDIF samples that are not
marked as valid (non-audio or corrupted samples).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce the helper function snd_ctl_enum_info() to fill out the
elem_info fields for an enumerated control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add experimental support for the Asus Xonar HDAV1.3 Slim sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add experimental support for the Asus Xonar DG sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the AuzenTech X-Meridian 7.1 2G sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the CSxxxx and AKxxxx DAC/ADC chips, the MCLK factor in double rate
modes (64-96 kHz) can be reduced to 128x without reducing sound quality.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the get_i2s_mclk callback with tables of MCLK values. This
simplifies the MCLK-handling code in both the framework and the model-
specific drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not apply the headphone gain offset to any but the front DAC. These
DACs would not be used in headphone mode, so this saves a few register
writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the DAC Oversampling mixer control because this setting does not
make much sense.
For cards with the H6 daughterboard, 128x oversampling was disabled
anyway because these high MCLK frequency would not be compatible with
the connector cable.
For cards without the H6 daughterboard, 128x gives a slightly higher
output quality; there is no reason to reduce it to 64x except for saving
power, but then these cards have not been designed to be power efficient
anyway (the D2's blinkenlights cannot be disabled).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because of the unshielded connector cable, it is important to use as low
a master clock frequency as possible with the H6.
For double rate modes (64-96 kHz), the MCLK rate is unconditionally
lowered from 512x to 256x because the higher rate would not improve
anything.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The clock output of the CS2000, which is used as master clock for the
DACs, was using half the actual master clock frequency for some reason.
Using the theoretically correct frequency seems also to work in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Xonar Essence ST Deluxe, remove all mixer controls that would
require I2C communication with the third DAC, which does not work
because of an addressing conflict with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCM format used for the PCM1796 from left-justified to I2S to
ensure that the correct format is used even for the Essence ST Deluxe's
center/LFE DAC, where I2C does not work because of an address conflict
with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM1796 needs the master clock for I2C communication to work, so
add delays after clock changes to ensure that the clock is stable when
we try to write the DACs' registers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To make the I2C communication reliable when using the H6 daughterboard,
reduce the I2C clock frequency.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix wrong register bits for SPI clock cycle times longer than 160 ns,
and adjust the polling loop timeout for these speeds.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of DACs can now be deduced from the dac_channels_mixer field,
so the private_data field is no longer needed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For cards like the Xonar HDAV1.3, differentiate between the number of
PCM channels that can be played and the number of channels whose volume
can be adjusted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
flush_scheduled_work() is deprecated and scheduled to be removed.
* cancel[_delayed]_work() + flush_scheduled_work() ->
cancel[_delayed]_work_sync().
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reformat and update the comments that describe the hardware connections
on the various models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the hardcoded "CMI8788", show the actual chip name.
Note: This is neither what the chip is (it's always the same),
nor what the chip is actually called.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To help with debugging, add the registers of the model-specific
codecs to the controller and AC97 register dump in the proc file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "Front Panel" switch on the Xonar D1/DX actually switches only the
output direction, so mark it appropriately.
The front panel microphone is controlled by the FMIC2MIC bit of the
CM9780. It was unconditionally enabled on the D1/DX and never set on
the ST(X); add a control for it. Selecting the front panel microphone
as source does not actually disable the microphone jack, but this is
bug-compatible with the Windows driver, and users rely on it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GPIO bit that enables analog output on the Xonar HDAV1.3 also
disables the HDMI audio output, so we better add a switch for it.
Hopefully, this is sufficient to make the HDMI output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the configuration of some unknown GPIO output bits (that
might not be used at all) to be the same as in the Windows driver, just
to be sure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow disabling period wakeup interrupts for all PCM streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the TempoTec/MediaTek HiFier Serenade sound card.
The PCI ID was already there, but the driver handled it like the
Fantasia model, which resulted in a dummy recording device. As
a stereo output-only card, this model is to be handled exactly
like the HG2PCI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sort the PCI IDs so that they make logical sense. Also move the card
name comments into this list because the model symbols should be (more)
self-explanationary.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Kuroutoshikou CMI8787-HG2PCI sound card.
[replaced non-latin letters in the patch by tiwai]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd-hifier driver contains more duplicated code than model-specific
code, so it does not make sense for it to be a separate driver.
Handling the two-channel output restriction can be easily done in the
generic driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This board has a strange PCI SSID 13f6:ffff. Works as compabile as
MODEL_CMEDIA_REF.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Configure the PEX8111 bridge on the PCI Express cards so that the audio
DMA controller can do proper burst reads and is less likely to lose
data. This is usually done automatically, but is required on older
cards where the user has not applied the PLX firmware update.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCIe/PCI bridge initialization code to configure only the
bridge that is actually connected to the sound chip, instead of any
bridge found in the system. The new code also makes it easier to add
other bridges.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interrupt counter is independent of the buffer counter, so there are
no restrictions on the period size. Having fewer periods also makes
PulseAudio happy.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The input monitor half volume bit results in a factor of 0.5, so the
minimum scale value should be -6 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the symbol for the XCID pins, fix up a decimal/hex confusion for
the CMI8787 package ID, and add the other known package IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The anti-pop delay for the STX should be 800 ms, not 100 ms like the ST.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a PCI ID for the Xonar HDAV1.3 Slim. There is no actual support,
but the presence of the ID allows the EEPROM repair code to work for
this card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are more models without a CD input than with one, so handle this
explicitly with a device_config flag to avoid having to define a control
filter callback to filter it out.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
