fix code to access CMOS rtc registers so that it does not use inb_p and
outb_p routines, which are deprecated. Extensive research on all known
CMOS RTC chipset timing shows that there is no need for a delay in
accessing the registers of these chips even on old machines. These chipa
are never on an expansion bus, but have always been "motherboard"
resources, either in the processor chipset or explicitly on the
motherboard, and they are not part of the ISA/LPC or PCI buses, so
delays should not be based on bus timing. The reason to fix it:
1) port 80 writes often hang some laptops that use ENE EC chipsets,
esp. those designed and manufactured by Quanta for HP;
2) RTC accesses are timing sensitive, and extra microseconds may matter;
3) the new "io_delay" function is calibrated by expansion bus timing needs,
thus is not appropriate for access to CMOS rtc registers.
Signed-off-by: David P. Reed <dpreed@reed.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace the hardcoded list of initialization functions for each CPU
vendor by a list in an ELF section, which is read at initialization in
arch/x86/kernel/cpu/cpu.c to fill the cpu_devs[] array. The ELF
section, named .x86cpuvendor.init, is reclaimed after boot, and
contains entries of type "struct cpu_vendor_dev" which associates a
vendor number with a pointer to a "struct cpu_dev" structure.
This first modification allows to remove all the VENDOR_init_cpu()
functions.
This patch also removes the hardcoded calls to early_init_amd() and
early_init_intel(). Instead, we add a "c_early_init" member to the
cpu_dev structure, which is then called if not NULL by the generic CPU
initialization code. Unfortunately, in early_cpu_detect(), this_cpu is
not yet set, so we have to use the cpu_devs[] array directly.
This patch is part of the Linux Tiny project, and is needed for
further patch that will allow to disable compilation of unused CPU
support code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It becomes to early for ioremap, so we use early_ioremap
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Acked-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change Makefile so vsmp_64.o object is dependent
on PARAVIRT, rather than X86_VSMP
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Acked-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we don't need get that so early.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I found it strange that the struct sk_buff definition was found
inside the DWARF debugging sections in the generated object, so I verified
and found that there is no need for the files that bring struct sk_buff
definition into this file and verified also that sk_buff is not brought
in indirectly too, thru other headers.
I went on and removed many other unneeded includes and the end
result is:
[acme@doppio net-2.6]$ l /tmp/sys_ia32.o.before /tmp/sys_ia32.o.after
-rw-rw-r-- 1 acme acme 185240 2008-02-06 19:19 /tmp/sys_ia32.o.after
-rw-rw-r-- 1 acme acme 248328 2008-02-06 19:00 /tmp/sys_ia32.o.before
Almost 64KB only on this object file!
There were no other side effects from this change:
[acme@doppio net-2.6]$ objcopy -j "text" /tmp/sys_ia32.o.before /tmp/text.before
[acme@doppio net-2.6]$ objcopy -j "text" /tmp/sys_ia32.o.after /tmp/text.after
[acme@doppio net-2.6]$ md5sum /tmp/text.before /tmp/text.after
b7ac9b17942add68494e698e4f965d36 /tmp/text.before
b7ac9b17942add68494e698e4f965d36 /tmp/text.after
One of the complaints about using tools such as systemtap is
that one has to install the huge kernel-debuginfo package:
[acme@doppio net-2.6]$ rpm -q --qf "%{size}\n" kernel-rt-debuginfo
471737710
543867594
[acme@doppio net-2.6]$
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ tglx@linutronix.de: cleanup the other structs as well ]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The extended century readout does not solve the year 2038 problem on
32bit!
v2: Fix compilation on !ACPI, pointed out by tglx
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We assume that the RTC clock is BCD, so print a warning if it claims
to be binary.
[ tglx@linutronix.de: changed to WARN_ON - we want to know that!
If no one reports it we can remove the complete if (RTC_ALWAYS_BCD)
magic, which has RTC_ALWAYS_BCD defined to 1 since Linux 1.0 ... ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We know it is already after 2000. Use the year 2000 offset for both 32
and 64 bit, which removes ifdefs and the 1970 magic.
[ tglx@linutronix.de: remove 1970 magic, replace bogus commit message ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change size to unsigned long, becase caller and user all used unsigned long.
Also make bad_addr take an alignment parameter.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The AMD Fam10h CPUs support new Gigabyte page table entry for
mapping 1GB at a time. Use this for the kernel direct mapping.
Only done for 64bit because i386 does not support GB page tables.
This only applies to the data portion of the direct mapping; the
kernel text mapping stays with 2MB pages because the AMD Fam10h
microarchitecture does not support GB ITLBs and AMD recommends
against using GB mappings for code.
Can be disabled with disable_gbpages on the kernel command line
[ tglx@linutronix.de: simplify enable code ]
[ Yinghai Lu <yinghai.lu@sun.com>: boot fix on 256 GB RAM ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These new controls toggle experimental support for a new CPU feature,
the straightforward extension of largepages from the pmd level to the
pud level, which allows 1GB (kernel) TLBs instead of 2MB TLBs.
Turn it off by default, as this code has not been tested well enough yet.
Use the CONFIG_DIRECT_GBPAGES=y .config option or gbpages on the
boot line can be used to enable it. If enabled in the .config then
nogbpages boot option disables it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clean up the page table dumper (fix boundary conditions, table driven
address ranges, some formatting changes since it is no longer using
the kernel log but a separate virtual file), and generalize to 32
bits.
[ mingo@elte.hu: x86: fix the pagetable dumper ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds code to the kernel to have an (optional)
/proc/kernel_page_tables debug file that basically dumps the kernel
pagetables; this allows us kernel developers to verify that nothing fishy is
going on and that the various mappings are set up correctly. This was quite
useful in finding various change_page_attr() bugs, and is very likely to be
useful in the future as well.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: mingo@elte.hu
Cc: tglx@tglx.de
Cc: hpa@zytor.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unify arch/x86/mm/Makefile between 32 and 64 bits.
All configuration variables that are protected by Kconfig constraints
have been put in the common part of the Makefile; however, the NUMA
files are totally different between 32 and 64 bits and are handled via
an ifdef.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add debug information for DEBUG_PAGEALLOC to get some statistics about
the pool usage and split status.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We map a VMA for the 32-bit vDSO even when it's disabled, which is stupid.
For the 32-bit kernel it's the vdso_enabled boot parameter/sysctl
and for the 64-bit kernel it's the vdso32 boot parameter/syscall32 sysctl.
When it's disabled, we don't pass AT_SYSINFO_EHDR so processes don't use
the vDSO for anything, but we still map it. For the non-compat vDSO,
this means we're always putting an extra VMA somewhere, maybe lousing
up the control of the address space the user was hoping for.
Honor the setting by doing nothing in arch_setup_additional_pages.
[ also see: "x86 vDSO: don't use disabled vDSO for signal trampoline" ]
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the vDSO was not mapped, don't use it as the "restorer" for a signal
handler. Whether we have a pointer in mm->context.vdso depends on what
happened at exec time, so we shouldn't check any global flags now.
Background:
Currently, every 32-bit exec gets the vDSO mapped even if it's disabled
(the process just doesn't get told about it). Because it's in fact
always there, the bug that this patch fixes cannot happen now. With
the second patch, it won't be mapped at all when it's disabled, which is
one of the things that people might really want when they disable it (so
nothing they didn't ask for goes into their address space).
The 32-bit signal handler setup when SA_RESTORER is not used refers to
current->mm->context.vdso without regard to whether the vDSO has been
disabled when the process was exec'd. This patch fixes this not to use
it when it's null, which becomes possible after the second patch. (This
never happens in normal use, because glibc's sigaction call uses
SA_RESTORER unless glibc detected the vDSO.)
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
people sometimes do crazy stuff like building really large static
arrays into their kernels or building allyesconfig kernels. Give
more space to the kernel and push modules up a bit: kernel has
512 MB and modules have 1.5 GB.
Should be enough for a few years ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
http://bugzilla.kernel.org/show_bug.cgi?id=10124
this change:
commit 08f1c192c3
Author: Muli Ben-Yehuda <muli@il.ibm.com>
Date: Sun Jul 22 00:23:39 2007 +0300
x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata
This patch introduces struct pci_sysdata to x86 and x86-64, and
converts the existing two users (NUMA, Calgary) to use it.
This lays the groundwork for having other users of sysdata, such as
the PCI domains work.
The Calgary bits are tested, the NUMA bits just look ok.
replaces pcibios_scan_root by pci_scan_bus_parented...
but in pcibios_scan_root we have a check about scanned busses.
Cc: <yakui.zhao@intel.com>
Cc: Stian Jordet <stian@jordet.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The prevent_tail_call() macro works around the problem of the compiler
clobbering argument words on the stack, which for asmlinkage functions
is the caller's (user's) struct pt_regs. The tail/sibling-call
optimization is not the only way that the compiler can decide to use
stack argument words as scratch space, which we have to prevent.
Other optimizations can do it too.
Until we have new compiler support to make "asmlinkage" binding on the
compiler's own use of the stack argument frame, we have work around all
the manifestations of this issue that crop up.
More cases seem to be prevented by also keeping the incoming argument
variables live at the end of the function. This makes their original
stack slots attractive places to leave those variables, so the compiler
tends not clobber them for something else. It's still no guarantee, but
it handles some observed cases that prevent_tail_call() did not.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch also resolves hangs on boot:
http://lkml.org/lkml/2008/2/23/263http://bugzilla.kernel.org/show_bug.cgi?id=10093
The bug was causing once-in-few-reboots 10-15 sec wait during boot on
certain laptops.
Earlier commit 40d6a14662 added
smp_call_function in cpu_idle_wait() to kick cpus that are in tickless
idle. Looking at cpu_idle_wait code at that time, code seemed to be
over-engineered for a case which is rarely used (while changing idle
handler).
Below is a simplified version of cpu_idle_wait, which just makes a dummy
smp_call_function to all cpus, to make them come out of old idle handler
and start using the new idle handler. It eliminates code in the idle
loop to handle cpu_idle_wait.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc expects all toplevel assembly to return to the original section type.
The code in alteranative.c does not do this. This caused some strange bugs
in sched-devel where code would end up in the .rodata section and when
the kernel sets the NX bit on all .rodata, the kernel would crash when
executing this code.
This patch adds a .previous marker to return the code back to the
original section.
Credit goes to Andrew Pinski for telling me it wasn't a gcc bug but a
bug in the toplevel asm code in the kernel. ;-)
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In time_cpufreq_notifier() the cpu id to act upon is held in freq->cpu. Use it
instead of smp_processor_id() in the call to set_cyc2ns_scale().
This makes the preempt_*able() unnecessary and lets set_cyc2ns_scale() update
the intended cpu's cyc2ns.
Related mail/thread: http://lkml.org/lkml/2007/12/7/130
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
revert:
| commit 47001d6033
| Author: Thomas Gleixner <tglx@linutronix.de>
| Date: Tue Apr 1 19:45:18 2008 +0200
|
| x86: tsc prevent time going backwards
it has been identified to cause suspend regression - and the
commit fixes a longstanding bug that existed before 2.6.25 was
opened - so it can wait some more until the effects are better
understood.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We handle a broken tsc these days, so no need to panic. We clear the
TSC bit when tsc_init decides it's unreliable (eg. under lguest w/ bad
host TSC), leading to bogus panic.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commits:
commit 37a47db8d7
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers, fix
and
commit e3f37a54f6
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers
have been identified to cause a regression on some platforms due to
the assignement of legacy IRQs which makes the legacy devices
connected to those IRQs disfunctional.
Revert them.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=10382
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We already catch most of the TSC problems by sanity checks, but there
is a subtle bug which has been in the code for ever. This can cause
time jumps in the range of hours.
This was reported in:
http://lkml.org/lkml/2007/8/23/96
and
http://lkml.org/lkml/2008/3/31/23
I was able to reproduce the problem with a gettimeofday loop test on a
dual core and a quad core machine which both have sychronized
TSCs. The TSCs seems not to be perfectly in sync though, but the
kernel is not able to detect the slight delta in the sync check. Still
there exists an extremly small window where this delta can be observed
with a real big time jump. So far I was only able to reproduce this
with the vsyscall gettimeofday implementation, but in theory this
might be observable with the syscall based version as well.
CPU 0 updates the clock source variables under xtime/vyscall lock and
CPU1, where the TSC is slighty behind CPU0, is reading the time right
after the seqlock was unlocked.
The clocksource reference data was updated with the TSC from CPU0 and
the value which is read from TSC on CPU1 is less than the reference
data. This results in a huge delta value due to the unsigned
subtraction of the TSC value and the reference value. This algorithm
can not be changed due to the support of wrapping clock sources like
pm timer.
The huge delta is converted to nanoseconds and added to xtime, which
is then observable by the caller. The next gettimeofday call on CPU1
will show the correct time again as now the TSC has advanced above the
reference value.
To prevent this TSC specific wreckage we need to compare the TSC value
against the reference value and return the latter when it is larger
than the actual TSC value.
I pondered to mark the TSC unstable when the readout is smaller than
the reference value, but this would render an otherwise good and fast
clocksource unusable without a real good reason.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix obsolete printks in aperture-64. We used not to handle missing
agpgart, but we handle it okay now.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
right now if there's no CPU support for nmi_watchdog=2 we'll just
refuse it silently.
print a useful warning.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
implement nmi_watchdog=2 on this class of CPUs:
cpu family : 15
model : 6
model name : Intel(R) Pentium(R) D CPU 3.00GHz
the watchdog's ->setup() method is safe anyway, so if the CPU
cannot support it we'll bail out safely.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This avoids using wrmsr on MSR_IA32_DEBUGCTLMSR when it's not needed.
No wrmsr ever needs to be done if noone has ever used block stepping.
Without this change, using ptrace on 2.6.25 on an x86 KVM guest
will tickle KVM's missing support for the MSR and crash the guest
kernel. Though host KVM is the buggy one, this makes for a regression
in the guest behavior from 2.6.24->2.6.25 that we can easily avoid.
I also corrected some bad whitespace.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the problem that makedumpfile sometimes fails on x86_64 machine.
This patch adds the symbol "phys_base" to a vmcoreinfo data. The
vmcoreinfo data has the minimum debugging information only for dump
filtering. makedumpfile (dump filtering command) gets it to distinguish
unnecessary pages, and makedumpfile creates a small dumpfile.
On x86_64 kernel which compiled with CONFIG_PHYSICAL_START=0x0 and
CONFIG_RELOCATABLE=y, makedumpfile fails like the following:
# makedumpfile -d31 /proc/vmcore dumpfile
The kernel version is not supported.
The created dumpfile may be incomplete.
_exclude_free_page: Can't get next online node.
makedumpfile Failed.
#
The cause is the lack of the symbol "phys_base" in a vmcoreinfo data.
If the symbol "phys_base" does not exist, makedumpfile considers an
x86_64 kernel as non relocatable. As the result, makedumpfile
misunderstands the physical address where the kernel is loaded, and it
cannot translate a kernel virtual address to physical address correctly.
To fix this problem, this patch adds the symbol "phys_base" to a
vmcoreinfo data.
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I believe http://bugzilla.kernel.org/show_bug.cgi?id=10318 is a false
positive. There's no way in which networking will be using highmem pages
here, so it won't be taking the KM_USER0 kmap slot, so there's no point in
performing these checks.
Cc: Pawel Staszewski <pstaszewski@artcom.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Really sad. We lose almost all real-life coverage of the debug tests
with this patch. Now it will only report problems for the cases where
people actually end up using a HIGHMEM page, not when they just _might_
use one. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Took some cycles to re-read the Lguest Journey end-to-end, fix some
rot and tighten some phrases.
Only comments change. No new jokes, but a couple of recycled old jokes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Linus noticed a second bug and an uncleanliness:
- we'd return on any instruction fetch fault
- we'd use both the value of 16 and the PF_INSTR symbol which are
the same and make no sense
the cleanup nicely unifies this piece of logic.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to set up the shared_info pointer once we've mapped the real
shared_info into its fixmap slot. That needs to happen once the general
pagetable setup has been done. Previously, the UP shared_info was set
up one in xen_start_kernel, but that was left pointing to the dummy
shared info. Unfortunately there's no really good place to do a later
setup of the shared_info in UP, so just do it once the pagetable setup
has been done.
[ Stable: needed in 2.6.24.x ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
xen_irq_enable_direct and xen_sysexit were using "andw $0x00ff,
XEN_vcpu_info_pending(vcpu)" to unmask events and test for pending ones
in one instuction.
Unfortunately, the pending flag must be modified with a locked operation
since it can be set by another CPU, and the unlocked form of this
operation was causing the pending flag to get lost, allowing the processor
to return to usermode with pending events and ultimately deadlock.
The simple fix would be to make it a locked operation, but that's rather
costly and unnecessary. The fix here is to split the mask-clearing and
pending-testing into two instructions; the interrupt window between
them is of no concern because either way pending or new events will
be processed.
This should fix lingering bugs in using direct vcpu structure access too.
[ Stable: needed in 2.6.24.x ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The first page of the compound page is determined in follow_huge_addr()
but then PageCompound() only checks if the page is part of a compound page.
PageHead() allows checking if this is indeed the first page of the
compound.
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes the use of GPIO routines which are in the PCI
configuration space of the RDC321x, therefore reading/writing
to this space without spinlock protection can be problematic.
We also now request and free GPIOs and support the MGB100
board, previous code was very AR525W-centric.
Signed-off-by: Volker Weiss <volker@tintuc.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/ptrace.c:548: warning: 'ptrace_bts_get_size' defined but not used
arch/x86/kernel/ptrace.c:558: warning: 'ptrace_bts_read_record' defined but not used
arch/x86/kernel/ptrace.c:607: warning: 'ptrace_bts_clear' defined but not used
arch/x86/kernel/ptrace.c:617: warning: 'ptrace_bts_drain' defined but not used
arch/x86/kernel/ptrace.c:720: warning: 'ptrace_bts_config' defined but not used
arch/x86/kernel/ptrace.c:788: warning: 'ptrace_bts_status' defined but not used
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some early Athlon XP's and Opterons generate bogus faults on prefetch
instructions. The workaround for this regressed over .24 - reinstate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix the 3D performance drop reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=10328
fb drivers are using ioremap()/ioremap_nocache(), followed by mtrr_add with
WC attribute. Recent changes in page attribute code made both
ioremap()/ioremap_nocache() mappings as UC (instead of previous UC-). This
breaks the graphics performance, as the effective memory type is UC instead
of expected WC.
The correct way to fix this is to add ioremap_wc() (which uses UC- in the
absence of PAT kernel support and WC with PAT) and change all the
fb drivers to use this new ioremap_wc() API.
We can take this correct and longer route for post 2.6.25. For now,
revert back to the UC- behavior for ioremap/ioremap_nocache.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we could call find_max_pfn() directly instead of setup_memory() to get
max_pfn needed for mtrr trimming.
otherwise setup_memory() is called two times... that is duplicated...
[ mingo@elte.hu: both Thomas and me simulated a double call to
setup_bootmem_allocator() and can confirm that it is a real bug
which can hang in certain configs. It's not been reported yet but
that is probably due to the relatively scarce nature of
MTRR-trimming systems. ]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Wed, 26 Mar 2008 11:56:22 -0600
Jordan Crouse <jordan.crouse@amd.com> wrote:
> On 26/03/08 14:31 +0100, Stefan Pfetzing wrote:
> > Hello Jordan,
> >
> > I just tried to build your geodwdt driver for the geode watchdog. Therefore
> > I pulled your repository from http://git.infradead.org/geode.git (or more,
> > the git url).
> >
> > I tried to build the geodewdt driver as a module - which didn't work, and
> > it failed with the same problem as earlier mentioned on lkmk [1]. I also
> > checked the fix [2], but that seems to be already in your (or linus) tree -
> > and so I'm unsure what the problem is.
> >
> > [1] http://kerneltrap.org/mailarchive/linux-kernel/2008/2/17/884074
> > [2] http://kerneltrap.org/mailarchive/linux-kernel/2008/2/17/884174
> >
> > Building directly into the kernel seems to work.
> >
> > Maybe you have some idea?
>
> Hmm - that is strange. Exporting the symbols should work. I recommend
> starting over with a clean tree.
>
> CCing Andres - any thoughts?
>
> Jordan
>
Er, yeah. The patch below should fix it. This should probably go into
2.6.25.
Oops, EXPORT_SYMBOL_GPL wasn't being declared due to this header
being missing.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I have found that using SMI to change the cpu's frequency on my DELL
Latitude L400 clobbers the ECX register in speedstep_set_state, causing
unneccessary retries because the "state" variable has changed silently (GCC
assumes it is still present in ECX).
play safe and avoid gcc caching any register across IO port accesses
that trigger SMIs.
Signed-off by: <Stephan.Diestelhorst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert function comment blocks to kernel-doc notation.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While backporting 72dc67a696, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline). This caused a page reference leak, resulting in a
fairly massive memory leak.
Fix by removing the extraneous gfn_to_page() call.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Do not assume that a shadow mapping will always point to the same host
frame number. Fixes crash with madvise(MADV_DONTNEED).
[avi: move after first printk(), add another printk()]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The vmx hardware state restore restores the tss selector and base address, but
not its length. Usually, this does not matter since most of the tss contents
is within the default length of 0x67. However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted. The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.
Fix by restoring the tss length. Note that i386 had this working already.
Closes bugzilla 10246.
Signed-off-by: Avi Kivity <avi@qumranet.com>
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert
commit f62f1fc9ef
Author: Yinghai Lu <yhlu.kernel@gmail.com>
Date: Fri Mar 7 15:02:50 2008 -0800
x86: reserve dma32 early for gart
The patch has a dependency on bootmem modifications which are not .25
material that late in the -rc cycle. The problem which is addressed by
the patch is limited to machines with 256G and more memory booted with
NUMA disabled. This is not a .25 regression and the audience which is
affected by this problem is very limited, so it's safer to do the
revert than pulling in intrusive bootmem changes right now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
so use nodedata_phys directly.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix the bug reported here:
http://bugzilla.kernel.org/show_bug.cgi?id=10232
use update_memory_range() instead of add_memory_range() directly
to avoid closing the gap.
( the new code only affects and runs on systems where the MTRR
workaround triggers. )
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we have seen a little problem in rebooting Dell Optiplex 745 with the
0KW626 board. Here is a small patch enabling reboot with this board,
which forces the default reboot path it into the BIOS reboot mode.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The fault_msg text is not explictly nul terminated now in startup
assembly. Do so by converting .ascii to .asciz.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
aperture_64.c takes a piece of memory and makes it into iommu
window... but such window may not be saved by swsusp -- that leads to
oops during hibernation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this patch allows hpet=force on nVidia nForce 430 southbridge.
This patch was tested by me on my old Asus A8N-VM CSM (where bios does not
support hpet and does not advertise it via acpi entry). My nForce430 version:
lspci -nn | grep LPC
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260]
(rev a2)
Kernel 2.6.24.3 after patching and using hpet=force reports this:
dmesg | grep -i hpet
Kernel command line: root=/dev/sda8 ro vga=773 video=vesafb:mtrr:4,ywrap
vt.default_utf8=0 hpet=force
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
Time: hpet clocksource has been installed.
grep -i hpet /proc/timer_list
Clock Event Device: hpet
set_next_event: hpet_legacy_next_event
set_mode: hpet_legacy_set_mode
grep Clock /proc/timer_list (before patching)
Clock Event Device: pit
Clock Event Device: lapic
grep Clock /proc/timer_list (after patching)
Clock Event Device: hpet
Clock Event Device: lapic
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
a system with 256 GB of RAM, when NUMA is disabled crashes the
following way:
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Cannot allocate aperture memory hole (ffff8101c0000000,65536K)
Kernel panic - not syncing: Not enough memory for aperture
Pid: 0, comm: swapper Not tainted 2.6.25-rc4-x86-latest.git #33
Call Trace:
[<ffffffff84037c62>] panic+0xb2/0x190
[<ffffffff840381fc>] ? release_console_sem+0x7c/0x250
[<ffffffff847b1628>] ? __alloc_bootmem_nopanic+0x48/0x90
[<ffffffff847b0ac9>] ? free_bootmem+0x29/0x50
[<ffffffff847ac1f7>] gart_iommu_hole_init+0x5e7/0x680
[<ffffffff847b255b>] ? alloc_large_system_hash+0x16b/0x310
[<ffffffff84506a2f>] ? _etext+0x0/0x1
[<ffffffff847a2e8c>] pci_iommu_alloc+0x1c/0x40
[<ffffffff847ac795>] mem_init+0x45/0x1a0
[<ffffffff8479ff35>] start_kernel+0x295/0x380
[<ffffffff8479f1c2>] _sinittext+0x1c2/0x230
the root cause is : memmap PMD is too big,
[ffffe200e0600000-ffffe200e07fffff] PMD ->ffff81383c000000 on node 0
almost near 4G..., and vmemmap_alloc_block will use up the ram under 4G.
solution will be:
1. make memmap allocation get memory above 4G...
2. reserve some dma32 range early before we try to set up memmap for all.
and release that before pci_iommu_alloc, so gart or swiotlb could get some
range under 4g limit for sure.
the patch is using method 2.
because method1 may need more code to handle SPARSEMEM and SPASEMEM_VMEMMAP
will get
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 264245736k/268959744k available (8484k kernel code, 4187464k reserved, 4004k data, 724k init)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We recently got some of the "Desktop Form Factor" Optiplex 745's in. I
noticed that there's an entry for the SFF one's, but the BIOS model number
of the DFF differs from that of the SFF. We have been reliably
experiencing the same (as far as I can tell) reboot bug as the SFF boxes.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix visws printk format warnings:
/local/linsrc/linux-2.6.24-git15/arch/x86/mach-visws/traps.c:50: warning: format '%#lx' expects type 'long unsigned int', but argument 2 has type 'u32'
/local/linsrc/linux-2.6.24-git15/arch/x86/mach-visws/traps.c:50: warning: format '%#lx' expects type 'long unsigned int', but argument 3 has type 'u32'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
when numa disabled I got this compile warning:
arch/x86/kernel/setup64.c: In function setup_per_cpu_areas:
arch/x86/kernel/setup64.c:147: warning: the address of
contig_page_data will always evaluate as true
it seems we missed checking if the node is online before we try to refer
NODE_DATA. Fix it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
memory-less node support:
this patch uses updated dev_to_node, because dev_to_node already makes sure
it returns an online node.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move 00-INDEX entries to power/00-INDEX (and add entry for
pm_qos_interface.txt).
Update references to moved filenames.
Fix some trailing whitespace.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
quicklists cause a serious memory leak on 32-bit x86,
as documented at:
http://bugzilla.kernel.org/show_bug.cgi?id=9991
the reason is that the quicklist pool is a special-purpose
cache that grows out of proportion. It is not accounted for
anywhere and users have no way to even realize that it's
the quicklists that are causing RAM usage spikes. It was
supposed to be a relatively small pool, but as demonstrated
by KOSAKI Motohiro, they can grow as large as:
Quicklists: 1194304 kB
given how much trouble this code has caused historically,
and given that Andrew objected to its introduction on x86
(years ago), the best option at this point is to remove them.
[ any performance benefits of caching constructed pgds should
be implemented in a more generic way (possibly within the page
allocator), while still allowing constructed pages to be
allocated by other workloads. ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The code to restart syscalls after signals depends on checking for a
negative orig_ax, and for particular negative -ERESTART* values in ax.
These fields are 64 bits and for a 32-bit task they get zero-extended.
The syscall restart behavior is lost, a regression from a native 32-bit
kernel and from 64-bit tasks' behavior.
This patch fixes the problem by doing sign-extension where it matters.
For orig_ax, the only time the value should be -1 but winds up as
0x0ffffffff is via a 32-bit ptrace call. So the patch changes ptrace to
sign-extend the 32-bit orig_eax value when it's stored; it doesn't
change the checks on orig_ax, though it uses the new current_syscall()
inline to better document the subtle importance of the used of
signedness there.
The ax value is stored a lot of ways and it seems hard to get them all
sign-extended at their origins. So for that, we use the
current_syscall_ret() to sign-extend it only for 32-bit tasks at the
time of the -ERESTART* comparisons.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I figured out another ACPI related regression today.
randconfig testing triggered an early boot-time hang on a laptop of mine
(32-bit x86, config attached) - the screen was scrolling ACPI AML
exceptions [with no serial port and no early debugging available].
v2.6.24 works fine on that laptop with the same .config, so after a few
hours of bisection (had to restart it 3 times - other regressions
interacted), it honed in on this commit:
| 10270d4838 is first bad commit
|
| Author: Linus Torvalds <torvalds@woody.linux-foundation.org>
| Date: Wed Feb 13 09:56:14 2008 -0800
|
| acpi: fix acpi_os_read_pci_configuration() misuse of raw_pci_read()
reverting this commit ontop of -rc5 gave a correctly booting kernel.
But this commit fixes a real bug so the real question is, why did it
break the bootup?
After quite some head-scratching, the following change stood out:
- pci_id->bus = tu8;
+ pci_id->bus = val;
pci_id->bus is defined as u16:
struct acpi_pci_id {
u16 segment;
u16 bus;
...
and 'tu8' changed from u8 to u32. So previously we'd unconditionally
mask the return value of acpi_os_read_pci_configuration()
(raw_pci_read()) to 8 bits, but now we just trust whatever comes back
from the PCI access routines and only crop it to 16 bits.
But if the high 8 bits of that result contains any noise then we'll
write that into ACPI's PCI ID descriptor and confuse the heck out of the
rest of ACPI.
So lets check the PCI-BIOS code on that theory. We have this codepath
for 8-bit accesses (arch/x86/pci/pcbios.c:pci_bios_read()):
switch (len) {
case 1:
__asm__("lcall *(%%esi); cld\n\t"
"jc 1f\n\t"
"xor %%ah, %%ah\n"
"1:"
: "=c" (*value),
"=a" (result)
: "1" (PCIBIOS_READ_CONFIG_BYTE),
"b" (bx),
"D" ((long)reg),
"S" (&pci_indirect));
Aha! The "=a" output constraint puts the full 32 bits of EAX into
*value. But if the BIOS's routines set any of the high bits to nonzero,
we'll return a value with more set in it than intended.
The other, more common PCI access methods (v1 and v2 PCI reads) clear
out the high bits already, for example pci_conf1_read() does:
switch (len) {
case 1:
*value = inb(0xCFC + (reg & 3));
which explicitly converts the return byte up to 32 bits and zero-extends
it.
So zero-extending the result in the PCI-BIOS read routine fixes the
regression on my laptop. ( It might fix some other long-standing issues
we had with PCI-BIOS during the past decade ... ) Both 8-bit and 16-bit
accesses were buggy.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ahmed managed to crash the Host in release_pgd(), which cannot be a Guest
bug, and indeed it wasn't.
The bug was that handing a 0 as the address of the toplevel page table
being manipulated can cause the lookup code in find_pgdir() to return
an uninitialized cache entry (we shadow up to 4 top level page tables
for each Guest).
Commit 37cc8d7f96 introduced this
behaviour in the Guest, uncovering the bug.
The patch which he submitted (which removed the /4 from the index
calculation) simply ensured that these high-indexed entries hit the
early exit path of guest_set_pmd(). But you get lots of segfaults in
guest userspace as the PMDs aren't being updated.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now the TSC code handles a zero return from calculate_cpu_khz(),
lguest can simply pass through the value it gets from the Host: if
non-zero, all the normal TSC code applies.
Otherwise (or if the Host really doesn't support TSC), the clocksource
code will fall back to the slower but reasonable lguest clock.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This makes 64-bit ptrace calls setting the 64-bit orig_ax field for a
32-bit task sign-extend the low 32 bits up to 64. This matches what a
64-bit debugger expects when tracing a 32-bit task.
This follows on my "x86_64 ia32 syscall restart fix". This didn't
matter until that was fixed.
The debugger ignores or zeros the high half of every register slot it
sets (including the orig_rax pseudo-register) uniformly. It expects
that the setting of the low 32 bits always has the same meaning as a
32-bit debugger setting those same 32 bits with native 32-bit
facilities.
This never arose before because the syscall restart check never
matched any -ERESTART* values due to lack of sign extension. Before
that fix, even 32-bit ptrace setting orig_eax to -1 failed to trigger
the restart check anyway. So this was never noticed as a regression
of 64-bit debuggers vs 32-bit debuggers on the same 64-bit kernel.
Signed-off-by: Roland McGrath <roland@redhat.com>
[ Changed to just do the sign-extension unconditionally on x86-64,
since orig_ax is always just a small integer and doesn't need
the full 64-bit range ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new x86 setup code (4fd06960f1) broke booting on an old P3/500MHz
with an onboard Voodoo3 of mine. After debugging it, it turned out
to be caused by the fact that the vesa probing now asks for VBE2 data.
Disassembing the video BIOS shows that it overflows the vesa_general_info
structure when VBE2 data is requested because the source addresses for the
information strings which get strcpy'ed to the buffer lie outside the 32K
BIOS code (and hence contain long sequences of 0xff's).
E.G.:
get_vbe_controller_info:
00002A9C 60 pushaw
00002A9D 1E push ds
00002A9E 0E push cs
00002A9F 1F pop ds
00002AA0 2BC9 sub cx,cx
00002AA2 6626813D56424532 cmp dword [es:di],0x32454256 ; "VBE2"
00002AAA 7501 jnz .1
00002AAC 41 inc cx
.1:
00002AAD 51 push cx
00002AAE B91400 mov cx,0x14
00002AB1 BED47F mov si, controller_header
00002AB4 57 push di
00002AB5 F3A4 rep movsb ; copy vbe1.2 header
00002AB7 B9EC00 mov cx,0xec
00002ABA 2AC0 sub al,al
00002ABC F3AA rep stosb ; zero pad remainder
00002ABE 5F pop di
00002ABF E8EB0D call word get_memory
00002AC2 C1E002 shl ax,0x2
00002AC5 26894512 mov [es:di+0x12],ax ; total memory
00002AC9 26C745040003 mov word [es:di+0x4],0x300 ; VBE version
00002ACF 268C4D08 mov [es:di+0x8],cs
00002AD3 268C4D10 mov [es:di+0x10],cs
00002AD7 59 pop cx
00002AD8 E361 jcxz .done ; VBE2 requested?
00002ADA 8D9D0001 lea bx,[di+0x100]
00002ADE 53 push bx
00002ADF 87DF xchg bx,di ; di now points to 2nd half
00002AE1 26C747140001 mov word [es:bx+0x14],0x100 ; sw rev
00002AE7 26897F06 mov [es:bx+0x6],di ; oem string
00002AEB 268C4708 mov [es:bx+0x8],es
00002AEF BE5280 mov si,0x8052 ; oem string
00002AF2 E87A1B call word strcpy
00002AF5 26897F0E mov [es:bx+0xe],di ; video mode list
00002AF9 268C4710 mov [es:bx+0x10],es
00002AFD B91E00 mov cx,0x1e
00002B00 BEE87F mov si,vidmodes
00002B03 F3A5 rep movsw
00002B05 26897F16 mov [es:bx+0x16],di ; oem vendor
00002B09 268C4718 mov [es:bx+0x18],es
00002B0D BE2480 mov si,0x8024 ; oem vendor
00002B10 E85C1B call word strcpy
00002B13 26897F1A mov [es:bx+0x1a],di ; oem product
00002B17 268C471C mov [es:bx+0x1c],es
00002B1B BE3880 mov si,0x8038 ; oem product
00002B1E E84E1B call word strcpy
00002B21 26897F1E mov [es:bx+0x1e],di ; oem product rev
00002B25 268C4720 mov [es:bx+0x20],es
00002B29 BE4580 mov si,0x8045 ; oem product rev
00002B2C E8401B call word strcpy
00002B2F 58 pop ax
00002B30 B90001 mov cx,0x100
00002B33 2BCF sub cx,di
00002B35 03C8 add cx,ax
00002B37 2AC0 sub al,al
00002B39 F3AA rep stosb ; zero pad
.done:
00002B3B 1F pop ds
00002B3C 61 popaw
00002B3D B84F00 mov ax,0x4f
00002B40 C3 ret
(The full BIOS can be found at http://peter.korsgaard.com/vgabios.bin
if interested).
The old setup code didn't ask for VBE2 info, and the new code doesn't
actually do anything with the extra information, so the fix is to simply
not request it. Other BIOS'es might have the same problem.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich noticed that the reboot fixups went missing during
reboot.c unification.
(commit 4d022e35fd)
Geode and a few other rare boards with special reboot quirks are
affected.
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
