This replaces the binding for flash chips in booting-without-of.txt
with an clarified and improved version. It also makes
drivers/mtd/maps/physmap_of.c recognize this new binding. Finally it
revises the Ebony device tree source to use the new binding as an
example.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device tree source file for the PPC405 Walnut evaluation board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The patch below removes the dtc incantation instructions from the
in-kernel DTS files. It's not needed, and is prone to being
out-of-date most of the time.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch contains a handful of small fixes to allow the Ebony's
flash to be exposed as MTD devices via the physmap_of driver.
Specifically it:
- Makes a small addition to the device tree and zImage wrapper
to record the correct address for the flash in the device tree based
on the board switches as reported via an FPGA register.
- Prohibits building the old hard-coded "Ebony" flash map on
arch/powerpc kernels, in favour of using physmap_of's device tree
based approach.
- Enables MTD and physmap_of in the Ebony defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix mpc7448hpc2 tsi108 device_type bug.
Wrong device type will break the board startup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 8548 CDS PCI express controller node and PCI-X device node. The current
dts file is suitable for 8548 Rev 2.0 board with Arcadia 3.1.
This kind of board combination is the most popular.
Used the following compatible properties:
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The TSEC/eTSEC automatically detect their PHY interface type, unless
the type is RGMII-ID (RGMII with internal delay). In that situation,
it just detects RGMII. In order to fix this, we need to pass in rgmii-id
if that is the connection type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Removed explicit linux,phandle usage. Using references and labels now in PQ
and PQ2 boards currently supported in arch/powerpc.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds support for PowerQuicc on-chip PCMCIA. The driver is implemented as
of_device, so only arch/powerpc stuff is capable to use it, which now implies
only mpc885ads reference board.
To cope with the code that should be hooked inside driver, but is really board
specific (like set_voltage), global structure mpc8xx_pcmcia_ops holds
necessary function pointers that are filled in the BSP code.
[akpm@linux-foundation.org: whitespace diddles]
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PHY is active-low on the MPC85xx CDS and the 8560 ADS just had
the wrong sense for the internal PCI and CPM interrupts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the interrupt numbers match the OpenPIC spec intead of the
Freescale docs which distinguish between internal and external interrupts.
Now we can use the interrupt number directly to find the register offset
associated with it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the 83xx, 85xx, and 86xx device trees, add a "local-mac-address" property
to every Ethernet node that didn't have one. Add a comment indicating that
the "address" and/or "mac-address" properties are deprecated in DTS files
and will be removed at a later time. Change all MAC address properties to
have a zero MAC address value.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Begin with MPC8548 a new reset control register is added that asserts
HRESET_REQ to board logic.
This register is used for chip reset.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds device nodes for the PCI bridges as well as the ISA devices on
the newer revision MPC8641HPCN. It also adds the PCI ranges to the soc
node so that address translation for the ISA devices works properly.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifying 'console=ttyMM0' on the cmdline for the prmpc2800 is no
longer necessary.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes some problems with the way the some things
represented in the device tree for the Holly and Taiga boards. This
means changes both to the dts files, and to the code which
instantiates the tsi108 ethernet platform devices based on the device
tree.
- First, and most importantly, the ethernet PHYs are given
with an identical 'reg' property. This reg currently encodes the
accessible register used to initiate mdio interaction with the PHYs,
rather than a meaningful address on the parent bus (mdio in this
case), which is incorrect. Instead we give the address of these
registers as 'reg' in the mdio node itself, and encode the ID of each
phy in their 'reg' propertyies.
- Currently the platform device constructor enables a
workaround in the tsi108 ethernet driver based on the compatible
property of the PHY. This is incorrect, because the workaround in
question is necessary due to the board's wiring of the PHY, not the
model of PHY itself. This patch alters the constructor to instead
enable the workaround based on a new special property in the PHY node.
- The compatible properties on a number of nodes in the device
tree are insufficiently precise. In particular the PHYs give only
"bcm54xx", which is broken, since there are many bcm54xx PHY models,
and they have differences which matter. The mdio had a compatible
property of "tsi-ethernet" identical to the ethernet MAC nodes, which
doesn't make sense. The ethernet, i2c, bridge and PCI nodes were
given only as "tsi-*" which is somewhat inprecise, we replace with
"tsi108-*" in the case of Taiga (which has a TSI108 bridge), and
"tsi109-*", "tsi108-*" in the case of Holly (which has a TSI109
bridge).
- We remove some "model" properties from the ethernets on
Taiga board which were neither useful nor adequately precise.
- On Holly we change to using a dtc label instead of a full
path to reference the MPIC node, which makes the dts a little more
readable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the Holly device tree includes a bootargs property in
/chosen, which gives a commandline. This is somewhat inconvenient,
because it means an alternative default command line can't be given in
the kernel config - the value obtained from the dts via the
bootwrapper will always override CONFIG_CMDLINE.
This removes the command line from the dts, and instead puts the
same command line as a default in holly_defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the device tree for Ebony, the 'ranges' property in the node for
the EBC bridge shows the mappings from the chip select / address lines
actually used for the EBC peripherals into the address space of the
OPB. At present, these mappings are hardcoded in ebony.dts for the
mappings set up by the OpenBIOS firmware when it configures the EBC
bridge.
This replaces the hardcoded mappings with code in the zImage to
read the EBC configuration registers and create an appropriate ranges
property based on them. This should make the zImage and kernel more
robust to changes in firmware configuration. In particular, some of
the Ebony's DIP switches can change the effective address of the Flash
and other peripherals in OPB space. With this patch, the kernel will
be able to cope with at least some of the possible variations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Unbreak lite5200 dts, which were broken by
5c1992f833
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch corrects a number of minor errors in the Ebony device tree:
- Missing (given as 0) cache sizes are added to the CPU node
- device_type properties are removed from nodes which don't
have a reasonably well defined device_type binding. This does require
a very small code change to locate the busses to be probed for
of_platform devices by 'compatible' instead of 'device_type'.
- A node is added for the SRAM controller
- The unit address of the small-flash node is adjusted to
correctly reflect the reg property.
- device_type values for the MAL and ZMII are updated to
reflected more up-to-date versions of the binding.
- An incorrect offset in the partition map for the large-flash
node is corrected.
- Some redundant values, already commented out are removed
entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove explicit phandles and move to using references that autogenerate the
phandles when needed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding memory-controller and l2-cache-controller entries to be used by EDAC
as of_devices for MPC8541 CDS, MPC8544 DS, MPC8555 CDS, and MPC8568 MDS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding memory-controller and l2-cache-controller entries to be used by EDAC
as of_devices for MPC8540 ADS, MPC8548 CDS, and MPC8560 ADS.
Also fixed up the size of the PCI node on MPC8560 ADS.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MPC834x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC832x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a device tree for the Ebony evaluation board (440GP based). This
tree is not complete or finalized. This tree needs a version of dtc
recent enough to include reference-to-labels to process.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
