Commit Graph

36 Commits

Author SHA1 Message Date
Jarkko Nikula
d2c0bdaa93 ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
The McBSP1 port in OMAP3 processors (I believe OMAP2 too but I don't have
specifications to check it) have additional CLKR and FSR pins for McBSP1
receiver. Reset default is that receiver is using bit clock and frame
sync signal from those pins but it is possible to configure to use
also CLKX and FSX pins as well. In fact, other McBSP ports are doing that
internally that transmitter and receiver share the CLKX and FSX.

Add functionaly that machine drivers can set the CLKR and FSR sources by
using the snd_soc_dai_set_sysclk.

Thanks to "Aggarwal, Anuj" <anuj.aggarwal@ti.com> for reporting the issue.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-28 18:36:43 +01:00
Jarkko Nikula
d09a2afc93 ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
Functionality of functions omap_mcbsp_xmit_enable and omap_mcbsp_recv_enable
can be merged into omap_mcbsp_start and omap_mcbsp_stop since API of
those omap_mcbsp_start and omap_mcbsp_stop was changed recently allowing
to start and stop individually the transmitter and receiver.

This cleans up the code in arch/arm/plat-omap/mcbsp.c and in
sound/soc/omap/omap-mcbsp.c which was the only user for those removed
functions.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25 10:20:48 +01:00
Jarkko Nikula
32080af7a6 ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
Commit ca6e2ce086 is setting up few XCCR and
RCCR bits for I2S and DPS_A formats. Part of the bits are already set
for all formats and I believe that XDISABLE and RDISABLE bits are
format independent.

As XCCR and RCCR are found only from OMAP2430 and OMAP34xx, I move setup
of XDISABLE and RDISABLE to where those cpu's are tested and remove format
dependent part for simplicity.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-25 10:20:48 +01:00
Eduardo Valentin
a0a499c579 ASoC: OMAP: Use DMA operating mode of McBSP
Configures DMA sync mode depending on McBSP operating mode value.
The value is configurable by McBSP instance. So, depending
on McBSP operating mode, the DMA sync mode is passed from
omap-mcbsp to omap-pcm. Besides that, it also configures
McBSP threshold value depending on which McBSP mode is activated.

Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20 20:10:29 +01:00
Eduardo Valentin
caebc0cb3b ASoC: OMAP: Use McBSP threshold to playback and capture
This patch changes the way DMA is done in omap-pcm.c
in order to reduce power consumption. There is no need
to have so much SW control in order to have DMA in idle
state during audio streaming. Configuring McBSP threshold value
and DMA to FRAME_SYNC are sufficient.

Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20 20:10:29 +01:00
Eero Nurkkala
ca6e2ce086 ASoC: Always syncronize audio transfers on frames
All these steps are required for ASoC to behave correctly.
rccr and xccr are format dependent, for example TDM audio
has different values than I2S or DSP_A. Also the
omap_mcbsp_xmit_enable and/or omap_mcbsp_recv_enable must
be called right after the DMA has started.
This provides no longer L and R channels switching at random.

Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20 20:10:29 +01:00
Eero Nurkkala
c721bbdad7 ASoC: Add runtime check for RFIG and XFIG
This is, no RFIG or XFIG (Not defined in 34xx), correct
initiliazation of rccr and xccr.

Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-20 20:10:28 +01:00
Jarkko Nikula
c12abc012e ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop
Simultaneous audio playback and capture on OMAP1510 can cause that second
stream is stalled if there is enough delay between startup of the audio
streams.

Current implementation of the omap_mcbsp_start is starting both transmitter
and receiver at the same time and it is called only for firstly started
audio stream from the OMAP McBSP based ASoC DAI driver.

Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is
missed if there is no DMA transfer set up at that time when the first word
after McBSP startup is transmitted. The problem hasn't noted before since
later OMAPs are using level sensitive DMA request lines.

Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by
allowing to start and stop individually McBSP transmitter and receiver
logics. Then call those functions individually for both audio playback
and capture streams. This ensures that DMA transfer is setup before
transmitter or receiver is started.

Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem
analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA
request line behavior differences between the OMAP generations.

Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 10:57:42 +01:00
Peter Ujfalusi
31a00c6b7c ASoC: OMAP: Add 4 channel support to mcbsp
Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-23 16:11:17 +01:00
Mark Brown
9b5b0c0159 Merge branch 'for-2.6.30' into for-2.6.31 2009-04-20 12:45:40 +01:00
Jarkko Nikula
b08f7a62ca ASoC: OMAP: Update contact addresses
My email address is going to expire soon so update it. Adding also
Peter Ujfalusi <peter.ujfalusi@nokia.com> as a second contact to OMAP core
drivers since I won't have anymore access to non-public OMAP documentation
in the future and Peter is working with these drivers as well.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-17 15:55:09 +01:00
Mark Brown
8d98f2246d Merge branch 'for-2.6.30' into for-2.6.31 2009-04-16 14:14:35 +01:00
Peter Ujfalusi
3ba191ce05 ASoC: OMAP: Add DSP_A mode support for mcbsp
DSP_A mode is similar to the DSP_B, but the MSB is delayed with
one bclk (appears after the FS pulse and not under it).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-16 14:04:10 +01:00
Peter Ujfalusi
c29b206ffd ASoC: OMAP: Use single-phase for DSP mode
Use single-phase mode for the DSP mode and keep the dual phase
mode for the I2S mode.

The mono (1 channel) mode already used single phase mode,
now it is more cleaner. There is no need to configure the
second phase, when the single phase is used.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-16 14:04:09 +01:00
Jarkko Nikula
36ce858245 ASoC: OMAP: Fix DSP_B format in OMAP McBSP DAI driver
The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a6c.

Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with  FWID(0).

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-16 13:37:26 +01:00
Jarkko Nikula
6984992bf0 ASoC: OMAP: Set minimum buffer size constraint for McBSP2 in OMAP3
McBSP2 in OMAP3 has 1 ksample (1k x 32 bit) internal FIFO. During
initial playback startup, this FIFO is keeping the DMA request active
until the FIFO is full.

So now if ALSA buffer size is smaller, DMA is looping around it while
filling up the HW FIFO, generating burst of interrupts as well and SW
doesn't have any change to fill enough data.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-02 16:34:17 +01:00
Eric Miao
6335d05548 ASoC: make ops a pointer in 'struct snd_soc_dai'
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.

The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-03-04 22:29:47 +00:00
Misael Lopez Cruz
ef390c0b6e ASoC: OMAP: Initialize XCCR and RCCR registers in McBSP DAI driver
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.

This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f859 from linux-omap-2.6
tree).

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-29 13:17:45 +00:00
Jarkko Nikula
bd25867a6c ASoC: Fix incorrect DSP format in OMAP McBSP DAI and affected drivers
- OMAP McBSP DAI driver claims to support DSP_A format which has 1-bit data
  delay but configures link for 0-bit data delay which is in fact DSP_B
- Fix this by changing format from DSP_A to DSP_B
- Fix also TLV320AIC23 codec and OSK5912 machine drivers since the same
  error is populated also there

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-22 16:15:20 +00:00
Takashi Iwai
f73f2a6a23 ALSA: ASoC - Fix symbol conflicts in omac-mcbsp.c
Add snd_ prefix to avoid the conflict of symbols in omac-mcbsp.c:
  sound/soc/omap/omap-mcbsp.c:503: error: static declaration of 'omap_mcbsp_init' follows non-static declaration
  arch/arm/plat-omap/include/mach/mcbsp.h:373: error: previous declaration of 'omap_mcbsp_init' was here

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-12-10 07:59:33 +01:00
Takashi Iwai
c9b3a40ff2 ALSA: ASoC - Fix wrong section types
The module init entries should be __init instead of __devinit.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-12-10 07:47:22 +01:00
Mark Brown
3f4b783cfd ASoC: Register platform DAIs
Register all platform DAIs with the core.  In line with current behaviour
this is done at module probe time rather than when the devices are probed
(since currently that only happens as the entire ASoC card is registered
except for those drivers that currently implement some kind of hotplug).
Since the core currently ignores DAI registration this has no practical
effect.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09 10:49:27 +00:00
Jarkko Nikula
375e8a7c94 ASoC: OMAP: Add support for mono audio links in McBSP DAI
Patch adds support for mono audio links so that McBSP DAI can operate with
real mono codecs. In I2S, the signalling remains the same but only first
frame (left channel) is transmitting audio data and second frame having null
data. In DSP_A, only first frame is transmitted.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-25 15:21:26 +00:00
Mark Brown
3ba9e10a6d ASoC: Remove DAI type information
DAI type information is only ever used within ASoC in order to special
case AC97 and for diagnostic purposes. Since modern CPUs and codecs
support multi function DAIs which can be configured for several modes
it is more trouble than it's worth to maintain anything other than a
flag identifying AC97 DAIs so remove the type field and replace it with
an ac97_control flag.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-24 18:01:31 +00:00
Jarkko Nikula
0c758bdd67 ASoC: OMAP: Fix preprocessor filled DAI name in McBSP DAI
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-21 14:35:06 +00:00
Mark Brown
dee89c4d94 ASoC: Merge snd_soc_ops into snd_soc_dai_ops
Liam Girdwood's ASoC v2 work avoids having two different ops structures
for DAIs by merging the members of struct snd_soc_ops into struct
snd_soc_dai_ops, allowing per DAI configuration for everything.
Backport this change.

This paves the way for future work allowing any combination of DAIs to
be connected rather than having fixed purpose CODEC and CPU DAIs and
only allowing CODEC<->CPU interconnections.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-21 14:12:10 +00:00
Jarkko Nikula
0b6048561d ASoC: OMAP: Add more supported sample rates into McBSP DAI driver
Originally it was put too tight limits to support only 44.1 kHz and 48 kHz
sample rates in McBSP DAI driver. Extend it now to 8 kHz - 96 kHz. With
96 kHz and 2*16 bits, bit clock is 3.072 MHz < 3.125 MHz (I2S max?).

Tested on Nokia N810 with TVL320AIC33 from rates 8 - 96 kHz and on Texas
Instruments Beagle with TWL4030 from rates 8 - 48 kHz.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-13 10:31:44 +00:00
Jarkko Nikula
da6320becf ALSA: ASoC: OMAP: Continue fixing DSP DAI format in McBSP DAI driver
Fix "ASoC: OMAP: Fix DSP DAI format in McBSP DAI driver" was not correct
due misunderstanding of DSP_A format and similar error in TLV320AIC33
codec which was used to test the original fix.

This patch corrects now DSP_A format in OMAP McBSP DAI driver and is
verified with TLV320AIC23 codec that's implementing DSP_A correctly.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-10-22 18:18:24 +02:00
Jarkko Nikula
ba9d0fd0f0 ALSA: ASoC: OMAP: Fix DSP DAI format in McBSP DAI driver
Fix word clock length which must equal to one bit clock cycle in DSP mode.
Surprisingly McBSP is able synchronize into wrong length when it's
slave but e.g. TLV320AIC33 codec in slave configuration is outputting
some amount of noise if word clock length is longer than one bit clock
cycle.

Fix also bit clock and frame sync polarities in DSP mode since they are
opposite from I2S.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-10-20 17:03:21 +02:00
Jarkko Nikula
2e89713a83 ALSA: ASoC: OMAP: Set DMA stream name at runtime in McBSP DAI driver
This suits better when adding support for multiple links and different
link formats.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-10-13 02:17:59 +02:00
Jarkko Nikula
406e2c48cf ALSA: ASoC: OMAP: Add support for OMAP2430 and OMAP34xx in McBSP DAI driver
Thanks to Arun KS <arunks@mistralsolutions.com> for fixing one typo in
original version of this patch.

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-10-13 02:17:54 +02:00
Jarkko Nikula
8def464ddd ALSA: ASoC: OMAP: Add multilink support to McBSP DAI driver
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-10-13 02:17:48 +02:00
Arun KS
3336c5b548 ALSA: ASoC: Add DSP DAI format support to the OMAP McBSP driver
Enables DSP DAI format for McBSP in OMAP platform driver

Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-10-13 02:16:59 +02:00
Russell King
a09e64fbc0 [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
This just leaves include/asm-arm/plat-* to deal with.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:55:48 +01:00
Liam Girdwood
8687eb8bde ALSA: asoc: omap - merge structs snd_soc_codec_dai and snd_soc_cpu_dai.
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the Omap platform.

Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
2008-07-10 09:32:41 +02:00
Jarkko Nikula
2e74796a45 [ALSA] ASoC: Add drivers for the Texas Instruments OMAP processors
Add common OMAP ASoC drivers and machine driver for Nokia N810. Currently
supported features are:

- Covers OMAPs from 1510 to 2420
- Common DMA driver
- DAI link driver using McBSP port in I2S mode
- Basic machine driver for Nokia N810

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-04-29 19:01:56 +02:00