gActionOUIConnect1x1 is used to specify action OUIs for 1x1
connection.
Some Access Points are unable to handle SMPS and OMN frames and shows
abnormal behaviour when STA is switching between 2x2 to 1x1 and
vice-versa. To avoid this, restrict connection in 1x1 mode with such APs.
Here the scenario is DUT STA1 connects in 2x2 mode to AP1 in 5G mode then
later on DUT another STA2 iface connects to AP2 in 2G mode. DUT sends OMN
frame to AP1 to inform that it is going to switch to 1x1 mode. AP1 ack
this frame but doesn't change its Tx rates and continues to use 2x2 rates
which DUT cannot ACK. This causes low throughput issue where AP1 Tx rate
falls to 6Mbps due to missing acks.
Hence, 5G band capability bit in "gActionOUIConnect1x1" is set to make
connections in 1x1 with such AP.
Presently, 5G band capability bit is not checked if 2G band capability bit
is not set or 2G band is not enabled. Hence, Vendor AP capability check for
2G and 5G Band is refactored.
Change-Id: Ic6b682451405a2373000e4c64656f50c2fab0ee6
CRs-Fixed: 2558293
Add action_oui ini gActionOUIDisableAggressiveEDCA to identify peers for
which aggressive EDCA configuration causes some IOT issues.
Change-Id: Ifea0c224cef2378727c9f78d8b571ea9c57bb662
CRs-Fixed: 2507191
Few IOT APs advertise reduced NSS capabilities on ending
up in bad state. These APs can later recover to support
the actual NSS capabilities. In this scenario, when STA
initiates connection to these APs, which are in bad state,
reduced NSS capabilities is advertised. STA cannot later
upgrade NSS capabilities to the minimum of STA max NSS
capability and APs actual NSS capability, once AP recovers.
Fix is to advertise max NSS capability during connection
with these IOT APs based on vendor OUIs and downgrade if
AP still advertises reduced NSS capability in association
response.
Change-Id: I49ea13534b1a44fd9ffadd1e8fb44e9d782147c4
CRs-Fixed: 2453938
Add action_oui ini gActionOUIDisableAggressiveTX to identify peers for
which some of aggressive TX features are to be disabled in firmware,
when DUT is operating in softap mode.
Aggressive TX features disabled are SIFS bursting, assist and support of
more than 32 frames in AMPDU.
Change-Id: I89fb6d40be5110b0331e84ed3239cd997ce0c899
CRs-Fixed: 2364888
Add support for wildcard OUI 0xFFFFFF in action OUI framework.
When the OUI FFFFFF is defined for some action OUI ini and bit 0
of info_presence bit is set to 0 then the check for vendor OUI
in vendor specific IEs and the vendor IE data checks are skipped
and other checks like MAC, Capabilities are done during connection.
Change-Id: I6e996c5d79f4f7bd91e11134b1b8ba69a1ff0253
CRs-Fixed: 2293167
Add support for new 1x1 connect with 1 Tx/Rx Chain action OUI to be
parsed and sent to the FW. From host during connection, the behaviour
is same as existing connect 1x1 action OUI where nss is sent to 1 to
the FW, but the FW takes the decision to use only one Tx/Rx chain
based on the OUIs defined in the new action ID.
Change-Id: Ia464209043dc73bcc71577c43b28fbe13e780c23
CRs-Fixed: 2264326
Add support for action OUI extensions which can be used by station
to control mode of connection, connected AP's in-activity time and
Tx rate etc.,
Change-Id: Ie85e29c4b0ed7ac2815709d7a4e607c4ba46c6ca
CRs-Fixed: 2254502
