The timberdale FPGA is found on the Intel in-Vehicle Infotainment reference board
russelville.
The driver is a PCI driver which chunks up the I/O memory and distributes interrupts
to a number of platform devices for each IP inside the FPGA.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This works around issues with allmodconfig where it won't propagate the
dependency from the WM831x core back to the I2C and MFD cores. When
doing allmodconfig this causes WM831x to be omitted and ensures that in
normal builds the dependencies get shaken out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq infrastructure functions aren't currently exported,
preventing modular builds.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This remove the default 'y' selection of AB4500, currently everyone
enabling the SPI subsystem will get a copy of this driver.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM8607 depends on I2C and MFD_CORE. Since 88PM8607 is built-in
kernel, it also requires that I2C and MFD_CORE are built-in
kernel also.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8320 is an integrated power management subsystem providing
voltage regulators, RTC, watchdog and other functionality. The
WM8320 is derived from the WM831x and therefore shares most of
the driver code with the WM831x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds core driver support for AB4500 mixed signal
multimedia & power management chip. This connects to U8500
on the SSP (pl022) and exports read/write functions for
the device to get access to this chip. This also registers
the client devices and sets the parent.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Reviewed-by: Mark Brown <broonie@sirena.org.uk>
Reviewed-by: Jean-Christophe <plagnioj@jcrosoft.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for 88PM8607 found in Marvell DKB development
platform. This driver is a proxy for all accesses to 88PM8607
sub-drivers which will be merged on top of this one, RTC, regulators,
battery and so on.
This chip is manufactured by Marvell.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
This patch adds an MFD driver for the SuperH Mobile SDHI
hardware block. At this point the driver simply wraps the
tmio-mmc driver with some clock code. In the future this
driver is the place to put SDHI specific hotplug code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TWL4030/5030 family of multifunction devices allows board-specific
control of the the various regulators, clock and reset lines through
'scripts' that are loaded into its memory. This allows for Dynamic Power
Switching (DPS).
Implement board-independent core support for DPS that is then used by
board-specific code to load custom DPS scripts.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the ability to read out OTP (One-Time Programmable)
registers in the AB3100 MFD ASIC. It's a simple sysfs file you
can cat to prompt. The OTP registers of the AB3100 are used to
store various device-unique information such as customer ID,
product flags and the 3GPP standard IMEI (International Mobile
Equipment Indentity) number.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides the core Freescale MC13783 support. It
registers the client platform_devices and provides access
to the A/D converter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables the ASIC3's DS1WM MFD cell, supported by the ds1wm driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.
It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.
This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes htc-pasic3 register the DS1WM and LED cell drivers
through the MFD core infrastructure instead of allocating the platform
devices manually. It also calculates the bus_shift parameter from the
memory resource size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
What the PCF05633 calls as a 'GPIO' is much more than the GPIO in the linux
sense and there are only 4 of them - which means, the gpiolib is not used
here.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds basic support for the PCF50633 ADC. The subtractive mode
is not supported yet.
Since we don't have adc subsystem, it currently lives in drivers/mfd.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Acked-by: Jonathan Cameron <jonathan.cameron@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch implements the core of the PCF50633 driver. This core driver has
generic register read/write functions and does interrupt management for its
sub devices.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
ove the menelaus driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.
One way to think of these chips are as the PMIC family most
used with OMAP2 generation chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Move the tps65010 driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.
One way to think of these chips are as the PMIC family most
used with OMAP1 generation chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Basic MFD framework for the MSP430 microcontroller firmware used
on the dm355evm board:
- Provides an interface for other drivers: register read/write
utilities, and register declarations.
- Directly exports:
* Many signals through the GPIO framework
+ LEDs
+ SW6 through gpio sysfs
+ NTSC/nPAL jumper through gpio sysfs
+ ... more could be added later, e.g. MMC signals
* Child devices:
+ LEDs, via leds-gpio child (and default triggers)
+ RTC, via rtc-dm355evm child device
+ Buttons and IR control, via dm355evm_keys
- Supports power-off system call. Use the reset button to power
the board back up; the power supply LED will be on, but the
MSP430 waits to re-activate the regulators.
- On probe() this:
* Announces firmware revision
* Turns off the banked LEDs
* Exports the resources noted above
* Hooks the power-off support
* Muxes tvp5146 -or- imager for video input
Unless the new tvp514x driver (tracked for mainline) is configured,
this assumes that some custom imager driver handles video-in.
This completely ignores the registers reporting the output voltages
on the various power supplies. Someone could add a hwmon interface
if that seems useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Register a child device for the codec in the WM8400.
Also switch the unregistration of the MFD devices to use the MFD core
since the current code is hand rolling the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Finish removing dependency of TWL driver stack on platform-specific
IRQ definitions ... and remove the build dependency on OMAP.
This lets the TWL4030 code be included in test builds for most
platforms, and will make it easier for non-OMAP folk to update
most of this code for new APIs etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Otherwise we could build in WM8400 but not I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
ia64 allmodconfig:
In file included from include/linux/ucb1400.h:27,
from drivers/mfd/ucb1400_core.c:24:
include/asm-generic/gpio.h: In function `gpio_get_value_cansleep':
include/asm-generic/gpio.h:147: error: implicit declaration of function `gpio_get_value'
include/asm-generic/gpio.h: In function `gpio_set_value_cansleep':
include/asm-generic/gpio.h:153: error: implicit declaration of function `gpio_set_value'
drivers/mfd/ucb1400_core.c: At top level:
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch adds the core of the TWL4030 driver, which supports
chips including the TPS65950. These chips are multi-function; see
http://focus.ti.com/docs/prod/folders/print/tps65950.html
Public specs are in the works. For now, the block diagram on
the second page of the datasheet is fairly informative.
There are some known issues with this core code. Most notably,
the IRQ dispatching needs simplification (to use more of genirq),
generalization (integrating support for secondary IRQ dispatch
as well as primary, and removing the build dependency on OMAP),
and then probably updating to leverage threaded IRQ support
(expected to arrive in mainline "soon").
Once the core is in mainline, drivers for other parts of this
chip can follow its lead and start swimming upstream too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Implement the I2C control interface for the WM8350. This code was
originally written by Liam Girdwood and has been updated for submission
by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 is an integrated audio and power management subsystem
intended for use as the primary PMIC in mobile multimedia applications.
The WM8350 can be controlled via either I2C or SPI - the control
interface is provided by a separate module in order to allow greatest
flexibility in configuring the kernel.
This driver was originally written by Liam Girdwood and has since been
updated to current kernel APIs and split up for submission by me. All
the heavy lifting here was done by Liam.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 is a highly integrated audio CODEC and power management unit
optimised for use in mobile multimedia applications. This patch adds
core support for the WM8400 to the MFD subsystem.
Both I2C and SPI access are supported by the hardware but currently only
I2C access is implemented. The code is structured to allow SPI support
to be slotted in later.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
This patch splits ucb1400_ts into ucb1400_ts and ucb1400_core.
Since this chip supports more features than only touchscreen,
it was necessary to prepare it for feature addition. The
previous functionality is preserved by applying this patch.
[Build fixes for non-ARM by Stephen Rothwell and Takashi Iwai]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the TC6387XB. Unlike other TMIO devices this one
has only one subdevice and no interrupt mux, however using the MFD framework
allows it to share the TMIO MMC driver.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patchset provides support for the core functinality of the T7L66XB
SoC from Toshiba. Supported in this patchset is the IRQ MUX, MMC controller
and NAND flash controller.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
