Test whether tusb_dma is not NULL before dereferencing
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the board might use external Vbus power supply on musb
interface which would require to program ULPI_BUSCONTROL register.
Adding 'extvbus' flag which can be set from such boards which will
be checked at musb driver files before programming ULPI_BUSCONTROL.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's programming guide dictates how we should handle its
irqs and in which order. Follow that.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The version applied had a few comments which are now
done.
Thanks to Sergei for pointing out.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the Tx abort/teardown logic. We now wait for the teardown
completion interrupt and acknowledge the same by setting the tx_complete
register to 0.
This change is needed to ensure that abort processing works on DM365 platform.
Without this change after completion of abort processing the system is
overwhelmed with continuous stream of abort interrupts.
This change has been tested on all CPPI3.x platforms (DM644x, DM646x, DM35x,
DM36x).
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the work around for a Mentor controller related
bug where it's observed a BULK Tx toggle error on the bus when a
BULK IO gets scheduled on an endpoint that was earlier used for
handling ISOC transaction and needed to start on 1 toggle. When such
a situation arises even if the TXCSR toggle bits are programmed
correctly by the musb driver the data gets transmitted with 0 toggle
which leads to toggle error on the bus and the BULK transaction fails.
In case of MSC write, the device gets reset by the Host.
This Mentor bug is observed on almost all Mentor versions (1.3, 1.5,
1.8). Confirmed on DM644x, DM355, DM365, OMAPL13x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB DMA_INTR register may sometimes read zero when infact there
was a pending interrupt. Workaround this by reading the DMA_COUNT
values for all enabled channels when this condition occurs.
Flag these channels as the ones needing to be serviced.
Additionally, the absence of a debug print meant we would never
catch a spurious DMA interrupt in MUSB. So this patch adds a
debug print in the IRQ handler.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wrapper for reading the DMA count register, analogous
to the one for writing to this register.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's easier to keep up and add more sysfs entries
as necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of these workarounds are already in place, but labeled as affecting
all BF52x parts. Since we have official anomaly numbers now, use those
defines. And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below array index out of bounds issue.
Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84
The data stored in 'aInfo' array exceeds the array size of 78.
This patch increases the size of this array to hold the string
correctly without any memory corruption.
This issue was reported by Klockwork tool.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following NULL pointer dereference issue.
Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.
============
Code Snippet
============
748: request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
csr &= ~(MUSB_RXCSR_AUTOCLEAR
| MUSB_RXCSR_DMAENAB
| MUSB_RXCSR_DMAMODE);
musb_writew(epio, MUSB_RXCSR,
MUSB_RXCSR_P_WZC_BITS | csr);
792: request->actual += musb_ep->dma->actual_len;
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget stalling a zero-length SETUP request results in this error message:
SetupEnd came in a wrong ep0stage idle
In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request. Add the missing '\n' to the error message itself as well...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO. Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.
Update over previous patch to avoid taking the lock if already
taken. Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.
Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a null-pointer dereference bug.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
pointer types lacks a cast
So switch to min_t(size_t, ...).
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
probe() already was on __init, so moving remove() to __exit.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 7723de7e19 (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/musb/musb_host.c:1642:9: warning: symbol 'status' shadows an earlier one
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warnings:
drivers/usb/musb/musb_gadget.c:1161:5: warning: symbol 'musb_gadget_set_halt' was not declared. Should it be static?
drivers/usb/musb/musb_gadget.c:1244:5: warning: symbol 'musb_gadget_set_wedge' was not declared. Should it be static?
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/musb/omap2430.c:314:16: warning: Using plain integer as NULL pointer
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the pointless 'do () while (0)' loop from musb_g_tx() -- it
makes this function symmetric to musb_g_rx()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop playing with musb->lock and abusing musb_gadget_set_halt() in
the code clearing the endpoint halt feature -- instead, manipulate
the registers directly.
While at it, get rid uf unneeded line breaks and over-indentation in
the code setting the endpoint halt feature.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the driver's set_wedge() method by adding the 'wedged' flag
to the 'struct musb_ep'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a5073b5283 (musb_gadget: fix
unhandled endpoint 0 IRQs) somehow missed its key change:
"The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely."
So, the majority of the cases of unhandled IRQs is still unfixed...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB: save hardware revision at init
This can be used later to flag workarounds for issues affecting
particular revisions. Saving this at init avoids having to
read the HWVERS register multiple times in code.
While at it, use macros to extract the version information
instead of using hardcoded values.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The debug code in the DMA ISR uses a %d for a size_t when it should be
using %zu. Otherwise gcc whines with:
drivers/usb/musb/musbhsdma.c: In function 'dma_controller_irq':
drivers/usb/musb/musbhsdma.c:288: warning: format '%d' expects type 'int',
but argument 7 has type 'size_t'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Otherwise we get the link failure:
drivers/built-in.o: In function 'musb_platform_init':
drivers/usb/musb/blackfin.c:300: undefined reference to 'usb_nop_xceiv_register'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since we can't work around anomaly 05000380, throw a build error up and
instruct the user to use a different mode.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we clear the interrupt pending bits at the end, we sometimes return too
fast and have the same interrupt assert itself. There is no way in a
Blackfin system to force a sync of this state, so the hardware manual
instructs people to clear interrupt flags early in their ISR.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only allow USE_MODE1 when the Blackfin part is not affected by anomaly
05000456 (USB Receive Interrupt Is Not Generated in DMA Mode 1) since we
can't support the mode in that case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add some helpful notes about how the driver works around different
anomalies that exist in the on-chip host controller.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not allow MUSB driver to be selected on derivatives that don't have the
MUSB controller on them.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin version of musb_read_target_reg_base() returns a u16 when the
common code expects a (void __iomem *), so update the Blackfin function to
return the right value. This fixes the compile warning:
drivers/usb/musb/musb_core.c: In function 'musb_core_init':
drivers/usb/musb/musb_core.c:1448: warning: assignment makes pointer from
integer without a cast
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Otherwise gcc will whine about epnum/dma_reg being unused when building
for BF54x parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
