This patch adds a new kernel debug feature: CONFIG_DETECT_SOFTLOCKUP.
When enabled then per-CPU watchdog threads are started, which try to run
once per second. If they get delayed for more than 10 seconds then a
callback from the timer interrupt detects this condition and prints out a
warning message and a stack dump (once per lockup incident). The feature
is otherwise non-intrusive, it doesnt try to unlock the box in any way, it
only gets the debug info out, automatically, and on all CPUs affected by
the lockup.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows a valid iommu placed immediately after memory to work, to be
recognized as after the last byte of memory and not overlapping it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to ensure we dont get prempted when we clear ourself from mask when using
clustered mode genapic code.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Up to date I've been using the GS value to determine the processor number
in dumps from show_regs, however this can be cumbersome to do if you don't
have the vmlinux to verify with the address of cpu_pda, how about the
following? I considered using hard_smp_processor_id for robustness but we
already dereference current so we're already relying on MSR_GS_BASE being
sane.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When handling writes to /proc/irq, current code is re-programming rte
entries directly. This is not recommended and could potentially cause
chipset's to lockup, or cause missing interrupts.
CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the
interrupt is pending. The same needs to be done for /proc/irq handling as well.
Otherwise user space irq balancers are really not doing the right thing.
- Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for
lack of a generic name.
- added move_irq out of IRQ_BALANCE, and added this same to X86_64
- Added new proc handler for write, so we can do deferred write at irq
handling time.
- Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead
it now shows only active cpu masks, or exactly what was set.
- Provided a common move_irq implementation, instead of duplicating
when using generic irq framework.
Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off.
Tested UP builds as well.
MSI testing: tbd: I have cards, need to look for a x-over cable, although I
did test an earlier version of this patch. Will test in a couple days.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Zwane Mwaikambo <zwane@holomorphy.com>
Grudgingly-acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reset the ISA DMA controller into a known state after a suspend. Primary
concern was reenabling the cascading DMA channel (4).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the common code in x86 and x86-64's semaphore.c into a
single file in lib/semaphore-sleepers.c. The arch specific asm stubs are
left in the arch tree (in semaphore.c for i386 and in the asm for x86-64).
There should be no changes in code/functionality with this patch.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some nodes can have large holes on x86-64.
This fixes problems with the VM allowing too many dirty pages because it
overestimates the number of available RAM in a node. In extreme cases you
can end up with all RAM filled with dirty pages which can lead to deadlocks
and other nasty behaviour.
This patch just tells the VM about the known holes from e820. Reserved
(like the kernel text or mem_map) is still not taken into account, but that
should be only a few percent error now.
Small detail is that the flat setup uses the NUMA free_area_init_node() now
too because it offers more flexibility.
(akpm: lotsa thanks to Martin for working this problem out)
Cc: Martin Bligh <mbligh@mbligh.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Plug a race in TSC synchronization
We need to do tsc_sync_wait() before the CPU is set online to prevent
multiple CPUs from doing it in parallel - which won't work because TSC
sync has global unprotected state.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops. I knew I didn't have the physical versus logical cpu identifiers right
when I generated that patch. It's not nearly as bad as I feared at the time
though.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't log machine check events left over from boot. Too many BIOSes leave
bogus events in there.
This unfortunately also makes it impossible to log events that caused a
reboot. For people with non broken BIOS there is mce=bootlog
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the sparse mem changes and the kexec changes
were merged into setup.c they came in, in the wrong order.
This patch changes the order so we don't run sparse_init
which uses the bootmem allocator until we all of the
reserve_bootmem calls has been made.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch adds boundary check for the MAX_GSI_NUM. Same as the update for
i386, the patch addresses a problem with ACPI SCI IRQ. The patch corrects
the code such that SCI IRQ is skipped and duplicate entry is avoided. The
VIA chipset uses 4-bit IRQ register for internal interrupt routing, and
therefore cannot handle IRQ numbers assigned to its devices. The patch
corrects this problem by allowing PCI IRQs below 16.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sync_tsc was using smp_call_function to ask the boot processor to report
it's tsc value. smp_call_function performs an IPI_send_allbutself which is
a broadcast ipi. There is a window during processor startup during which
the target cpu has started and before it has initialized it's interrupt
vectors so it can properly process an interrupt. Receveing an interrupt
during that window will triple fault the cpu and do other nasty things.
Why cli does not protect us from that is beyond me.
The simple fix is to match ia64 and provide a smp_call_function_single.
Which avoids the broadcast and is more efficient.
This certainly fixes the problem of getting stuck on boot which was
very easy to trigger on my SMP Hyperthreaded Xeon, and I think
it fixes it for the right reasons.
Minor changes by AK
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the standard hardware page table manipulation macros.
This is possible now that linux works with all 4 levels
of the page tables.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In an uncensored copy of code from i386 to x86_64 I wound up
with inline assembly with the wrong constraints. Use input
constraints instead of output constraints.
So I know the assembler will do the right thing specify the size
of the operand lidtq and lgdtq instead of just lidt and lgdt.
Make load_segments use an input constraint, and delete the macro fun.
Without having to reload %cs like I do on i386 this code is noticeably
simpler.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids some potential stack overflows with very deep softirq callchains.
i386 does this too.
TOADD CFI annotation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Save a byte here and there. Ultimatively useless, but these things always
catch my eyes when reading the code so just fix them for now.
Also I got at least one patch fixing of them already, which gives a good
excuse.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use physical mode instead of logical mode to address more CPUs. This is also
used in the CPU hotplug case to avoid a race.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Will be obsolete with physflat.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch will create machinecheck sysdev directories per CPU. All of the
cpus still share the same ctl banks. When compiled with CONFIG_HOTPLUG_CPU,
it will also bring up/down sysdev directories as cpus go up/down. I have
tested the patch along with CONFIG_HOTPLUG_CPU option on in 2.6.13-rc1 kernel.
Minor changes by AK: remove useless unload function
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor cleanup.
Move things into their include files, remove obsolete includes, fix
indentation, remove obsolete special cases etc.
I also added the per cpu section to asm-generic/sections.h and fixed
init/main.c to use it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need to print kernel addresses there and clarify what the APIC-ID is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Does not change any semantics because numa_add_cpu checks for CPU 0 anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various code needs this information now before the actual SMP bootup. Instead
of computing it on the fly while booting the other CPUs set it up now while
initial MPtable/MADT parsing.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the x86_64 cpu hotplug changes went in it added a check in
default_do_nmi() which kills NMI delivery on any CPU but the BSP.
The NMI watchdog is brought up quite some time before the online bit is set
in num_online_cpus so this won't work very well. The nmi watchdogs on cpus
that are not BSP will never be reprogrammed and no NMIs.
Why was this check added? How does an offlined cpu receive an NMI?
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes boot up lockups on some machines where CPU apic ids don't start with
0
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 machine_power_off was disabling the local apic
and all of it's users wanted to be on the boot cpu.
So call machine_shutdown which places us on the boot
cpu and disables the apics. This keeps us in sync
and reduces the number of cases we need to worry about in
the power management code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is not safe to call set_cpus_allowed() in interrupt
context and disabling the apics is complicated code.
So unconditionally skip machine_shutdown in machine_emergency_reboot
on x86_64.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We only want to shutdown the apics if reboot_force
is not specified. Be we are doing this both
in machine_shutdown which is called unconditionally
and if (!reboot_force). So simply call machine_shutdown
if (!reboot_force). It looks like something
went weird with merging some of the kexec patches for
x86_64, and caused this.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with. Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the second time this has happened: inserting a new section requires
that we adjust the arithmetic which is used to calculate the vsyscall page's
offset.
Cc: Christoph Lameter <christoph@lameter.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new section called ".data.read_mostly" for data items that are read
frequently and rarely written to like cpumaps etc.
If these maps are placed in the .data section then these frequenly read
items may end up in cachelines with data is is frequently updated. In that
case all processors in an SMP system must needlessly reload the cachelines
again and again containing elements of those frequently used variables.
The ability to share these cachelines will allow each cpu in an SMP system
to keep local copies of those shared cachelines thereby optimizing
performance.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Christoph Lameter <christoph@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it. This is an intent for it. The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug). For BP, restore_processor_state is responsible for
restoring MTRR.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.
Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch contains the x86_64 specific changes for the new
return probe design. Changes include:
* Removing the architecture specific functions for querying a return probe
instance off a stack address
* Complete rework onf arch_prepare_kretprobe() and trampoline_probe_handler()
* Removing trampoline_post_handler()
* Adding arch_init() so that now we handle registering the return probe
trampoline instead of kernel/kprobes.c doing it
NOTE:
Note that with this new design, the dependency on calculating a pointer to
the task off the stack pointer no longer exist (resolving the problem of
interruption stacks as pointed out in the original feedback to this port.)
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that PPC64 has no-execute support, here is a second try to fix the
single step out of line during kprobe execution. Kprobes on x86_64 already
solved this problem by allocating an executable page and using it as the
scratch area for stepping out of line. Reuse that.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I believe at least for seccomp it's worth to turn off the tsc, not just for
HT but for the L2 cache too. So it's up to you, either you turn it off
completely (which isn't very nice IMHO) or I recommend to apply this below
patch.
This has been tested successfully on x86-64 against current cogito
repository (i686 compiles so I didn't bother testing ;). People selling
the cpu through cpushare may appreciate this bit for a peace of mind.
There's no way to get any timing info anymore with this applied
(gettimeofday is forbidden of course). The seccomp environment is
completely deterministic so it can't be allowed to get timing info, it has
to be deterministic so in the future I can enable a computing mode that
does a parallel computing for each task with server side transparent
checkpointing and verification that the output is the same from all the 2/3
seller computers for each task, without the buyer even noticing (for now
the verification is left to the buyer client side and there's no
checkpointing, since that would require more kernel changes to track the
dirty bits but it'll be easy to extend once the basic mode is finished).
Eliminating a cold-cache read of the cr4 global variable will save one
cacheline during the tlb flush while making the code per-cpu-safe at the
same time. Thanks to Mikael Pettersson for noticing the tlb flush wasn't
per-cpu-safe.
The global tlb flush can run from irq (IPI calling do_flush_tlb_all) but
it'll be transparent to the switch_to code since the IPI won't make any
change to the cr4 contents from the point of view of the interrupted code
and since it's now all per-cpu stuff, it will not race. So no need to
disable irqs in switch_to slow path.
Signed-off-by: Andrea Arcangeli <andrea@cpushare.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes kexec_crashdump() take a pt_regs * as an argument. This allows to
get exact register state at the point of the crash. If we come from direct
panic assertion NULL will be passed and the current registers saved before
crashdump.
This hooks into two places:
die(): check the conditions under which we will panic when calling
do_exit and go there directly with the pt_regs that caused the fatal
fault.
die_nmi(): If we receive an NMI lockup while in the kernel use the
pt_regs and go directly to crash_kexec(). We're probably nested up badly
at this point so this might be the only chance to escape with proper
information.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the x86_64 implementation of the crashkernel option. It reserves
a window of memory very early in the bootup process, so we never use
it for anything but the kernel to switch to when the running
kernel panics.
In addition to reserving this memory a resource structure is registered
so looking at /proc/iomem it is clear what happened to that memory.
ISSUES:
Is it possible to implement this in a architecture generic way?
What should be done with architectures that always use an iommu and
thus don't report their RAM memory resources in /proc/iomem?
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the x86_64 implementation of machine kexec. 32bit compatibility
support has been implemented, and machine_kexec has been enhanced to not care
about the changing internal kernel paget table structures.
From: Alexander Nyberg <alexn@dsv.su.se>
build fix
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Factor out the apic and smp shutdown code from machine_restart so it can be
called by in the kexec reboot path as well.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For one kernel to report a crash another kernel has created we need
to have 2 kernels loaded simultaneously in memory. To accomplish this
the two kernels need to built to run at different physical addresses.
This patch adds the CONFIG_PHYSICAL_START option to the x86_64 kernel
so we can do just that. You need to know what you are doing and
the ramifications are before changing this value, and most users
won't care so I have made it depend on CONFIG_EMBEDDED
bzImage kernels will work and run at a different address when compiled
with this option but they will still load at 1MB. If you need a kernel
loaded at a different address as well you need to boot a vmlinux.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The vmlinux on x86_64 does not report the correct physical address of
the kernel. Instead in the physical address field it currently
reports the virtual address of the kernel.
This is patch is a bug fix that corrects vmlinux to report the
proper physical addresses.
This is potentially a help for crash dump analysis tools.
This definitiely allows bootloaders that load vmlinux as a standard
ELF executable. Bootloaders directly loading vmlinux become of
practical importance when we consider the kexec on panic case.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When coming out of apic mode attempt to set the appropriate
apic back into virtual wire mode. This improves on previous versions
of this patch by by never setting bot the local apic and the ioapic
into veritual wire mode.
This code looks at data from the mptable to see if an ioapic has
an ExtInt input to make this decision. A future improvement
is to figure out which apic or ioapic was in virtual wire mode
at boot time and to remember it. That is potentially a more accurate
method, of selecting which apic to place in virutal wire mode.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eric W. Biederman <ebiederm@xmission.com
The following patch simply adds a shutdown method to the x86_64 i8259 code.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eric W. Biederman <ebiederm@xmission.com>
It is ok to reserve resources > 4G on x86_64 struct resource is 64bit now :)
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.12-rc6-mm1 has a few remaining synchronize_kernel()s, some (but not
all) in comments. This patch changes these synchronize_kernel() calls (and
comments) to synchronize_rcu() or synchronize_sched() as follows:
- arch/x86_64/kernel/mce.c mce_read(): change to synchronize_sched() to
handle races with machine-check exceptions (synchronize_rcu() would not cut
it given RCU implementations intended for hardcore realtime use.
- drivers/input/serio/i8042.c i8042_stop(): change to synchronize_sched() to
handle races with i8042_interrupt() interrupt handler. Again,
synchronize_rcu() would not cut it given RCU implementations intended for
hardcore realtime use.
- include/*/kdebug.h comments: change to synchronize_sched() to handle races
with NMIs. As before, synchronize_rcu() would not cut it...
- include/linux/list.h comment: change to synchronize_rcu(), since this
comment is for list_del_rcu().
- security/keys/key.c unregister_key_type(): change to synchronize_rcu(),
since this is interacting with RCU read side.
- security/keys/process_keys.c install_session_keyring(): change to
synchronize_rcu(), since this is interacting with RCU read side.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes register saving so that each register is only saved once,
and adds missing saving of %cr8 on x86-64. Some reordering so that
save/restore is more logical/safer (segment registers should be restored
after gdt).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sleep code uses wrong version of lgdt, that does the wrong thing when
gdt is beyond 16MB or so.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides an option to switch broadcast or use mask version for
sending IPI's. If CONFIG_HOTPLUG_CPU is defined, we choose not to use
broadcast shortcuts by default, otherwise we choose broadcast mode as default.
both cases, one can change this via startup cmd line option, to choose
no-broadcast mode.
no_ipi_broadcast=1
This is provided on request from Andi Kleen, since he doesnt agree with
replacing IPI shortcuts as a solution for CPU hotplug. Without removing
broadcast IPI's, it would mean lots of new code for __cpu_up() path, which
would acheive the same results.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Broadcast IPI's provide un-expected behaviour for cpu hotplug. CPU's in
offline state also end up receiving the IPI. Once the cpus become online they
receive these stale IPI's which are bad and introduce unexpected behaviour.
This is easily avoided by not sending a broadcast and addressing just the
CPU's in online map. Doing prelim cycle counts it appears there is no big
overhead and numbers seem around 0x3000-0x3900 on an average on x86 and x86_64
systems with CPUS running 3G, both for broadcast and mask version of the
API's.
The shortcuts are useful only for flat mode (where the perf shows no
degradation), and in cluster mode, its unicast anyway. Its simpler to just
not use broadcast anymore.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is a minor cleanup to the cpu sibling/core map. It is required
that this setup happens on a per-cpu bringup time.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Experimental CPU hotplug patch for x86_64
-----------------------------------------
This supports logical CPU online and offline.
- Test with maxcpus=1, and then kick other cpu's off to test if init code
is all cleaned up. CONFIG_SCHED_SMT works as well.
- idle threads are forked on demand from keventd threads for clean startup
TBD:
1. Not tested on a real NUMA machine (tested with numa=fake=2)
2. Handle ACPI pieces for physical hotplug support.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua.li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds __cpuinit and __cpuinitdata sections that need to exist past
boot to support cpu hotplug.
Caveat: This is done *only* for EM64T CPU Hotplug support, on request from
Andi Kleen. Much of the generic hotplug code in kernel, and none of the other
archs that support CPU hotplug today, i386, ia64, ppc64, s390 and parisc dont
mark sections with __cpuinit, but only mark them as __devinit, and
__devinitdata.
If someone is motivated to change generic code, we need to make sure all
existing hotplug code does not break, on other arch's that dont use __cpuinit,
and __cpudevinit.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch includes x86_64 architecture specific changes to support temporary
disarming on reentrancy of probes.
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The architecture independent code of the current kprobes implementation is
arming and disarming kprobes at registration time. The problem is that the
code is assuming that arming and disarming is a just done by a simple write
of some magic value to an address. This is problematic for ia64 where our
instructions look more like structures, and we can not insert break points
by just doing something like:
*p->addr = BREAKPOINT_INSTRUCTION;
The following patch to 2.6.12-rc4-mm2 adds two new architecture dependent
functions:
* void arch_arm_kprobe(struct kprobe *p)
* void arch_disarm_kprobe(struct kprobe *p)
and then adds the new functions for each of the architectures that already
implement kprobes (spar64/ppc64/i386/x86_64).
I thought arch_[dis]arm_kprobe was the most descriptive of what was really
happening, but each of the architectures already had a disarm_kprobe()
function that was really a "disarm and do some other clean-up items as
needed when you stumble across a recursive kprobe." So... I took the
liberty of changing the code that was calling disarm_kprobe() to call
arch_disarm_kprobe(), and then do the cleanup in the block of code dealing
with the recursive kprobe case.
So far this patch as been tested on i386, x86_64, and ppc64, but still
needs to be tested in sparc64.
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch adds the x86_64 architecture specific implementation
for function return probes.
Function return probes is a mechanism built on top of kprobes that allows
a caller to register a handler to be called when a given function exits.
For example, to instrument the return path of sys_mkdir:
static int sys_mkdir_exit(struct kretprobe_instance *i, struct pt_regs *regs)
{
printk("sys_mkdir exited\n");
return 0;
}
static struct kretprobe return_probe = {
.handler = sys_mkdir_exit,
};
<inside setup function>
return_probe.kp.addr = (kprobe_opcode_t *) kallsyms_lookup_name("sys_mkdir");
if (register_kretprobe(&return_probe)) {
printk(KERN_DEBUG "Unable to register return probe!\n");
/* do error path */
}
<inside cleanup function>
unregister_kretprobe(&return_probe);
The way this works is that:
* At system initialization time, kernel/kprobes.c installs a kprobe
on a function called kretprobe_trampoline() that is implemented in
the arch/x86_64/kernel/kprobes.c (More on this later)
* When a return probe is registered using register_kretprobe(),
kernel/kprobes.c will install a kprobe on the first instruction of the
targeted function with the pre handler set to arch_prepare_kretprobe()
which is implemented in arch/x86_64/kernel/kprobes.c.
* arch_prepare_kretprobe() will prepare a kretprobe instance that stores:
- nodes for hanging this instance in an empty or free list
- a pointer to the return probe
- the original return address
- a pointer to the stack address
With all this stowed away, arch_prepare_kretprobe() then sets the return
address for the targeted function to a special trampoline function called
kretprobe_trampoline() implemented in arch/x86_64/kernel/kprobes.c
* The kprobe completes as normal, with control passing back to the target
function that executes as normal, and eventually returns to our trampoline
function.
* Since a kprobe was installed on kretprobe_trampoline() during system
initialization, control passes back to kprobes via the architecture
specific function trampoline_probe_handler() which will lookup the
instance in an hlist maintained by kernel/kprobes.c, and then call
the handler function.
* When trampoline_probe_handler() is done, the kprobes infrastructure
single steps the original instruction (in this case just a top), and
then calls trampoline_post_handler(). trampoline_post_handler() then
looks up the instance again, puts the instance back on the free list,
and then makes a long jump back to the original return instruction.
So to recap, to instrument the exit path of a function this implementation
will cause four interruptions:
- A breakpoint at the very beginning of the function allowing us to
switch out the return address
- A single step interruption to execute the original instruction that
we replaced with the break instruction (normal kprobe flow)
- A breakpoint in the trampoline function where our instrumented function
returned to
- A single step interruption to execute the original instruction that
we replaced with the break instruction (normal kprobe flow)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make use of the user_mode macro where it's possible. This is useful for Xen
because it will need only to redefine only the macro to a hypervisor call.
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add 2 macros to set and get debugreg on x86_64. This is useful for Xen
because it will need only to redefine each macro to a hypervisor call.
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I suggest to change the way IRQs are handed out to PCI devices.
Currently, each I/O APIC pin gets associated with an IRQ, no matter if the
pin is used or not. It is expected that each pin can potentually be
engaged by a device inserted into the corresponding PCI slot. However,
this imposes severe limitation on systems that have designs that employ
many I/O APICs, only utilizing couple lines of each, such as P64H2 chipset.
It is used in ES7000, and currently, there is no way to boot the system
with more that 9 I/O APICs.
The simple change below allows to boot a system with say 64 (or more) I/O
APICs, each providing 1 slot, which otherwise impossible because of the IRQ
gaps created for unused lines on each I/O APIC. It does not resolve the
problem with number of devices that exceeds number of possible IRQs, but
eases up a tension for IRQs on any large system with potentually large
number of devices.
I only implemented this for the ACPI boot, since if the system is this big
and using newer chipsets it is probably (better be!) an ACPI based system
:). The change is completely "mechanical" and does not alter any internal
structures or interrupt model/implementation. The patch works for both
i386 and x86_64 archs. It works with MSIs just fine, and should not
intervene with implementations like shared vectors, when they get worked
out and incorporated.
To illustrate, below is the interrupt distribution for 2-cell ES7000 with
20 I/O APICs, and an Ethernet card in the last slot, which should be eth1
and which was not configured because its IRQ exceeded allowable number (it
actially turned out huge - 480!):
zorro-tb2:~ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
0: 65716 30012 30007 30002 30009 30010 30010 30010 IO-APIC-edge timer
4: 373 0 725 280 0 0 0 0 IO-APIC-edge serial
8: 0 0 0 0 0 0 0 0 IO-APIC-edge rtc
9: 0 0 0 0 0 0 0 0 IO-APIC-level acpi
14: 39 3 0 0 0 0 0 0 IO-APIC-edge ide0
16: 108 13 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb1
18: 0 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb3
19: 15 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb2
23: 3 0 0 0 0 0 0 0 IO-APIC-level ehci_hcd:usb4
96: 4240 397 18 0 0 0 0 0 IO-APIC-level aic7xxx
97: 15 0 0 0 0 0 0 0 IO-APIC-level aic7xxx
192: 847 0 0 0 0 0 0 0 IO-APIC-level eth0
NMI: 0 0 0 0 0 0 0 0
LOC: 273423 274528 272829 274228 274092 273761 273827 273694
ERR: 7
MIS: 0
Even though the system doesn't have that many devices, some don't get
enabled only because of IRQ numbering model.
This is the IRQ picture after the patch was applied:
zorro-tb2:~ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
0: 44169 10004 10004 10001 10004 10003 10004 6135 IO-APIC-edge timer
4: 345 0 0 0 0 244 0 0 IO-APIC-edge serial
8: 0 0 0 0 0 0 0 0 IO-APIC-edge rtc
9: 0 0 0 0 0 0 0 0 IO-APIC-level acpi
14: 39 0 3 0 0 0 0 0 IO-APIC-edge ide0
17: 4425 0 9 0 0 0 0 0 IO-APIC-level aic7xxx
18: 15 0 0 0 0 0 0 0 IO-APIC-level aic7xxx, uhci_hcd:usb3
21: 231 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb1
22: 26 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb2
23: 3 0 0 0 0 0 0 0 IO-APIC-level ehci_hcd:usb4
24: 348 0 0 0 0 0 0 0 IO-APIC-level eth0
25: 6 192 0 0 0 0 0 0 IO-APIC-level eth1
NMI: 0 0 0 0 0 0 0 0
LOC: 107981 107636 108899 108698 108489 108326 108331 108254
ERR: 7
MIS: 0
Not only we see the card in the last I/O APIC, but we are not even close to
using up available IRQs, since we didn't waste any.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the x86_64 version of the signal fix I just posted for i386.
This problem was first noticed on PPC and has already been fixed there.
But the exact same issue applies to other platforms in the same way. The
signal blocking for sa_mask and the handled signal takes place after the
handler setup. When the stack is bogus, the handler setup forces a
SIGSEGV. But then this will be blocked, and returning to user mode will
fault again and iterate. This patch fixes the problem by checking whether
signal handler setup failed, and not doing the signal-blocking if so. This
copies what was done in the ppc code. I think all architectures' signal
handler setup code follows this pattern and needs the change.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the x86-64 HPET code assumes the entire HPET implementation from
the spec is present. This breaks on boxes that do not implement the
optional legacy timer replacement functionality portion of the spec.
This patch fixes this issue, allowing x86-64 systems that cannot use the
HPET for the timer interrupt and RTC to still use the HPET as a time
source. I've tested this patch on a system systems without HPET, with HPET
but without legacy timer replacement, as well as HPET with legacy timer
replacement.
This version adds a minor check to cap the HPET counter value in
gettimeoffset_hpet to avoid possible time inconsistencies. Please ignore
the A2 version I sent to you earlier.
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow early printk code to take advantage of the full size of the screen, not
just the first 25 lines.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define pcibus_to_node to be able to figure out which NUMA node contains a
given PCI device. This defines pcibus_to_node(bus) in
include/linux/topology.h and adjusts the macros for i386 and x86_64 that
already provided a way to determine the cpumask of a pci device.
x86_64 was changed to not build an array of cpumasks anymore. Instead an
array of nodes is build which can be used to generate the cpumask via
node_to_cpumask.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds in the necessary support for sparsemem such that x86-64
kernels may use sparsemem as an alternative to discontigmem for NUMA
kernels. Note that this does no preclude one from continuing to build NUMA
kernels using discontigmem, but merely allows the option to build NUMA
kernels with sparsemem.
Interestingly, the use of sparsemem in lieu of discontigmem in NUMA kernels
results in reduced text size for otherwise equivalent kernels as shown in
the example builds below:
text data bss dec hex filename
2371036 765884 1237108 4374028 42be0c vmlinux.discontig
2366549 776484 1302772 4445805 43d66d vmlinux.sparse
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to use the alternative sparsemem implmentation for NUMA kernels,
we need to reorganize the config options. This patch effectively abstracts
out the CONFIG_DISCONTIGMEM options to CONFIG_NUMA in most cases. Thus,
the discontigmem implementation may be employed as always, but the
sparsemem implementation may be used alternatively.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch pulls out all remaining direct references to contig_page_data
from arch/x86-64, thus saving an ifdef in one case.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ingo recently introduced a great speedup for allocating new mmaps using the
free_area_cache pointer which boosts the specweb SSL benchmark by 4-5% and
causes huge performance increases in thread creation.
The downside of this patch is that it does lead to fragmentation in the
mmap-ed areas (visible via /proc/self/maps), such that some applications
that work fine under 2.4 kernels quickly run out of memory on any 2.6
kernel.
The problem is twofold:
1) the free_area_cache is used to continue a search for memory where
the last search ended. Before the change new areas were always
searched from the base address on.
So now new small areas are cluttering holes of all sizes
throughout the whole mmap-able region whereas before small holes
tended to close holes near the base leaving holes far from the base
large and available for larger requests.
2) the free_area_cache also is set to the location of the last
munmap-ed area so in scenarios where we allocate e.g. five regions of
1K each, then free regions 4 2 3 in this order the next request for 1K
will be placed in the position of the old region 3, whereas before we
appended it to the still active region 1, placing it at the location
of the old region 2. Before we had 1 free region of 2K, now we only
get two free regions of 1K -> fragmentation.
The patch addresses thes issues by introducing yet another cache descriptor
cached_hole_size that contains the largest known hole size below the
current free_area_cache. If a new request comes in the size is compared
against the cached_hole_size and if the request can be filled with a hole
below free_area_cache the search is started from the base instead.
The results look promising: Whereas 2.6.12-rc4 fragments quickly and my
(earlier posted) leakme.c test program terminates after 50000+ iterations
with 96 distinct and fragmented maps in /proc/self/maps it performs nicely
(as expected) with thread creation, Ingo's test_str02 with 20000 threads
requires 0.7s system time.
Taking out Ingo's patch (un-patch available per request) by basically
deleting all mentions of free_area_cache from the kernel and starting the
search for new memory always at the respective bases we observe: leakme
terminates successfully with 11 distinctive hardly fragmented areas in
/proc/self/maps but thread creating is gringdingly slow: 30+s(!) system
time for Ingo's test_str02 with 20000 threads.
Now - drumroll ;-) the appended patch works fine with leakme: it ends with
only 7 distinct areas in /proc/self/maps and also thread creation seems
sufficiently fast with 0.71s for 20000 threads.
Signed-off-by: Wolfgang Wander <wwc@rentec.com>
Credit-to: "Richard Purdie" <rpurdie@rpsys.net>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu> (partly)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch will setup compatibility mode TASK_SIZE properly. This will
fix atleast three known bugs that can be encountered while running
compatibility mode apps.
a) A malicious 32bit app can have an elf section at 0xffffe000. During
exec of this app, we will have a memory leak as insert_vm_struct() is
not checking for return value in syscall32_setup_pages() and thus not
freeing the vma allocated for the vsyscall page. And instead of exec
failing (as it has addresses > TASK_SIZE), we were allowing it to
succeed previously.
b) With a 32bit app, hugetlb_get_unmapped_area/arch_get_unmapped_area
may return addresses beyond 32bits, ultimately causing corruption
because of wrap-around and resulting in SEGFAULT, instead of returning
ENOMEM.
c) 32bit app doing this below mmap will now fail.
mmap((void *)(0xFFFFE000UL), 0x10000UL, PROT_READ|PROT_WRITE,
MAP_FIXED|MAP_PRIVATE|MAP_ANON, 0, 0);
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Bligh determined that this patch is causing his test box to not boot.
Revert.
Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This works around the too fast timer seen on some ATI boards.
I don't feel confident enough about it yet to enable it by default, but give
users the option.
Patch and debugging from Christopher Allen Wing <wingc@engin.umich.edu>, with
minor tweaks (renamed the option and documented it)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The test case at
http://cvs.sourceforge.net/viewcvs.py/posixtest/posixtestsuite/conforman
ce/interfaces/clock_nanosleep/1-5.c fails if it runs as a 32bit process on
x86_86 machines.
The root cause is the sub 32bit process fails to restart the syscall after it
is interrupted by a signal.
The syscall number of sys_restart_syscall in table sys_call_table is
__NR_restart_syscall (219) while it's __NR_ia32_restart_syscall
(0) in ia32_sys_call_table. When regs->rax==(unsigned
long)-ERESTART_RESTARTBLOCK, function do_signal doesn't distinguish if
the process is 64bit or 32bit, and always sets restart syscall number
as __NR_restart_syscall (219).
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was a "off by one quad word" error in there. I don't think it is
exploitable because it will only store into a unused area, but better to plug
it.
Found and fixed by John Blackwood
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove duplicated ifdef
- Make core_id match what Intel uses
- Initialize phys_proc_id correctly for non DC case
- Handle non power of two core numbers.
Fixes for both i386 and x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the assumption that LAPIC entries contain the BSP as its
first entry. This is a slight improvement to the temporary fix submitted by
Suresh Siddha.
- Removes assumption that LAPIC entries contain BSP first.
- Builds x86_acpiid_to_apicid[] and bios_cpu_apicid[] properly with BSP as
first entry.
- Made maxcpus=1 boot on these systems. Since the parsing earlier in
arch/x86_64/kernel/mpparse.c stopped after maxcpus entries, other entries
were not processed, this causes kernel not to boot on these systems.
TBD: x86_acpiid_to_apicid and bios_cpu_apicid[] seem to be exactly the
same. This could be removed, but might need more work to cleanup.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collected NMI watchdog fixes.
- Fix call of check_nmi_watchdog
- Remove earlier move of check_nmi_watchdog to later. It does not fix the
race it was supposed to fix fully.
- Remove unused P6 definitions
- Add support for performance counter based watchdog on P4 systems.
This allows to run it only once per second, which saves some CPU time.
Previously it would run at 1000Hz, which was too much.
Code ported from i386
Make this the default on Intel systems.
- Use check_nmi_watchdog with local APIC based nmi
- Fix race in touch_nmi_watchdog
- Fix bug that caused incorrect performance counters to be programmed in a
few cases on K8.
- Remove useless check for local APIC
- Use local_t and per_cpu variables for per CPU data.
- Keep other CPUs busy during check_nmi_watchdog to make sure they really
tick when in lapic mode.
- Only check CPUs that are actually online.
- Various other fixes.
- Fix fallback path when MSRs are unimplemented
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
