The xc5000 firmware download process can be slow on certain devices.
Add a module option, "init_fw" to perform the firmware download during
xc5000_attach(), which would get the firmware download over with well
before any tune request is made.
When this option is enabled, it will reduce the time it takes to get a
signal lock during the first tune after driver load, but will add a few
seconds to the driver initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IVTV_IOC_DMA_FRAME ioctl fails to correctly 'start' the decoder. Although
yuv output will be correct, some functions which should be disabled while the
decoder is in use remain enabled. This can result in hardware registers being
corrupted, causing problems with the mpeg decoder. This patch ensures the
decoder 'start' sequence is called, disabling these functions until the
device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the yuv device may not always 'start' the decoder.
Although yuv output will be correct, some functions which should be disabled
while the decoder is in use remain enabled. This can result in hardware
registers being corrupted, causing problems with the mpeg decoder. This patch
simply moves the existing decoder 'start' sequence to earlier in the write()
handler.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the capture is scaled, then the video_temporal_filter is set to 0
by the cx2341x.c module since otherwise you would get ghosting.
However, this was also done in the VIDIOC_S_FMT ioctl which meant that
the video_temporal_filter control was reset to 0 or 8 each time S_FMT
was called. This was old code that should have been removed a long time
ago.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This avoids the need of memsets in the ivtv/cx18 drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: convert driver to use video_ioctl2(). Pushed down ioctl debug
messages and priority checks as well. Still left serialization lock in
place for now. #if 0'ed out sliced vbi ioctl code for now.
Patch heavily based on similar changes made to ivtv by Hans Verkuil.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Based on an initial conversion patch from Douglas Landgraf.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of V4L drivers have a mod param to specify their preferred minors.
This is because it is often desirable for applications to have a static /dev
name for a particular device. However, using minors has several disadvantages:
1) the requested minor may already be taken
2) using a mod param is driver specific
3) it requires every driver to add a param
4) requires configuration by hand
This patch introduces an "index" attribute that when combined with udev rules
can create static device paths like this:
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video0
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video1
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video2
$ ls -la /dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video0
lrwxrwxrwx 1 root root 12 2008-04-28 00:02 /dev/v4l/by-path/pci-0000:00:1d.2-usb-0:1:1.0-video0 -> ../../video1
These paths are steady across reboots and should be resistant to rearranging
across Kernel versions.
video_register_device_index is available to drivers to request a
specific index number.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Kees Cook <kees@outflux.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the bundled remote control of the TT DVB-C 1501
Thanks-to: SG <SiestaGomez@web.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed some obsolete definitions and one unused variable.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The build option, MEDIA_TUNER_CUSTOMIZE, allows us to disable tuner drivers
that would have otherwise been selected by default. This is an advanced
customization option that should be disabled by default.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Auto-selects tda10023, for budget-ci, if !DVB_FE_CUSTOMISE. This is needed for
Technotrend budget C-1501 dvb board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following experimental patch adds support for the technotrend budget
C-1501 dvb-c card. The parameters used to configure the tda10023 demod
chip are largely determined experimentally, but works quite for me in my
initial tests.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in bttv-i2c. For one thing, a
real template is supposed to be read-only. And in some cases it's more
efficient to initialize the few fields we need individually.
This clean-up shrinks bttv-i2c.o by 29% (x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in zoran_card. For one thing,
a real template is supposed to be read-only. And in some cases it's
more efficient to initialize the few fields we need individually.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- support for Anysee E30C Plus rev 0.4
- set IO port E
- set correct TS mode
- change deltaf according to latest Windows driver
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Split the Beholder M6 family to different models. Because M6 hasn`t RDS, M63
has chip with AC3 codec, M6 Extra has other type of HF module.
Add correct data for support MPEG encoder.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework saa7134_enable_i2s function. Remove vendor specific data.
Configure I2S output port specific for model of SAA7133/5-SAA7134.
I think it is more good.
Renamed definition of I2S audio output control register. It`s SAA7133/5 register
Start video port after configuring procedure.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Separate the newer variant of the HVR-900 into its own device profile
because it has a Micronas DRX397 instead of the Zarlink demod. This
doesn't make the device work, but at least we don't try to initialize it
as though it had the Zarlink device.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
[mchehab@infradead.org: avoid compilation breakage at mainstream, where drx397xD.h doesn't exist yet]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- this now finally adds hardware frequency seek support
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- afc indication:
device has no indication whether freq is too low or too high
therefore afc always return 1, when freq is wrong
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- comment on how to listen to an usb audio device
(i get so many questions about that...)
- code cleanup (error handling, more warnings, spacing, ...)
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- version bumped to 1.0.8 for all the following patches
- si470x_get_freq now returns errno
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
this patch brings the following changes:
- move the global disconnect lock into the device structure
- code cleanup (spaces to tabs, long line splits, ...)
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only one frontend is enabled right now. The second frontend can lock,
but transport doesn't work yet. The device will be supported as a
single tuner device until the second frontend is working.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This file was renamed but we forgot to change it in the comments.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- update license comments
- change MODULE_DESCRIPTION from device specific to chipset specific
- correct debug switch from deb_rc to deb_info
- correct MPEG2 stream interval from 1.25 to 1
- change frontend_attach error code from -EIO to -ENODEV
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
