As QAM_64, QAM_256, and QAM_AUTO all use the same firmware, switching
between these modulations doesn't require a firmware re-load. This also
fixes a mishandled error condition, in which the firmware file is loaded
into the kernel, the clock mode is changed, but then the firmware upload
to the device fails. The modulation change is aborted, but the clock
mode would still be changed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some saa7115-based cards use a different crystal frequency and a different
audio clock generation. Add a new VIDIOC_INT_S_CRYSTAL_FREQ command to be
able to set these values.
Also change the default APLL setting to 0. It makes no sense to have the
audio clock independent from the video clock, this can lead to audio/video
synchronization problems. Setting this to 0 is also consistent with the old
saa7114.c source and the way the Hauppauge Windows driver sets it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- improve handling of the EXTERN input: don't start an unnecessary carrier scan
- improve the LOG_STATUS output
- ensure that a carrier scan is started again when switching back to the tuner.
- set correct prescale for L-NICAM
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is some old code in the or51133 firmware loading function that
has no effect. Left a comment to in case it helps someone trying
to reverse engineer the chip.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
[ARM] 3648/1: Update struct ucontext layout for coprocessor registers
[ARM] Add identifying number for non-rt sigframe
[ARM] Gather common sigframe saving code into setup_sigframe()
[ARM] Gather common sigframe restoration code into restore_sigframe()
[ARM] Re-use sigframe within rt_sigframe
[ARM] Merge sigcontext and sigmask members of sigframe
[ARM] Replace extramask with a full copy of the sigmask
[ARM] Remove rt_sigframe puc and pinfo pointers
[ARM] 3647/1: S3C24XX: add Osiris to the list of simtec pm machines
[ARM] 3645/1: S3C2412: irq support for external interrupts
[ARM] 3643/1: S3C2410: Add new usb clocks
[ARM] 3642/1: S3C24XX: Add machine SMDK2413
[ARM] 3641/1: S3C2412: Fixup gpio register naming
[ARM] 3640/1: S3C2412: Use S3C24XX_DCLKCON instead of S3C2410_DCLKCON
[ARM] 3639/1: S3C2412: serial port support
[ARM] 3638/1: S3C2412: core clocks
[ARM] 3637/1: S3C24XX: Add mpll clock, and set as fclk parent
[ARM] 3636/1: S3C2412: Add selection of CPU_ARM926
[ARM] 3635/1: S3C24XX: Add S3C2412 core cpu support
[ARM] 3633/1: S3C24XX: s3c2410 gpio bugfix - wrong pin nos
...
This reverts commit 786dc1d3d7.
As Al so eloquently points out, the patch is crap. The old code was fine,
the new code was bogus.
It never dereferenced a user pointer, the "->" operator was to an array
member, which gives the _address_ of the member (in user space), not an
actual dereference at all.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: radeon constify radeon microcode
Add i915 ioctls to configure pipes for vblank interrupt.
drm: update radeon to 1.25 add r200 vertex program support
drm: radeon add a tcl state flush before accessing tcl vector space
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (40 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Make auxio a real driver.
[PARPORT] sunbpp: Convert to new SBUS device framework.
[Documentation]: Update probing info in sbus_drivers.txt
[SCSI] qlogicpti: Convert to new SBUS device framework.
[SCSI] esp: Fix bug in esp_remove_common.
[NET] sunhme: Kill useless loop over sdevs in quattro_sbus_find().
[NET] myri_sbus: Kill unused next_module struct member.
[NET] myri_sbus: Convert to new SBUS device layer.
[NET] sunqe: Convert to new SBUS driver layer.
[NET] sunbmac: Convert over to new SBUS device framework.
[NET] sunlance: Convert to new SBUS driver framework.
[NET] sunhme: Convert to new SBUS driver framework.
[NET] sunhme: Kill __sparc__ and __sparc_v9__ ifdefs.
[SCSI] sparc: Port esp to new SBUS driver layer.
[SOUND] sparc: Port amd7930 to new SBUS device layer.
[SBUS]: Rewrite and plug into of_device framework.
[SPARC]: Port of_device layer and make ebus use it.
[SPARC]: Port sparc64 in-kernel device tree code to sparc32.
[SPARC64]: Add of_device layer and make ebus/isa use it.
...
This is the minimal resume trace code to find which device resume (if
any) results in problems. Usually, you'd use the information this
generates as a starting point to adding more fine-grained trace event
points.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Considering that there isn't a lot of hw we can depend on during resume,
this is about as good as it gets.
This is x86-only for now, although the basic concept (and most of the
code) will certainly work on almost any platform.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i915 vblanks can be generated from either pipe a or b, however a disabled
pipe generates no interrupts. This change allows the X server to select
which pipe generates vblank interrupts.
From: Keith Packard <keith.packard@intel.com> via DRM CVS
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add support for r200 vertex programs (R200_EMIT_VAP_PVS_CNTL, and new
packet type for making it possible to address whole tcl vector space
and have a larger count)
From: Roland Scheidegger (DRM CVS)
Signed-off-by: Dave Airlie <airlied@linux.ie>
Do a tcl state flush before accessing tcl vector space. This fixes some
more problems with flickering (bug #6637). drm may not be appropriate
place for this, since doing that flush there might both be overkill and
insufficient in some cases. However, it's hard to figure out when that
flush is needed, so this has to suffice. There does not seem to be a
performance penalty associated with it.
From: Roland Scheidegger (DRM CVS)
Signed-off-by: Dave Airlie <airlied@linux.ie>
ring_head is offset in card memory, not iomem pointer. Fixed, removed
fuckloads of amazingly bogus casts somebody had sprinkled all over the
place.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@linux.ie>
I severely apologize, I was still learning how to program
in C when I wrote this stuff 10 years ago...
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparcspkr and power drivers are converted, to make sure it works.
Eventually the SBUS device layer will use this as a sub-class.
I really cannot cut loose on that bit until sparc32 is given the
same infrastructure.
Signed-off-by: David S. Miller <davem@davemloft.net>
One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/cpufreq/cpufreq_ondemand.c: In function 'do_dbs_timer':
drivers/cpufreq/cpufreq_ondemand.c:374: warning: implicit declaration of function 'lock_cpu_hotplug'
drivers/cpufreq/cpufreq_ondemand.c:381: warning: implicit declaration of function 'unlock_cpu_hotplug'
drivers/cpufreq/cpufreq_conservative.c: In function 'do_dbs_timer':
drivers/cpufreq/cpufreq_conservative.c:425: warning: implicit declaration of function 'lock_cpu_hotplug'
drivers/cpufreq/cpufreq_conservative.c:432: warning: implicit declaration of function 'unlock_cpu_hotplug'
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A process flag to indicate whether we are doing sync io is incredibly
ugly. It also causes performance problems when one does a lot of async
io and then proceeds to sync it. Part of the io will go out as async,
and the other part as sync. This causes a disconnect between the
previously submitted io and the synced io. For io schedulers such as CFQ,
this will cause us lost merges and suboptimal behaviour in scheduling.
Remove PF_SYNCWRITE completely from the fsync/msync paths, and let
the O_DIRECT path just directly indicate that the writes are sync
by using WRITE_SYNC instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
While writing a version of losetup, I ran into the problem that the loop
device was returning total garbage.
It turns out the problem was that this losetup was only issuing the
LOOP_SET_FD ioctl and not issuing a subsequent LOOP_SET_STATUS ioctl. This
losetup didn't have any special status to set, so it left out the call.
The deeper cause is that loop_set_fd sets the transfer function to NULL,
which causes no transfer to happen lo_do_transfer.
This patch fixes the problem by setting transfer to transfer_none in
loop_set_fd.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
