Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:
include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared
`static' but never defined
include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
`static' but never defined
by wiping out the whole "function prototyping" section from the header file
<asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
already dead in the IDE driver; move the only useful prototype into the driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Work around the CPU clock miscalculation on Au1000DA/HA/HB due the
sys_cpupll register being write-only, i.e. actually do what the comment
before cal_r4off() function advertised for years but the code failed at.
This is achieved by just giving user a chance to define the clock
explicitly in the board config. via CONFIG_SOC_AU1000_FREQUENCY option,
defaulting to 396 MHz if the option is not given...
The patch is based on the AMD's big unpublished patch, the issue seems to
be an undocumented errata (or feature :-)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Setup hwif->dev in au_ide_probe().
* Use hwif->dev instead of ahwif->dev in auide_build_sglist(),
auide_build_dmatable(), auide_dma_end() and auide_ddma_init().
* Remove no longer needed 'dev' field from _auide_hwif type.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by getting the PCI resources back into the 32-bit range -- there's no
need therefore for CONFIG_RESOURCES_64BIT either. This makes Alchemy PCI
work again while currently the kernel skips the bus scan.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the introduction of MIPS_CPU_IRQ_BASE, the hardcoded IRQ number of
the au1100/au1200 SD controller(s) is no longer valid.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do what the commits commits f3e8d1da38 and
9d360ab4a7 failed to achieve -- actually
convert the Alchemy code to irq_cpu.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the clock rate of the i8253 PIT. A MIPS system may not have
a PIT by the symbol is used all over the kernel including some APIs.
So keeping it defined to the number for the PIT is the only sane thing
for now.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was getting a little big, ugly and a primary source for merge conflicts.
Also the old method was a bit too forgiving in that the workaround did
default to off, so now there is an explicit #error forcing platform
maintainers to think if they should enable a workaround for a particular
platform.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This updates the DMA whitelist in MIPS specific au1xxx ide
driver to use NULL instead of "ALL" as the wildcard.
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Here is a driver for the Alchemy au1550 PSC (Programmable Serial
Controller) in SPI master mode.
It supports dma transfers using the Alchemy descriptor based dma controller
for 4-8 bits per word SPI transfers. For 9-24 bits per word transfers, pio
irq based mode is used to avoid setup of dma channels from scratch on each
number of bits per word change.
Tested with au1550; this may also work on other MIPS Alchemy cpus, like
au1200/au1210/au1250. Used extensively with SD card connected via SPI;
this handles 8.1MHz SPI clock transfers using dma without any problem (the
highest SPI clock freq possible with au1550 running on 324MHz).
The driver supports sharing of SPI bus by multiple devices. All features
of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per
word in 4-24 range).
As the SPI clock of the controller depends on main input clock that shall
be configured externally, platform data structure for au1550 SPI controller
driver contains mainclk_hz attribute to define the input clock rate. From
this value, dividers of the controller for SPI clock are set up for
required frequency.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Whitespace and section fixups. Remove partial workaround for platform
setup bug in dma_mask setup; it couldn't work with multiple controllers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the static prototypes from the au1xxx_ide.h, some of
them were not even implemented. Also, they caused build breakage since
they differed from the functions actually implemented in
drivers/ide/mips/au1xxx-ide.c.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The problem was introduced in 2.6.18.3 with the casting of some
36bit-defines (PCI memory) in au1000.h to resource_size_t which may be
u32 or u64 depending on the experimental CONFIG_RESOURCES_64BIT.
With unset CONFIG_RESOURCES_64BIT, the pci-memory cannot be accessed
because the ioremap in arch/mips/au1000/common/pci.c already used the
truncated addresses.
With set CONFIG_RESOURCES_64BIT, things get even worse, because PCI-scan
aborts, due to resource conflict: request_resource() in arch/mips/pci/pci.c
fails because the maximum iomem-address is 0xffffffff (32bit) but the
pci-memory-start-address is 0x440000000 (36bit).
To get pci working again, I propose the following patch:
1. remove the resource_size_t-casting from au1000.h again
2. make the casting in arch/mips/au1000/common/pci.c (it's allowed and
necessary here. The 36bit-handling will be done in __fixup_bigphys_addr).
With this patch pci works again like in 2.6.18.2, the gcc-compile warnings
in pci.c are gone and it doesn't depend on CONFIG_EXPERIMENTAL.
Signed-off-by: Alexander Bigga <ab@mycable.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/au1000/common/pci.o
arch/mips/au1000/common/pci.c:42: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:43: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:49: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:50: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c: In function ‘au1x_pci_setup’:
arch/mips/au1000/common/pci.c:82: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Au1xx IDE controller driver doesn't compile:
CC drivers/ide/mips/au1xxx-ide.o
/linux-2.6.19-rc6-work/drivers/ide/mips/au1xxx-ide.c:480: error: conflicting types for 'auide_ddma_tx_callback'
include2/asm/mach-au1x00/au1xxx_ide.h:174: error: previous declaration of 'auide_ddma_tx_callback' was here
/linux-2.6.19-rc6-work/drivers/ide/mips/au1xxx-ide.c:486: error: conflicting types for 'auide_ddma_rx_callback'
include2/asm/mach-au1x00/au1xxx_ide.h:176: error: previous declaration of 'auide_ddma_rx_callback' was here
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add missing PSC #define's required for the drivers using PSC on DBAu1550
board (also fixing Au1550 PSC3 address) and all Au1200-based boards as
well. Make the OSS driver use the correct PSC definitions fo each board.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD Au1200 SOC just doesn't have UART3, so KGDB won't even compile for it
as is, here's the fix to make KGDB use UART1.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
USB OpenHCI host controller on Au1550 only decodes memory addresses from
0x14020000 to 0x1407FFFF according to the databook, which gives 0x60000
(on the prior Au1x00 chips the map size was 1MB).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes here include removing all of CONFIG_PM while it is being repeatedly
smacked with a lead pipe, moving the BURSTMODE param to a #define (it should
be defined almost always anyway), fixing the rqsize stuff, pulling ide_ioreg_t,
and general cleanups and whatnot.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- converted to platform bus
- removed pci dependencies
- removed virt_to_phys/phys_to_virt calls
System now can root off of a disk.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/Documentation/mips/AU1xxx_IDE.README b/Documentation/mips/AU1xxx_IDE.README
new file mode 100644
* remove two already unused and commented structures
* added an ULL suffix to several address constants that use bits 35-32
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
