When running the loopback test, resources are not properly released on
completion. This patch frees all transmit resources after running the
loopback test. Tested on ia32 and ppc64 hardware.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
This patch brings the airo driver into line with the current
WEXT specification of signal quality. It also fixes the values
used to determine signal quality and level for MPI & PCMCIA 350
cards. It turns out that BSSListRid.rssi was actually in dBm
for 350 series cards, and that we can use the normalized
signal strength reported by the card as our "quality" value, on
a scale of 0 - 100. Since signal level values are in dBm for
this driver, max_qual->level MUST be 0, as specified in the WEXT
spec. This patch also uses the IW_QUAL constants new in WEXT
version 17.
Signed-off-by: Dan Williams <dcbw@redhat.com>
On Wed, Apr 13, 2005 at 05:36:42PM +0000, Andrew Morton wrote:
> Summary: natsemi: incorrect initialization of IPv6 Neighbor-
> discovery multicast
I've got a pair of FA312 cards and this problem has bothered me
for ages. This has finally prompted me to do something about it :)
Turns out that somebody wasn't following the documentation. We were
doing 16-bit writes to 32-bit registers which led to some addresses
working and others not so lucky.
This patch should fix the problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ayaz wrote an update to the error handling for forcedeth (which I
modified heavily, thus all bugs are mine):
The ERROR4 bit is not a fatal error, it just indicates a mismatch
between the actual packet len and the len according to the 802.3 header.
The patch adds proper handling.
The patch also removes the code that drops all packets with RX_ERROR &
(!RX_FRAMINGERR): ERROR4 errors are also not fatal.
Hi Andrew, Jeff,
The iseries_veth driver is badly behaved in that it will keep TX packets
hanging around forever if they're not ACK'ed and the queue never fills up.
This causes the unregister_netdevice code to wait forever when we try to take
the device down, because there's still skbs around with references to our
struct net_device.
There's already code to cleanup any un-ACK'ed packets in veth_stop_connection()
but it's being called after we unregister the net_device, which is too late.
The fix is to rearrange the module exit function so that we cleanup any
outstanding skbs and then unregister the driver.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Hi Andrew, Jeff,
Under some strange circumstances the iseries_veth driver can leak skbs.
Fix is simply to call dev_kfree_skb() in the right place.
Fix up the comment as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Hi Andrew, Jeff,
The iseries_veth driver doesn't set dev->trans_start in it's TX path. This
will cause the net device watchdog timer to fire earlier than we want it to,
which causes the driver to needlessly reset its connections to other LPARs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Hi Andrew, Jeff,
The iseries_veth driver has a logic bug which means it will erroneously
send packets to LPARs for which we don't have a connection.
This usually isn't a big problem because the Hypervisor call fails
gracefully and we return, but if packets are TX'ed during the negotiation
of the connection bad things might happen.
Regardless, the right thing is to bail early if we know there's no
connection.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
small fixes from CVS that didn't fit elsewhere
Index: linux-2.6/drivers/net/wireless/orinoco.c
===================================================================
Contributors:
Host AP contributors
James Ketrenos <jketreno@linux.intel.com>
Francois Romieu <romieu@fr.zoreil.com>
Adrian Bunk <bunk@stusta.de>
Matthew Galgoci <mgalgoci@parcelfarce.linux.th
eplanet.co.uk>
The options FMV18X and SK_G16 do depend on the non-available
CONFIG_OBSOLETE even in kernel 2.4 - IOW, the last time it was able to
select them was in kernel 2.2 (or even before).
Since it seems noone misses these drivers, this patch removes them.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch removes a NULL check that was useles because it happened
after the first dereference of the variable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains the following cleanups:
- make a needlessly global function static
- make three needlessly global structs static const
Since after moving the now-static stucts to smc-mca.c the file smc-mca.h
was empty except for two #define's, I've also killed the rest of
smc-mca.h .
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use msleep() instead of schedule_timeout()
to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Phil Blundell <pb@nexus.co.uk>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previous patch did not compile cleanly on all architectures so
here's a fixed one.
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previous patch did not compile cleanly on all architectures so
here's a fixed one.
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previous patch did not compile cleanly on all architectures so
here's a fixed one.
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Driver version, white space, comments.
Also enabled ICH-7 support
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fix Wake on lan related issues
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Synchronize interface link state with e100 poll routine
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Render e100 NAPI state machine to be similar to the non-NAPI one.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed msec_delay in osdep to use msleep
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/ixgb/ixgb_osdep.h net-drivers-2.6/drivers/net/ixgb.new/ixgb_osdep.h
Remove hook for suspend. No power management in 10GbE Controllers
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/ixgb/ixgb_main.c net-drivers-2.6/drivers/net/ixgb.new/ixgb_main.c
Reset status in the Rx descriptor prior to handing it to the controller.
Leave three Rx descriptors unused
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/ixgb/ixgb_main.c net-drivers-2.6/drivers/net/ixgb.new/ixgb_main.c
Disable RXO interrupt to decrease recovery time when system is overloaded with data
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/ixgb/ixgb_main.c net-drivers-2.6/drivers/net/ixgb.new/ixgb_main.c
Don't set the RS bit on context descriptors, causes un-necessary bus activity
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/ixgb/ixgb_main.c net-drivers-2.6/drivers/net/ixgb.new/ixgb_main.c
Implement 82546 errata 10 -- first Tx descriptor cannot have more than 2015 byte of data in it or it could hang the transmitter.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Dump information on Tx ring when 'NETDEV: Watchdog' condition is reached
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Delay clean-up of last Tx packet to fix pre-mature writeback issue of Tx descriptors only when TSO is enabled
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Fix kernel panic with 82541 LOM when using a 100M cable
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Enable polling before enabling interrupts -- avoids (in NAPI mode) entering the ISR and returning without doing any work because polling is not enabled. [romieu@fr.zoriel.com]
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_main.c net-drivers-2.6/drivers/net/e1000.new/e1000_main.c
Fix msec-delay definition in e1000_osdep.h to use msleep
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_osdep.h net-drivers-2.6/drivers/net/e1000.new/e1000_osdep.h
Added enhanced functionality to the loopback diags to wrap the descriptor rings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
diff -up net-drivers-2.6/drivers/net/e1000/e1000_ethtool.c net-drivers-2.6/drivers/net/e1000.new/e1000_ethtool.c
The PAGE_SIZE mask is indeed confusing. Use the exact mask for
this context which has nothing to do with memory pages at all.
Also cast to int since the value to compare with is an int.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support to sis900 for the following ethtool ops:
- get_link
- get_settings
- set_settings
- nway_reset
Signed-off-by: Daniele Venzano <webvenza@libero.it>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The size of the incoming frame is not correctly checked.
The RxMaxSize register (0xDA) does not work as expected and incoming
frames whose size exceeds the MTU actually end spanning multiple
descriptors. The first Rx descriptor contains the size of the whole
frame (or some garbage in its place). The driver does not expect
something above the space allocated to the current skb and crashes
loudly when it issues a skb_put.
The fix contains two parts:
- disable hardware Rx size filtering: so far it only proved to be able
to trigger some new fancy errors;
- drop multi-descriptors frame: as the driver allocates MTU sized Rx
buffers, it provides an adequate filtering.
As a bonus, wrong descriptors were not returned to the asic after their
processing.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Consolidate allocation of firmware buffers. In the process, remove
duplication of a workaround for an old symbol firmware bug, and fix a
bug where we could retry the workaround, even if it already failed to
help.
Signed-off-by: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't attempt to manually set the channel in infrastructure mode, the
firmware doesn't like that much. Also don't attempt to override the
firmware's default channel number for IBSS mode (I believe default
channel can vary by regulatory domain).
Signed-off-by: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove the dump_recs debugging iwpriv command. It will be replaced
later with the simpler and more flexible get_rid command.
Signed-off-by: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds an ignore_disconnect module parameter. When enabled, the driver
will continue attempting to send packets even when the firmware has
told us we've lost our link to the AP. On some firmwares this
substantially increases the usable range of the card (presumably
because we have an interrmittent connection, but the firmware is able
to queue the packets for us until we're connected again). On some
other cards, it causes the firmware to fall in a screaming heap :(
(hence, default off).
Signed-off-by: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here's a patch for -mm for now. Not sure whose territory this falls
in, so I'm sending it to everyone I can think of. :)
Some time ago I did some experiments with using PPP multilink over
largish numbers of channels (up to 32). The TCP performance was
woeful due to wildly fluctuating packet latencies, which turned out to
be because we would sometimes split a packet across all 32 channels,
and sometimes we would send a whole packet down a single channel.
This patch fixes those problems by being a bit cleverer about how the
packets are split across the available channels, and in particular, it
waits until at least half of the channels can take another fragment
before starting to split up the next packet.
The patch also fixes a buglet in the multilink reconstruction code
where it would discard incoming packets that had just the multilink
header and no data. Such packets are valid and shouldn't be
discarded.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes the netif_rx_complete() and rx_interrupt_enable
atomic when exiting the poll() method, so to avoid interrupt in poll.
It also fixes the rx interrupt check logic in interrupt handler.
Signed-off-by: Liu Tao <liutao1980@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch converts the 8139too driver to use the iomap infrastructure
for PIO and MMIO instead of playing macro tricks. I also had to fix
read_eeprom(), mdio_sync(), mdio_read(), and mdio_write() to not pass
PIO base address to MMIO read() and write() functions. In addition,
the patch adds proper __iomem annotations for the driver.
Both modes, PIO and MMIO, were tested with a RealTel RTL8139 card on
an x86 box. The 8129 support remains untested due to lack of
hardware.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch adds netpoll support to the 8139cp driver.
The patch needs some tests because I have no NIC of this type for testing.
Applies against linux-2.6.9-rc2-mm3
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
- suspicious length in pci_unmap_single;
- wait for the last frag before freeing the relevant skb;
- no need to crash when facing some unexpected csum combination.
Ross moved. Remove the bad email address so people will find the correct
one in ./CREDITS.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes some needlessly global identifiers static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Arjan van de Ven <arjanv@infradead.org>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During a warm boot the device is in D3 and has troubles coming out of it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tg3_stop_block() errors can be safely ignored since tg3_chip_reset()
always follows tg3_stop_block() calls.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this matches the API used by other link layer like ethernet or token
ring.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* net/irda/irda_device.c::irda_setup_dma() made conditional on
ISA_DMA_API (it uses helpers in question and irda is usable on
platforms that don't have them at all - think of USB IRDA, for
example).
* irda drivers that depend on ISA DMA marked as dependent on
ISA_DMA_API
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers that expect ISA DMA API are marked as such in Kconfig.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kfree() and vfree() can both deal with NULL pointers. This patch removes
redundant NULL pointer checks from the ppp code in drivers/net/
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree(0) is perfectly valid, checking pointers for NULL before calling
kfree() on them is redundant. The patch below cleans away a few such
redundant checks (and while I was around some of those bits I couldn't
stop myself from making a few tiny whitespace changes as well).
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Acked-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable attributes "packed" and "align" when used with struct, should
have the following order:
struct ... {...} __attribute__((packed)) var;
This patch fixes few instances where the variable and attributes are placed
the other way around and had no effect.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Those cards really need A in their names. Otherwise it is pretty hard
to find anything about them on the net.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call pci_enable_device() before looking at IRQ and resources,
and pci_disable_device() when shutting the interface down.
The driver requires this fix or the "pci=routeirq" workaround
on 2.6.10 and later kernels.
Reported and tested by Artur Lipowski.
From: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tg3_restart_ints() is called to re-enable interrupts after tg3_poll()
has finished all the work. It calls tg3_cond_int() to force an interrupt
if the status block updated bit is set. The updated bit will be set if
there is a new status block update sometime during tg3_poll() and it can
be very often. The worst part is that even if all the work has been
processed, the updated bit remains set and an interrupt will be forced
unnecessarily.
The fix is to call tg3_has_work() instead to determine if new work is
posted before forcing an interrupt. The way to force an interrupt is
also changed to use "coalesce_now" instead of "SETINT". The former is
generally a safer way to force the interrupt.
Also deleted the first parameter to tg3_has_work() which is unused.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refreshes the hw rx producer in tg3_rx() so that additional
work posted by the hardware can be processed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that causes tg3_has_work() to always return 1.
rx work is determined by comparing tp->rx_rcb_ptr with the current hw
producer index. The hw producer index is modulo the ring size, but tp-
>rx_rcb_ptr is a free running counter that goes up beyond the ring size.
After the ring wraps around once, tg3_has_work() will always return 1.
The fix is to always do modulo arithmetic on tp->rx_rcb_ptr.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor cleanups for sparc specific drivers (sunbmac, sunqe, sunlance,
sunhme, esp) so that they have a full module version definition that is
consistent with other upstream drivers.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing the open coded equivalents and making ax25 look more like
a linux network protocol, i.e. more similar to inet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MSI test for chips that support MSI. If MSI test fails, it will
switch back to INTx mode and will print a message asking the user to
report the failure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the
offset is not 4-byte aligned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out
is enabled, certain NVRAM registers cannot be written to.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as
output when it is unused.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup proper GPIO settings in tp->grc_local_ctrl before calling
tg3_set_power() state in tg3_get_invariants() and after chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.
On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and
TG3_FLG2_5750_PLUS flags.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite of a couple of troublesome multi-way if statements to use
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of two-way if statements checking for 5750, and/or
5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of three-way if statements checking for 5705, 5750,
and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl.
Next patch will change entry to use pci_ids.h-based definition.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ASIC_REV_5752 definition.
Track-down all references to ASIC_REV_5750 and mirror them with
references to the newly defined ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first of a few installments of PM API updates to match the
recent switch to "pm_message_t". This installment primarily affects
USB device drivers (for USB interfaces), and it changes the handful of
drivers which currently implement suspend methods:
- <linux/usb.h> and usbcore, signature change
- Some drivers only changed the signature, net effect this just
shuts up "sparse -Wbitwise":
* hid-core
* stir4200
- Two network drivers did that, and also grew slightly more
featureful suspend code ... they now properly shut down
their activities. (As should stir4200...)
* pegasus
* usbnet
Note that the Wake-On-Lan (WOL) support in pegasus doesn't yet work; looks
to me like it's missing a request to turn it on, vs just configuring it.
The ASIX code in usbnet also has WOL hooks that are ready to use; untested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/net/irda/stir4200.c
===================================================================
This fixes remaining u32s in drivers/ net.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows to use them on x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows Kconfig to build the MV643xx ethernet driver on Pegasos
(CONFIG_PPC_MULTIPLATFORM) and adds what I think is a missing fix from
Dale's batch, that is remove SA_INTERRUPT and add SA_SHIRQ in there as the
interrupt is shared if I understand things correctly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
