Support for the ITE8172 based boards was deleted a while ago so this is
dead code.
The Kconfig dependency on MIPS was wrong anyway, MIPS is a processor
architecture and nothing else; guesses on systems architecture are likely
to be wrong ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
I will not commit even trivial and obvious one-line fixes without building.
Only clever people can get away with that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ESB2ROM uses PCI interface functions.
With CONFIG_PCI=n:
drivers/mtd/maps/esb2rom.c: In function 'esb2rom_init_one':
drivers/mtd/maps/esb2rom.c:167: warning: implicit declaration of function 'pci_dev_get'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
inlined below is the patch that adds physmap driver for of_device.
It's an MTD part of the two-part support for flash/ROM devices based
on Open Firmware descriptions. The arch part (currently only PowerPC
which is no surprise) was introduced to powerpc folks earlier and
recently the older version of the powerpc part has been included into
the powerpc.git tree
(see http://www.kernel.org/git/?p=linux/kernel/git/paulus/powerpc.git;a=commitdiff;h=28f9ec349ae47c91768b7bc5607db4442c818e11).
drivers/mtd/maps/Kconfig | 9 +
drivers/mtd/maps/Makefile | 1
drivers/mtd/maps/physmap_of.c | 255 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 265 insertions(+)
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Sergey Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
RedBoot supports storing the FIS directory and the RedBoot
configuration area in the same block of flash memory. This is
not the most common RedBoot configuration, but it is used on
commercially available boards supported by the kernel.
A recent patch to mtd/redboot.c (http://lkml.org/lkml/2006/3/20/410)
which corrected the skipping of deleted table entries has exposed the
latent problem of the kernel redboot parser running off the end of the
FIS directory and interpreting the RedBoot configuration information
as table entries.
This patch terminates the table parsing when the first truly empty
entry is found (table entry deletion only clears the first byte of the
name, so two cleared bytes in a row indicates the end of the table),
thereby supporting the combined redboot FIS directory and RedBoot
configuration information flash layout scenario.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for 16-bit NAND bus-width for the AT91 NAND driver.
The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.
Orignal Patch from Patrice Vilchez
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Number of address bytes for 64-128 MiB NANDs is 4, not 5.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Select MTD_NAND_ECC_SMC (ECC byte order according to the Smart Media
Specification) if MTD_NAND_NDFC is used.
Using the wrong byte order causes fatal, unnoticed data damage.
For further information see:
http://lists.infradead.org/pipermail/linux-mtd/2006-November/016920.html
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Can't analyze FIS directory in CYGSEM_REDBOOT_FLASH_COMBINED_FIS_AND_CONFIG
really.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch fixes the
"jffs2_flash_writev(): Non-contiguous write to 00825300 with mtd_dataflash" bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
The newly-added cafe_ecc.c had a lot of it because of the way the lookup
table was auto-generated; clean up the other files too while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
While we're fixing up the newly-added symbol, change the neighbouring ones
too, for consistency and also to reflect the author's interpretation of
the GPL -- which is that _no_ non-GPL modules are permitted. The author
always intended his code to be released under the GPL, and believes that
any new interpretation of 'EXPORT_SYMBOL' as being any different from
'EXPORT_SYMBOL_GPL' is entirely invalid; the GPL requires that _all_
exports have the semantics of the new 'EXPORT_SYMBOL_GPL', which means the
extra four characters are entirely redundant.
But since those four extra characters trigger the check for illegal
modules in a way that just EXPORT_SYMBOL does not, it's useful to change
anyway. This action in no way indicates an admission that there is any
legal distinction between the two states, and in particular does not
indicate that the author believes that non-GPL modules may use symbols
exported with EXPORT_SYMBOL alone.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
get_mtd_device() returns NULL in case of any failure. Teach it to return an
error code instead. Fix all users as well.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds get_device() and put_device() methods to the MTD description
structure (struct mtd_info). These methods are called by MTD whenever the MTD
device is get or put. They are needed when the underlying driver is something
smarter then just flash chip driver, for example UBI.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds one more function to the MTD interface to make it possible to
open MTD devices by their names, not only numbers. This is very handy in many
situations. Also, MTD device number depend on load order and may vary, while
names are fixed.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Add a MTD_BLKDEVS Kconfig option to cleanup the makefile a bit
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch has fixed name of map probe for cstm_mips_ixx.c
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up the config option in the #ifdef statements in nand_ecc.c
Signed-off-by: Timo Lindhorst <lindhors@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix printk format warning:
drivers/mtd/maps/physmap.c:93: warning: long long unsigned int format, long unsigned int arg (arg 2)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently, mtd_blkdevs enforces a block size of 512, even if the drivers
can seemingly request a different size. This patch fixes mtd_blkdevs so
block sizes other than 512 work correctly.
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for accessing BIOS flash chips connected to the NVIDIA ck804 southbridge.
Signed-off-by: Ryan Jackson <rjackson@lnxi.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The writel() call accidentally clears all bits in the NDFC_CCR
register (endianess problem). Now __raw_writel() is used instead.
Tested on Bamboo with NAND on chip select 0 and chip select 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch makes the needlessly global mtdpart_setup() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch converts drivers/mtd/nand/rtc_from4.c to use the new
lib/bitrev.c
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We can use the two methods to wait.
1. polling: read interrupt status register
2. interrupt: use kernel ineterrupt mechanism
To use interrupt method, you first connect onenand interrupt pin to your
platform and configure interrupt properly
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
We were resetting cafe->ctl2 to zero after an erase (and also during a
write, but it was correctly reset after that). This meant that ECC reads
after an erase were failing. Doh.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Also use cafe_readl() and cafe_writel() abstraction to make code
slightly cleaner -- especially if we want to use it in PIO mode.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add description of 'raw' in comments for
drivers/mtd/nand/nand_base.c::nand_write_page_syndrome() so 'make xmldocs'
will not spew a warning at us.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being a value which isn't in the table is a case we explicitly check for
in the caller. Don't BUG_ON() because it does actually happen in
practice.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When a flash-based BBT is not used, nand_default_mark_blockbad() is supposed
to mark the block bad in the oob. However, it sets the wrong length variable
so that no bad block marker is in fact written. This patch attempts to
rectify that.
(As note, it seems to be that logically, it shouldn't be necessary to set
both length variables, as one appears to be for the main buffer, and
one for the oob buffer, but this is how it is done in several places,
including the code for the mtd character device MEMWRITEOOB and MEMREADOOB
ioctls. I'm not sure if this is a temporary solution during some rework of
the mtd infrastructure, or whether there is a deeper thought here.)
Signed-off-by: Ricard Wanderlöf <ricardw@axis.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
