Add receive programmed IO mode to reduce receive latency
when using low data rates. The receive FIFO trigger
level of 128 bytes used in DMA mode creates excessive latency
when operating at low data rates. PIO mode is selected when user
application requests data in blocks of less than 128 bytes.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need this for devices that cannot flush and wait, but which do not order
data and modem events. Without it we will hang up before all the data
clears the hardware. Needed for the USB changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers implement this internally, others miss it out. Push the
behaviour into the core code as that way everyone will do it consistently.
Update the dtr rts method to raise or lower depending upon flags. Having a
single method in this style fits most of the implementations more cleanly than
two funtions.
We need this in place before we tackle the USB side
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to check if dev_id is NULL, it never is.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't reset the PLX chip after FW load, which effectively kills
the FW, so that user had to boot manually.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ze needs firmware to be loaded as well as Zo. Move cyz_load_fw one
level upper to achieve that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During tree log replay, we read in the tree log roots,
process them and then free them. A recent change
takes an extra reference on the root node of the tree
when the root is read in, and stores that reference
in root->commit_root.
This reference was not being freed, leaving us with
one buffer pinned in ram for each subvol with
a tree log root after a crash.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
A build error slipped in:
builtin-report.c: In function ‘hist_entry__fprintf’:
builtin-report.c:711: error: format ‘%12d’ expects type ‘int’, but argument 3 has type ‘uint64_t’
Because we got a bit sloppy with those types. uint64_t really sucks,
because there's no printf format for it. So standardize on __u64
instead - for all types that go to or come from the ABI (which is __u64),
or for values that need to be large enough even on 32-bit.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename perf_counter_limit to perf_counter_max_sample_rate and
prohibit creation of counters with a known higher sample
frequency.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the perf_counter_priv knob to perf_counter_paranoia (because
priv can be read as private, as opposed to privileged) and provide
one more level:
0 - permissive
1 - restrict cpu counters to privilidged contexts
2 - restrict kernel-mode code counting and profiling
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds tables of event codes for the generalized cache events for
all the currently supported powerpc processors: POWER{4,5,5+,6,7} and
PPC970*, plus powerpc-specific code to use these tables when a
generalized cache event is requested.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18992.36430.933526.742969@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds the back-end for the PMU on POWER7 processors. POWER7
has 4 fully-programmable counters and two fixed-function counters
(which do respect the freeze conditions, can generate interrupts,
and are writable, unlike PMC5/6 on POWER5+/6).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18992.36329.189378.17992@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit c9690998ef (x86: memtest: remove
64-bit division) introduced following compile warning:
arch/x86/mm/memtest.c: In function 'memtest':
arch/x86/mm/memtest.c:56: warning: comparison of distinct pointer types lacks a cast
arch/x86/mm/memtest.c:58: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
lookup_inline_extent_backref only checks for duplicate backref for data
extents. It assumes backrefs for tree block never conflict.
This patch makes lookup_inline_extent_backref check for duplicate backrefs
for both data and tree block, so that we can detect potential bug earlier.
This is a safety check, strictly speaking it is not required.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch adds the following 2 interfaces for request-stacking drivers:
- blk_rq_prep_clone(struct request *clone, struct request *orig,
struct bio_set *bs, gfp_t gfp_mask,
int (*bio_ctr)(struct bio *, struct bio*, void *),
void *data)
* Clones bios in the original request to the clone request
(bio_ctr is called for each cloned bios.)
* Copies attributes of the original request to the clone request.
The actual data parts (e.g. ->cmd, ->buffer, ->sense) are not
copied.
- blk_rq_unprep_clone(struct request *clone)
* Frees cloned bios from the clone request.
Request stacking drivers (e.g. request-based dm) need to make a clone
request for a submitted request and dispatch it to other devices.
To allocate request for the clone, request stacking drivers may not
be able to use blk_get_request() because the allocation may be done
in an irq-disabled context.
So blk_rq_prep_clone() takes a request allocated by the caller
as an argument.
For each clone bio in the clone request, request stacking drivers
should be able to set up their own completion handler.
So blk_rq_prep_clone() takes a callback function which is called
for each clone bio, and a pointer for private data which is passed
to the callback.
NOTE:
blk_rq_prep_clone() doesn't copy any actual data of the original
request. Pages are shared between original bios and cloned bios.
So caller must not complete the original request before the clone
request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a typo here that had this as sys_writev() instead of
sys_pwritev(), fix this up. sh64 got this right, as did the preadv()
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up a typo in the ll/sc based cmpxchg code which apparently
wasn't getting a lot of testing due to the swapped old/new pair. With
that fixed up, the ll/sc code also starts using it and provides its own
atomic_add_unless().
Signed-off-by: Aoi Shinkai <shinkoi2005@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7722 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
While at it, now when all SuperH Mobile processors
are converted, fix CONFIG_SH_CLK_CPG_LEGACY to depend
on CONFIG_ARCH_SHMOBILE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7366 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch rewrites the sh7343 clock framework code.
The new code makes use of the recently merged div4,
div6 and mstp32 helper code. Both extal and dll are
supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V3 of the sh7724 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and fll are
supported as input clocks to the pll. The div6 clocks are
fed through a divide-by-3 block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains V2 of the sh7723 clock framework
rewrite. The new code makes use of the recently merged
div4, div6 and mstp32 helper code. Both extal and dll
are supported as input clocks to the pll.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the div6 clock helper code to add support
for enable(), disable() and set_rate() callbacks.
Needed by the camera clock enabling board code on Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin configuration and
a machvec structure to Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7722 mode pin and pin function
controller comments.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds comments for the sh7724 mode pins
and pin function controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is sh7723 mode pin V2. Mode pins and
pin function controller comments are added.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the mode pin code to keep the pin
definitions in one place. The mode pins values are now
the value of the bit instead of bit number.
With this patch in place the sh7785 header file contains
mode pin comments. The sh7785 clock code and the sh7785lcr
board code are updated to reflect the new shared mode pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds div6 clock helper code. The div6 clocks
are simply 6-bit divide-by-n modules where n is 1 to 64.
Needed for vclk on sh7722, sh7723, sh7343 and sh7366.
sh7724 needs this even more for vclk, fclka, fclkb,
irdaclk and spuclk.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the per clock offset calculation in
sh_clk_div4_register(). Without this patch the offset
to the frequency table for each clock is incorrect.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'tracing-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
function-graph: always initialize task ret_stack
function-graph: move initialization of new tasks up in fork
function-graph: add memory barriers for accessing task's ret_stack
function-graph: enable the stack after initialization of other variables
function-graph: only allocate init tasks if it was not already done
Manually fix trivial conflict in kernel/trace/ftrace.c
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: introduce module_param oprofile.cpu_type
oprofile: add support for Core i7 and Atom
oprofile: remove undocumented oprofile.p4force option
oprofile: re-add force_arch_perfmon option
* 'rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: rcu_sched_grace_period(): kill the bogus flush_signals()
rculist: use list_entry_rcu in places where it's appropriate
rculist.h: introduce list_entry_rcu() and list_first_entry_rcu()
rcu: Update RCU tracing documentation for __rcu_pending
rcu: Add __rcu_pending tracing to hierarchical RCU
RCU: make treercu be default
We currently log hw.sample_period for PERF_SAMPLE_PERIOD, however this is
incorrect. When we adjust the period, it will only take effect the next
cycle but report it for the current cycle. So when we adjust the period
for every cycle, we're always wrong.
Solve this by keeping track of the last_period.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For easy extension of the sample data, put it in a structure.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When we use variable period sampling, add the period to the sample
data and use that to normalize the samples.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ever since Paul fixed it to unclone the context before taking the
ctx->lock this became a false positive, annotate it away.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
