* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
dsa: fix master interface allmulti/promisc handling
dsa: fix skb->pkt_type when mac address of slave interface differs
net: fix setting of skb->tail in skb_recycle_check()
net: fix /proc/net/snmp as memory corruptor
mac80211: fix a buffer overrun in station debug code
netfilter: payload_len is be16, add size of struct rather than size of pointer
ipv6: fix ip6_mr_init error path
[4/4] dca: fixup initialization dependency
[3/4] I/OAT: fix async_tx.callback checking
[2/4] I/OAT: fix dma_pin_iovec_pages() error handling
[1/4] I/OAT: fix channel resources free for not allocated channels
ssb: Fix DMA-API compilation for non-PCI systems
SSB: hide empty sub menu
vlan: Fix typos in proc output string
[netdrvr] usb/hso: Cleanup rfkill error handling
sfc: Correct address of gPXE boot configuration in EEPROM
el3_common_init() should be __devinit, not __init
hso: rfkill type should be WWAN
mlx4_en: Start port error flow bug fix
af_key: mark policy as dead before destroying
Before commit b6c40d68ff ("net: only
invoke dev->change_rx_flags when device is UP"), the dsa driver could
sort-of get away with only fiddling with the master interface's
allmulti/promisc counts in ->change_rx_flags() and not touching them
in ->open() or ->stop(). After this commit (note that it was merged
almost simultaneously with the dsa patches, which is why this wasn't
caught initially), the breakage that was already there became more
apparent.
Since it makes no sense to keep the master interface's allmulti or
promisc count pinned for a slave interface that is down, copy the vlan
driver's sync logic (which does exactly what we want) over to dsa to
fix this.
Bug report from Dirk Teurlings <dirk@upexia.nl> and Peter van Valderen
<linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dsa slave interface has a mac address that differs from that
of the master interface, eth_type_trans() won't explicitly set
skb->pkt_type back to PACKET_HOST -- we need to do this ourselves
before calling eth_type_trans().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since skb_reset_tail_pointer() reads skb->data, we need to set
skb->data before calling skb_reset_tail_pointer(). This was causing
spurious skb_over_panic()s from skb_put() being called on a recycled
skb that had its skb->tail set to beyond where it should have been.
Bug report from Peter van Valderen <linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmpmsg_put() can happily corrupt kernel memory, using a static
table and forgetting to reset an array index in a loop.
Remove the static array since its not safe without proper locking.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mac80211/debugfs_sta.c
The trailing zero was written to state[4], it's out of bounds.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing pktgen, I found that sometimes my configurations from
previous runs would be left over, particularly when going from a test
with 8 threads down to a test with 4 threads.
This adds new functionality to pktgen where you can call
pgset "reset"
and it will be just like you just insmod'ed pktgen again.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
payload_len is a be16 value, not cpu_endian, also the size of a ponter
to a struct ipv6hdr was being added, not the size of the struct itself.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of cleanup operations in the error/exit section of ip6_mr_init()
is completely inversed. It should be the other way around.
Also a del_timer() is missing in the error path.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As regulatory_request gets bigger there will be more questions
of what things means, so clarify documenation for it and
keep track of the special alpha2 codes we use internally
and on the userspace regulatory agents.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are certain scenerios where we require intersecting
two regulatory domains. This adds intersection support.
When we enable 802.11d support we will use this to intersect
the regulatory domain from the AP's country IE and what our
regulatory agent believes is correct for a country.
This patch enables intersection for now in the case where
the last regdomain was set by a country IE which was parsed
and the user then wants to set the regulatory domain. Since
we don't support country IE parsing yet this code path will not
be hit, however this allows us to pave the way for 11d support.
Intersection code has been tested in userspace with CRDA.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regulatory rule is invalid when the frequency difference
between the end of the frequency range and the start is 0.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the addition of basic rate set and TX queue parameter
configuration and confirmation that power save buffering is
working again, mac80211 is now in state that allows AP mode to be
used without major problems. Consequently, it is time to allow this
mode to be enabled without having to patch the kernel.
AP mode requires hostapd for management frame processing and as such,
configuring this mode is only allowed through cfg80211 (not with
iwconfig and WEXT).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In previous code all the rates were marked as basic.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_WIPHY_TXQ_PARAMS, that can be used with
NL80211_CMD_SET_WIPHY for userspace (e.g., hostapd) to set TX queue
parameters (txop, cwmin, cwmax, aifs).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_BSS_BASIC_RATES, that can be used with
NL80211_CMD_SET_BSS for userspace (e.g., hostapd) to set which rates are
in the basic rate set.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a helper function that, given a bitmap of basic
rates and a bitrate returns the response rate for this rate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two current compilation problems. They showed up
with CONFIG_IEEE80211_DEBUG defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a constant from the 802.11 specification.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch prints reason code for deauth/dissoc frames to give users
more ideas what's happened for the disconnection.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously I assumed that the receive queues of candidates don't
change during the GC. This is only half true, nothing can be received
from the queues (see comment in unix_gc()), but buffers could be added
through the other half of the socket pair, which may still have file
descriptors referring to it.
This can result in inc_inflight_move_tail() erronously increasing the
"inflight" counter for a unix socket for which dec_inflight() wasn't
previously called. This in turn can trigger the "BUG_ON(total_refs <
inflight_refs)" in a later garbage collection run.
Fix this by only manipulating the "inflight" counter for sockets which
are candidates themselves. Duplicating the file references in
unix_attach_fds() is also needed to prevent a socket becoming a
candidate for GC while the skb that contains it is not yet queued.
Reported-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use htonl rather than ntohl on a u32.
net/tipc/name_table.c:557:2: warning: cast to restricted __be32
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classifier should cover the most common use case and will work
without any special configuration.
The principle of the classifier is to directly access the
task_struct via get_current(). In order for this to work,
classification requests from softirqs must be ignored. This is
not a problem because the vast majority of packets in softirq
context are not assigned to a task anyway. For this to work, a
mechanism is needed to trace softirq context.
This repost goes back to the method of relying on the number of
nested bh disable calls for the sake of not adding too much
complexity and the option to come up with something more reliable
if actually needed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
But do it carefully so we register the loopback device after
we clear dev_boot_phase.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to setup the network namespace state before we register
the notifier. Otherwise if a network device is already registered
we get a nasty NULL pointer dereference.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/phonet/af_phonet.c:38:36: error: marked inline, but without a definition
net/phonet/pep-gprs.c:63:10: warning: incorrect type in return expression (different base types)
net/phonet/pep-gprs.c:63:10: expected int
net/phonet/pep-gprs.c:63:10: got restricted __be16 [usertype] <noident>
net/phonet/pep-gprs.c:65:10: warning: incorrect type in return expression (different base types)
net/phonet/pep-gprs.c:65:10: expected int
net/phonet/pep-gprs.c:65:10: got restricted __be16 [usertype] <noident>
net/phonet/pep-gprs.c:124:16: warning: incorrect type in assignment (different base types)
net/phonet/pep-gprs.c:124:16: expected restricted __be16 [usertype] protocol
net/phonet/pep-gprs.c:124:16: got unsigned short [unsigned] [usertype] protocol
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_policy_destroy() will oops if not dead policy is passed to it.
On error path in pfkey_compile_policy() exactly this happens.
Oopsable for CAP_NET_ADMIN owners.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's called from __init code only. And__devinit in generic networking code
is pretty strange :^)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
net/9p: fix printk format warnings
unsigned fid->fid cannot be negative
9p: rdma: remove duplicated #include
p9: Fix leak of waitqueue in request allocation path
9p: Remove unneeded free of fcall for Flush
9p: Make all client spin locks IRQ safe
9p: rdma: Set trans prior to requesting async connection ops
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
__scm_destroy() walks the list of file descriptors in the scm_fp_list
pointed to by the scm_cookie argument.
Those, in turn, can close sockets and invoke __scm_destroy() again.
There is nothing which limits how deeply this can occur.
The idea for how to fix this is from Linus. Basically, we do all of
the fput()s at the top level by collecting all of the scm_fp_list
objects hit by an fput(). Inside of the initial __scm_destroy() we
keep running the list until it is empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
> I'll have a prod at why the [hso] rfkill stuff isn't working next
Ok, I believe this is due to the addition of rfkill_check_duplicity in
rfkill and the fact that test_bit actually returns a negative value
rather than the postive one expected (which is of course equally true).
So when the second WLAN device (the hso device, with the EEE PC WLAN
being the first) comes along rfkill_check_duplicity returns a negative
value and so rfkill_register returns an error. Patch below fixes this
for me.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I have been tracking for a while a case where when the
network namespace exits the cleanup gets stck in an
endless precessess of:
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
It turns out that if you listen on a multicast address an unsubscribe
packet is sent when the network device goes down. If you shutdown
the network namespace without carefully cleaning up this can trigger
the unsubscribe packet to be sent over the loopback interface while
the network namespace is going down.
All of which is fine except when we drop the packet and forget to
free it leaking the skb and the dst entry attached to. As it
turns out the dst entry hold a reference to the idev which holds
the dev and keeps everything from being cleaned up. Yuck!
By fixing my earlier thinko and add the needed kfree_skb and everything
cleans up beautifully.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical devices are inside of network namespace and that
network namespace terminates we can not make them go away. We
have to keep them and moving them to the initial network namespace
is the best we can do.
For virtual devices left in a network namespace that is exiting
we have no need to preserve them and we now have the infrastructure
that allows us to delete them. So delete virtual devices when we
exit a network namespace. Keeping the necessary user space clean up
after a network namespace exits much more tractable.
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
