Just adds GPS support found in R2H thanks to Sam Lin. It will
make a "gps" file in /sys/devices/platform/asus-laptop/.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
We need to handle all events, because some dsdt use events >= 0x80
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
cpm_uart_init_portdesc is referenced from non-init code and thus we were
getting the following warning:
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:cpm_uart_init_portdesc from .text between 'cpm_uart_init' (at offset 0x18020) and 'cpm_uart_drv_remove'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC834x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC832x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The rheap allocation functions return a pointer, but the actual value is based
on how the heap was initialized, and so it can be anything, e.g. an offset
into a buffer. A ulong is a better representation of the value returned by
the allocation functions.
This patch changes all of the relevant rheap functions to use a unsigned long
integers instead of a pointer. In case of an error, the value returned is
a negative error code that has been cast to an unsigned long. The caller can
use the IS_ERR_VALUE() macro to check for this.
All code which calls the rheap functions is updated accordingly. Macros
IS_MURAM_ERR() and IS_DPERR(), have been deleted in favor of IS_ERR_VALUE().
Also added error checking to rh_attach_region().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
HD interface and AC97 interface share some pins and they are enabled at
the same time, In order to use AC97 interface, we need to disable the HD
interface first.
Signed-off-by:Jason Jin<jason.jin@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch moves a copy of reg_booke.h to include/asm-powerpc and fixes
up the ifdef protection.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
HP nx6125/nx6325/... machines have a _GPE handler with an infinite
loop sending Notify() events to different ACPI subsystems.
Notify handler in ACPI driver is a C-routine, which may call ACPI
interpreter again to get access to some ACPI variables
(acpi_evaluate_xxx).
On these HP machines such an evaluation changes state of some variable
and lets the loop above break.
In the current ACPI implementation Notify requests are being deferred
to the same kacpid workqueue on which the above GPE handler with
infinite loop is executing. Thus we have a deadlock -- loop will
continue to spin, sending notify events, and at the same time
preventing these notify events from being run on a workqueue. All
notify events are deferred, thus we see increase in memory consumption
noticed by author of the thread. Also as GPE handling is bloked,
machines overheat. Eventually by external poll of the same
acpi_evaluate, kacpid is released and all the queued notify events are
free to run, thus 100% cpu utilization by kacpid for several seconds
or more.
To prevent all these horrors it's needed to not put notify events to
kacpid workqueue by either executing them immediately or putting them
on some other thread. It's dangerous to execute notify events in
place, as it will put several ACPI interpreter stacks on top of each
other (at least 4 in case of nx6125), thus causing kernel stack
overflow.
First attempt to create a new thread was done by Peter Wainwright
He created a bunch of threads, which were stealing work from a kacpid
workqueue.
This patch appeared in 2.6.15 kernel shipped with Ubuntu 6.06 LTS.
Second attempt was done by me, I created a new thread for each Notify
event. This worked OK on HP nx machines, but broke Linus' Compaq
n620c, by producing threads with a speed what they stopped the machine
completely. Thus this patch was reverted from 18-rc2 as I remember.
I re-made the patch to create second workqueue just for notify events,
thus hopping it will not break Linus' machine. Patch was tested on the
same HP nx machines in #5534 and #7122, but I did not received reply
from Linus on a test patch sent to him.
Patch went to 19-rc and was rejected with much fanfare again.
There was 4th patch, which inserted schedule_timeout(1) into deferred
execution of kacpid, if we had any notify requests pending, but Linus
decided that it was too complex (involved either changes to workqueue
to see if it's empty or atomic inc/dec).
Now you see last variant which adds yield() to every GPE execution.
http://bugzilla.kernel.org/show_bug.cgi?id=5534http://bugzilla.kernel.org/show_bug.cgi?id=8385
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit c0d127b569.
These changes to AML locking were made to allow
Notify handlers to be called on the stack
and not deadlock. However, that scheme turns
out to be flawed and was reverted by the previous commit,
so this commit restores the locking to it previous design.
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit a8f4af6dc6.
Thus restoring ACPICA's new acpi_serialize code.
This commit by itself may cause a regression, but
it is reverted in this order so that subsequent
reverts reverts under this one can be made
without conflict.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
IB: Put rlimit accounting struct in struct ib_umem
IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules
This reverts commit 5b479c91da.
Quoth Neil Brown:
"It causes an oops when auto-detecting raid arrays, and it doesn't
seem easy to fix.
The array may not be 'open' when do_md_run is called, so
bdev->bd_disk might be NULL, so bd_set_size can oops.
This whole approach of opening an md device before it has been
assembled just seems to get more and more painful. I think I'm going
to have to come up with something clever to provide both backward
comparability with usage expectation, and sane integration into the
rest of the kernel."
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer. Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Looks like you removed the combined_mode quirk (yay!) but didn't update
kernel-parameters.txt... might confuse people. Here's a patch to remove
mention of it from the documentation.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Warning(linux-2.6.21-git4//drivers/ata/libata-core.c:904): No description found for parameter 'new_sectors'
Warning(linux-2.6.21-git4//drivers/ata/libata-core.c:941): No description found for parameter 'new_sectors'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes some problems with ADMA-capable controllers with
regard to freeze, thaw and irq_clear libata callbacks. Freeze and
thaw didn't switch the ADMA-specific interrupts on or off, and more
critically the irq_clear function didn't respect the restriction that
the notifier clear registers for both ports have to be written at
the same time even when only one port is being cleared. This could
result in timeouts on one port when error handling (i.e. as a result
of hotplug) occurred on the other port.
As well, this fixes some issues in the interrupt handler: we shouldn't
check any ADMA status if the port has ADMA switched off because of
an ATAPI device, and it also checks to see if any ADMA interrupt has
been raised even when we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a known problem with sata_promise on SATAII-150/300 TX4
controller cards: it enumerates drives in an order that differs
from the port numbers printed on the controller cards. However,
Promise's BIOS and Linux driver both get the order right.
I investigated Promise's Linux driver (v1.01.0.23), and found
that it explicitly changes the mapping from logical port number
to ATA engine MMIO address on the SATAII TX4 cards. It does this
on all SATAII TX4 cards, without inspecting revision etc. The
SATAII TX2plus cards continue to use the same mapping that was
used for the first-generation chips.
This patch updates sata_promise to use the new port number to
ATA engine mapping on SATAII TX4 cards, which fixes the drive
enumeration order problem on those cards. Tested on several
1st and 2nd generation TX2plus and TX4 chips.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_promise error decode update changed pdc_host_intr()
to return and not complete the qc after detecting an error.
Unfortunately not completing the qc:s causes them to always
time out on error, which is wrong and has nasty side-effects.
This patch updates pdc_error_intr() to call ata_port_abort(),
similar to ahci and sata_sil24. Doing this is important as it
makes EH see the original error and not a bogus timeout.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
_GTF command is never ATA_PROT_ATAPI_NODATA whether the device is
ATAPI or not. It's always ATA_PROT_NODATA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Copied from b44 driver, but it works:
netconsole: device eth0 not up yet, forcing it
atl1: eth0 link is up 100 Mbps full duplex
netconsole: network logging started
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ejecting a PCMCIA IBM Token Ring card that has not had its dev->open()
called will reliably trigger an uninitialized spinlock oops when
spinlock debugging is enabled. The system then hangs, occasionally
softlockup oopsing. Apparently ibmtr.c:tok_interrupt() doesn't expect
to be called before tok_open(), but tok_interrupt() gets called anyway
when the card is ejected. So, set an already-existing flag which
causes tok_interrupt() to bail out early upon card ejection. Tested by
inserting and removing the PCMCIA card several times.
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By default, the skge driver now enables wake on magic and wake on PHY.
This is a bad default (bug), wake on PHY means machine will never shutdown
if connected to a switch.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>a
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: fix PIO setup on resume for ATAPI devices
ide: legacy PCI bus order probing fixes
ide: add ide_proc_register_port()
ide: add "initializing" argument to ide_register_hw()
ide: cable detection fixes (take 2)
ide: move IDE settings handling to ide-proc.c
ide: split off ioctl handling from IDE settings (v2)
ide: make /proc/ide/ optional
ide: add ide_tune_dma() helper
ide: rework the code for selecting the best DMA transfer mode (v3)
ide: fix UDMA/MWDMA/SWDMA masks (v3)
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFS: Kill the obsolete NFS_PARANOIA
NFS: use __set_current_state()
sunrpc: fix crash in rpc_malloc()
NFS: Clean up NFSv4 XDR error message
NFS: NFS client underestimates how large an NFSv4 SETATTR reply can be
SUNRPC: Fix pointer arithmetic bug recently introduced in rpc_malloc/free
NFS: Remove redundant check in nfs_check_verifier()
NFS: Fix a jiffie wraparound issue
IDE PCI host drivers should register themselves with IDE core only when
IDE driver is built-in, otherwise (IDE driver is modular and thus IDE PCI
host drivers are also modular) the code has no effect and just complicates
the probing.
Fix it by adding new config option CONFIG_IDEPCI_PCIBUS (defined only when
needed and invisible to the user) and covering by #ifdef/#endif the code
in question. It turned out that "ide=reverse" was silently accepted but did
nothing in case when IDE driver was modular, this is fixed now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* create_proc_ide_interfaces() tries to add /proc entries for every probed
and initialized IDE port, replace it by ide_proc_register_port() which does
it only for the given port (also rename destroy_proc_ide_interface() to
ide_proc_unregister_port() for consistency)
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions
* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them
* there is now no need to add /proc entries for IDE ports in proc_ide_create()
so don't do it
* proc_ide_create() needs now to be called before drivers are probed - fix it,
while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "initializing" argument to ide_register_hw() and use it instead of ide.c
wide variable of the same name. Update all users of ide_register_hw()
accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...
* print user-friendly warning about limiting the maximum transfer speed
to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
also while at it cleanup eighty_ninty_three() a bit
* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
- bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
(please see FIXME comment in eighty_ninty_three() for more details)
- CONFIG_IDEDMA_IVB=y/n cases were interchanged
- check for SATA devices was missing
* remove private cable warnings from pdc_202xx{old,new} drivers now that core
code provides this functionality (plus, in pdc202xx_new case the test could
give false warnings for ATAPI devices because pdc202xx_new driver doesn't
even support ATAPI DMA)
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
