Where devices only have one consumer, passing a consumer clock ID
has no real benefit, and it only encourages wrong implementations of
the clk API. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid unnecessarily pollution of the kernel's namespace by avoiding
mach/hardware.h in mach/io.h. Include this header file where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements poll_get_char and poll_put_char for console polling,
which enables kgdb to work on machines that use the pmac_zilog serial
driver, for example the Apple PowerMac G5.
Signed-off-by: Chris J Arges <arges@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7723 has SCIFA. This module is similer SCI register map, but it has FIFO.
So this patch adds new type(PORT_SCIFA) and change some type checking.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The atmel_serial driver is mismanaging its clock by leaving it on at all
times ... the whole point of clock management is to leave it off unless
it's actively needed, which conserves power!!
Although the kernel doesn't actually hang without my fix, it does
discard quite a lot of early console output.
The result still looks correct:
usart users= 1 on 35000000 Hz, for atmel_usart.0
usart users= 0 off 35000000 Hz, for atmel_usart.2
when using ttyS0 as serial console.
[haavard.skinnemoen@atmel.com: Make sure clock is enabled early for console]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH4-202 doesn't have SCSXX1. But it is treated so that there is SCSPTR1 in
current code. This patch add sci_rxd_in of SH4-202.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change a name of SCSPTR used in sci_rxd_in of SH5-101.
SCSPTR is not declared and will become the error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the netX serial driver tristate (as the help text implied). Make the
serial driver build correctly if the netX serial console is disabled. Do not
allow the netX serial console if the netX serial driver is build as a module.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This reverts commit 5ca8c4852f.
With the killing off of SCIF_ONLY and its spawn in sh-sci, we no longer
require this change, so just revert it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH 7366 has compile bug.
because there is no SCIF_ONLY for SH 7366.
this patch add it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These have the Mainpine PCI identifier on however
Additional paranoia check for Tornado versions added by Alan Cox
(and this time I remembered to do an stg refresh so that the corrections ended
up in these patches not randomly attached to another diff -- Alan)
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the OxSemi 'Tornado' devices.
Reformatted and reworked a bit by Alan Cox
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
In function sn_sal_switch_to_asynch(): drivers/serial/sn_console.c:713:
HZ * SN_SAL_UART_FIFO_DEPTH / SN_SAL_UART_FIFO_SPEED_CPS;
After preprocessing (see defines in patch) this becomes HZ * 16 / 9600 / 10
(associativity from left to right), not equivalent to HZ * 16 / 960.
Looks-obviously-right-to: Tony Luck <tony.luck@intel.com>
Cc: Jes Sorensen <jes@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the needlessly global probe_serial_gsc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SH7723 has two types of SCIF (SCIF and SCIFA).
The current sh-sci driver supports only SCIFA, and calculation methods of SCBRR
are different.
This patch support this methods.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SERIAL_SAMSUNG_DEBUG used printascii() to avoid debugging
through itself when selected as a console. Disable this option
when DEBUG_LL is not set (printascii is unavailable).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Splitting the 8250 code back up to avoid a clash with the NR_IRQS removal
patch introduced a last minute bug. Put back the additional needed lines
for the old lock init
Signed-off-by: Alan Cox <alan@redhat.com>
[ Ingo also reports that this can cause a spontaneous reboot crash with
certain configs, and sends in an identical patch ]
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The multiple drivers share the minor space occupied by a particular major
number, the actual index within the device name's space is indicated by
the tty_driver->name_base + uart_port->line
Another usable formula is (uart_driver->minor - MINOR_BASE) + port->line
Use those to print the device names properly in such situations in
serial_core.c and 8250.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy the simplification from the pty unix98 special case to the generic one.
This allows us to kill off driver->termios_locked entirely which is nice. We
have to whack bits of the cris driver as it meddles in places it shouldn't
providing its own arrays that were never used anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This requires three changes:
1) Remove !SPARC restriction in Kconfig.
2) Move Sparc specific serial drivers before 8250, so that serial
console devices don't change names on us, even if 8250 finds
devices.
3) Since the Sparc specific serial drivers try to use the
same major/minor device namespace as 8250, some coordination
is necessary. Use the sunserial_*() layer routines to allocate
minor number space within TTY_MAJOR when CONFIG_SPARC.
This has no effect on other platforms.
Thanks to Josip Rodin for bringing up this issue and testing
plus debugging various revisions of this patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some inlines from various functions that are called once, are too
big to inline, or are called only from slow path code. This saves around
300 bytes of code for me.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<rmk> talking about leaks - I noticed that the 'check return of
pci_enable_dev()' in the 8250 pci resume function finally made it in
despite my objections against it (causing stuff in higher levels to
leak).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now use the sir_dev/irtty_sir/uart/bfin_serial drivers framework
to monitor the TX status.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
move common variables out of serial headers and into the serial driver and
rename "nr_ports" to "nr_active_ports" so as to easily differentiate
between BFIN_UART_NR_PORTS (the # of available) and nr_ports (the # of enabled)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the scheduled removal of the obsolete
SERIAL_COLDFIRE driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_tty_driver is called at the beginning of the function containing the
lines of code shown in the patch. Thus, put_tty_driver is needed before
returning in the error handling code.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@nr exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = alloc_tty_driver@p1(...)
...
if (x == NULL) S
... when != E = x
when != put_tty_driver(x)
when != goto l;
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << nr.p1;
p3 << nr.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
First move of items out of include/asm-arm/plat-s3c* to their
new homes under arch/arm/plat-s3c/include/plat and
arch/arm/plat-s3c24xx/include/plat directories.
Note, we have to create a dummy arch/arm/plat-s3c/Makefile to
allow us to add arch/arm/plat-s3c/include/plat to the path.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This was added at a time when the compiler did a less than stellar job of
optimizing out dead code. These days this tends to be less of a concern,
so kill it all off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is conditionalized on sh, and disabled for sh64.
Now that SH-5 ties in to the clock framework, the sh64 exception
can be dropped. Additionally, ARM will want to use the same hooks
once SH-Mobile G3 grows clock framework support, so switch these
paths over to HAVE_CLK now.
Once the H8 and ARM sh-sci users hook up HAVE_CLK, the driver can
be switched over to having an outright dependency on it and the
ifdefs can go away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function ks8695uart_set_termios() would cause an unbalanced
enable_irq() generated message to be printk()ed. This is because
there was no book keeping support to remember if the calls to
enable_irq() and disable_irq() were balanced for the modem
control irq.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Presently we don't do much with UPF_IOREMAP other than special case it
for SH-5's onchip_remap() on the early console. Tie this in generically
for platforms that need the remap.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This problem seems to be unnoticed so far:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=b3b708fa2780cd2b5d8266a8f0c3a1cab364d4d2
has changed the serial core behavior to not to suspend the port if the
device is enabled as a wakeup source. If the AT91 system goes to slow
clock mode, the port should be suspended always and the clocks should be
switched off. The patch attached updates the atmel_serial driver to match
the changes in serial core.
Also, the interrupts are disabled when the clock is disabled. If we
disable the clock with interrupts enabled, an interrupt may get stuck. If
this is the DBGU interrupt, this blocks the OR logic at system controller
and thus all other sysc interrupts.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Michael Trimarchi <trimarchimichael@yahoo.it>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're currently passing NULL, and really shouldn't be.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With the change to device tree based setup we no longer need the explicit
Kconfig options for each SCC{1,4} or SMC{1,2} port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds hardware CTSRTS control for pxa serial devices through
termios controls.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A function to contain common code for the size of the resource we
need to allocate or free. OMAP ports need 22 bytes rather than
the standard 8 bytes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires. Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent changes to tighten the check for UARTs that don't correctly
re-assert THRE (01c194d927: "serial 8250:
tighten test for using backup timer") caused problems when such a UART was
opened for the second time - the bug could only successfully be detected
at first initialization. For users of this version of this particular
UART IP it is fatal.
This patch stores the information about the bug in the bugs field of the
port structure when the port is first started up so subsequent opens can
check this bit even if the test for the bug fails.
David Brownell: "My own exposure to this is that the UART on DaVinci
hardware, which TI allegedly derived from its original 16550 logic, has
periodically gone from working to unusable with the mainline 8250.c ...
and back and forth a bunch. Currently it's "unusable", a regression from
some previous versions. With this patch from Will, it's usable."
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alex Williamson <alex.williamson@hp.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupt handler for muxed interrupts (imx2/imx3) was calling
the rts handling subroutine if the RTSS bit was set.
(Which indicates the status of the RTS line), leading to an
interrupt flood on RTS bit low.
This patch fixes the problem by looking at the RTSD bit instead,
indicating a change in the RTS line.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
RX in i.MX27 and i.MX31 UART lines does not work unless the
"RXD Muxed Input Select" bit is set on i.MX27 and i.MX31 processors.
This patch sets the missing RXD mux bit in the UCR3 register.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds extra "out" label to probe function after calling .init form platform data.
Because .init can return error number caused by gpio request fail.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we're just parsing the tuple being passed to this function, we don't
need any device-specific information.
Also, remove the call to pcmcia_validate_cis() from pcmciamtd.c, since it
is already called by the PCMCIA core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
CS_NO_MORE_ITEMS is returned by the CIS tuple reading and parsing code if
the end of a tuple chain is reached. As at least one PCMCIA driver relies
on matching this return value, replace it with -ENOSPC which is now
uniquely used for this purpose within the in-kernel pcmcia subsystem.
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the three remaining pcmcia_get_configuration_info() users:
- pcmciamtd is marked broken anyway.
- serial_cs.c can access the relevant structs directly
- ipwireless didn't use the output
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in misc pcmcia drivers.
CC: Harald Welte <laforge@gnumonks.org>
CC: <linux-parport@lists.infradead.org>
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: Ed Okerson <eokerson@quicknet.net>
CC: linux-serial@vger.kernel.org
CC: boti@rocketmail.com
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It now compiles with the tty changes but isn't tested (which has to be
better than not compiling..
Closes bug #11218
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin peers into the ldisc in an odd way for IRDA snooping which
therefore got missed. Simple enough fix.
Closes bug #11233
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
The removal of drivers/serial/v850e_uart.c originally was in my v850
removal patch, but it seems it got lost somewhere.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serial8250_startup() doesn't disable interrupts while taking the &up->port.lock
which might race against the interrupt handler serial8250_interrupt(), which
when entered, will deadlock waiting for the lock to be released.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As noted by Manuel:
Commit c63847a362 ("sh: Add
SCIF2 support for SH7763.") broke build with CONFIG_EARLY_PRINTK
enabled for me (SH7760):
CC arch/sh/kernel/early_printk.o
/mnt/work/sh7760/kernel/linux-2.6.git/arch/sh/kernel/early_printk.c: In function 'scif_sercon_putc':
/mnt/work/sh7760/kernel/linux-2.6.git/arch/sh/kernel/early_printk.c:84: error: implicit declaration of function 'sci_SCFDR_in'
Move the SH7763 definitions out on their own, so they don't create additional
confusion within the SH7760/SH7780/SH7785 block. Restore the deleted
SCFDR definition for these parts.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces baudrate setting support via the generic clock API.
When present the optional device tree clock property is used instead of
fsl-cpm-brg. Platforms can then define complex clock schemes, to output
the serial clock on an external pin for instance.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch replaces the get_mctrl/set_mctrl stubs with modem control line
read/write access through the GPIO lib.
Available modem control lines are described in the device tree using GPIO
bindings. The driver expect a GPIO pin for each of the CTS, RTS, DCD, DSR,
DTR and RI signals. Unused control lines can be left out.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Before setting STOP_TX, set _brkcr to 0 so the SMC does not send a break
character. The driver appears to properly re-initialize _brkcr when the
SMC is restarted.
Do not interrupt RX/TX when the termios is being adjusted; it results in
corrupted characters appearing on the line.
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to the generic console support code that happened a while ago
introduced a scenario where the initial console is used in parallel with
the final console during a brief period when switching between the two is
in progress. During that time a message about the switch-over is printed.
With some combinations of chips, firmware and drivers, such as the DEC
DZ11 clone used with the DECstation, a hang may happen because the
firmware used for the initial console may not expect the state of the chip
after it has been initialised by the driver.
This is a workaround for the DZ11 which reuses the power-management
callback to keep the transmitter of the line associated with the console
enabled. It reflects the consensus reached in a discussion a while ago.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to the generic console support code that happened a while ago
introduced a scenario where the initial console is used in parallel with
the final console during a brief period when switching between the two is
in progress. During that time a message about the switch-over is printed.
With some combinations of chips, firmware and drivers, such as the Zilog
Z85C30 SCC used with the DECstation, a hang may happen because the
firmware used for the initial console may not expect the state of the chip
after it has been initialised by the driver. This is not a bug in the
firmware, as some registers it would have to examine are write-only.
This is a workaround for the Z85C30 which reuses the power-management
callback to keep the transmitter of the line associated with the console
enabled. It reflects the consensus reached in a discussion a while ago.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a no-name PCI card. I found no reference to a producer so I used
"UNKNOWN_0x1584" as the name.
Full lspci:
01:07.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1584
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- \
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- \
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 1: I/O ports at ec00 [size=128]
Region 2: I/O ports at e480 [size=32]
Region 3: I/O ports at e400 [size=8]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA \
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] #06 [0080]
Capabilities: [4c] Vital Product Data
After:
0000:01:07.0: ttyS4 at I/O 0xe480 (irq = 10) is a 16550A
0000:01:07.0: ttyS5 at I/O 0xe488 (irq = 10) is a 16550A
0000:01:07.0: ttyS6 at I/O 0xe490 (irq = 10) is a 16550A
0000:01:07.0: ttyS7 at I/O 0xe498 (irq = 10) is a 16550A
Signed-off-by: Catalin(ux) M BOIE <catab@embedromix.ro>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel 82571 has a "Serial Over LAN" feature that doesn't properly
implements the receiving of break characters. When a break is received,
it doesn't set UART_LSR_DR and unless another character is received, the
break won't be received by the application.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.
There also seems to be noone willing to bring this port back into a usable
state.
This patch therefore removes the v850 port.
If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add in console polling hooks for the cpm uart for use with kgdb and
kgdboc.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: galak@kernel.crashing.org
I missed the cpm_uart one. Thanks to Kumar Gala for reporting it. A double
check found samsung also needed fixing up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With SMP kernels _irqsave spinlock disables only local interrupts, while
the shared serial interrupt could be assigned to the CPU that is not
currently starting up the serial port.
This might cause issues because serial8250_startup() routine issues
IRQ-triggering operations before registering the port in the IRQ chain
(though, this is fine to do and done explicitly because we don't want to
process any interrupts on the port startup).
With RT kernels and preemptable hardirqs, _irqsave spinlock does not
disable local hardirqs, and the bug could be reproduced much easily:
$ cat /dev/ttyS0 &
$ cat /dev/ttyS1
irq 42: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[C0475EB0] [C0008A98] show_stack+0x4c/0x1ac (unreliable)
[C0475EF0] [C004BBD4] __report_bad_irq+0x34/0xb8
[C0475F10] [C004BD38] note_interrupt+0xe0/0x308
[C0475F50] [C004B09C] thread_simple_irq+0xdc/0x104
[C0475F70] [C004B3FC] do_irqd+0x338/0x3c8
[C0475FC0] [C00398E0] kthread+0xf8/0x100
[C0475FF0] [C0011FE0] original_kernel_thread+0x44/0x60
handlers:
[<c02112c4>] (serial8250_interrupt+0x0/0x138)
Disabling IRQ #42
After this, all serial ports on the given IRQ are non-functional.
To fix the issue we should explicitly disable shared IRQ before
issuing any IRQ-triggering operations.
I also changed spin_lock_irqsave to the ordinary spin_lock, since it
seems to be safe: chain does not contain new port (yet), thus nobody
will interfere us from the ISRs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty pointer has been moved into a tty_port field, so we need to use
->info->port.tty instead of just ->info->tty. Fixes these build errors:
David Brownell <david-b@pacbell.net> wrote:
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_ring':
> drivers/serial/atmel_serial.c:665: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_dma':
> drivers/serial/atmel_serial.c:672: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_startup':
> drivers/serial/atmel_serial.c:797: error: 'struct uart_info' has no member named 'tty'
> make[2]: *** [drivers/serial/atmel_serial.o] Error 1
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile errors in SGI console drivers caused by changes to the
tty_port structures in the linux-next tree.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (powerpc allyesconfig) failed like this:
drivers/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/serial/pmac_zilog.c:245: error: 'struct uart_info' has no member named 'tty'
drivers/serial/pmac_zilog.c:250: error: 'struct uart_info' has no member named 'tty'
I applied the patch below (which builds but may, or may not, be correct).
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.auhttp://www.canb.auug.org.au/~sfr/
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (sparc64 defconfig) failed like this:
drivers/serial/sunhv.c: In function `receive_chars':
drivers/serial/sunhv.c:188: error: structure has no member named `tty'
drivers/serial/sunsu.c: In function `receive_chars':
drivers/serial/sunsu.c:314: error: structure has no member named `tty'
drivers/serial/sunsab.c: In function `receive_chars':
drivers/serial/sunsab.c:121: error: structure has no member named `tty'
I applied the following patch (which, again, may not be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the serial_core based drivers to use the new tty_port structure.
We can't quite use all of it yet because of the dynamically allocated
extras in the serial_core layer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).
While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid dumping garbage to the serial port when the tty is flushed. This
tends to happen when rebooting from a serial console.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial drivers using DMA (like the atmel_serial driver) tend to get very
confused when the xmit buffer is flushed and nobody told them. They
also tend to spew a lot of garbage since the DMA engine keeps running
after the buffer is flushed and possibly refilled with unrelated data.
This patch adds a new flush_buffer operation to the uart_ops struct,
along with a call to it from uart_flush_buffer() right after the xmit
buffer has been cleared. The driver can implement this in order to
syncronize its internal DMA state with the xmit buffer when the buffer
is flushed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.
This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem. This encapsulation
is important because a future patch will change the implementation
of those resource options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The SERIAL_SAMSUNG needs SERIAL_CORE but doesn't select it, leading to a
build failure. Adding a 'select SERIAL_CORE' cure the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: (31 commits)
avr32: Fix typo of IFSR in a comment in the PIO header file
avr32: Power Management support ("standby" and "mem" modes)
avr32: Add system device for the internal interrupt controller (intc)
avr32: Add simple SRAM allocator
avr32: Enable SDRAMC clock at startup
rtc-at32ap700x: Enable wakeup
macb: Basic suspend/resume support
atmel_serial: Drain console TX shifter before suspending
atmel_serial: Fix build on avr32 with CONFIG_PM enabled
avr32: Use a quicklist for PTE allocation as well
avr32: Use a quicklist for PGD allocation
avr32: Cover the kernel page tables in the user PGDs
avr32: Store virtual addresses in the PGD
avr32: Remove useless zeroing of swapper_pg_dir at startup
avr32: Clean up and optimize the TLB operations
avr32: Rename at32ap.c -> pdc.c
avr32: Move setup_platform() into chip-specific file
avr32: Kill special exception handler sections
avr32: Kill unneeded #include <asm/pgalloc.h> from asm/mmu_context.h
avr32: Clean up time.c #includes
...
Set port->fifosize to the software FIFO size, and update the port timeout
when the baud rate is modified. SCC ports have an optional 32 byte hardware
FIFO which is currently not taken into account, as there is no documented way
to check when the FIFO becomes empty.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix CPM serial port corruption when running with CONFIG_PREEMPT_RT.
Userland usage of console, and kernel printf's were stepping on each others toes.
Also only take lock if not in an oops.
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I had 8250.nr_uarts=16 in the boot line of a test kernel and I had a weird
mysterious crash in sysfs. After taking an in-depth look I realized that
CONFIG_SERIAL_8250_NR_UARTS was set to 4 and I was walking off the end of
the serial8250_ports array.
Ouch!!!
Don't let this happen to someone else.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the statically initialized tables from the i.MX serial
driver and makes the driver fully dependent on the information provided by
the platform_device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We assumed a 16MHz reference frequency for the UART. While this
is true for i.MX1 most of the time it is not true for MX27/MX31.
Also, add handling for the ONEMS register which is present on
newer versions of the chip and pass a sane minimum baudrate to
uart_get_baud_rate().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As reported by Vipul Gandhi, the current serial_match_port() doesn't work
for tty-devices using dynamic major number allocation. Fix it.
It oopses if you suspend a serial port with _dynamic_ major number. ATM,
I think, there's only the drivers/serial/jsm/jsm_driver.c driver, that
does it in-tree.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Vipul Gandhi <vcgandhi1@aol.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add attribute to show the current clock source for the serial
driver and remove old and annoying debug output.
Note, this only currently shows the current source with a
"* " prefix to indicate that it is the current source. Future
code will list all the clock sources, with the non-selected
one with " " prefix.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
PATCH FOLLOWS
KernelVersion: 2.6.26-rc3
The original driver had an MODULE_LICENSE statement for GPL,
but no explict license in the header of the file. To make
this more explicit, and since I am the original authour,
we will add a GPLv2 header.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the changelog which should really be found
in the version control system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Funny things may happen if we stop the USART clock before the shifter is
empty. Prevent this from happening by waiting until the shifter is
completely drained before allowing suspend to continue.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
AVR32 doesn't have at91_suspend_entering_slow_clock(). Just assume the
clock will keep running for now.
David has a better solution for this, but this works for now. Leaving
the USART clock running won't prevent the PM code from entering deep
power-down modes anyway.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Now that arch/ppc is gone we always define CONFIG_PPC_CPM_NEW_BINDING so
we can remove all the code associated with !CONFIG_PPC_CPM_NEW_BINDING.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This allows other threads to run when the serial driver polls the CTS
PIN in a loop.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This is the patch that follows Linus's modification about set_ldisc.
Graf has built and tested it on BF537 using Linus's git Tree.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
I made a change to u-boot that used the FP (Fractional Part) field of BRGR
to achieve more accurate baud rate generation. Unfortunately, the
atmel_serial driver looks at the whole BRGR register when trying to detect
the baud rate that the port is currently running at, so setting FP to a
nonzero value breaks the baud rate detection.
I'll sit on the u-boot patch for a while longer, but this is clearly a
bug in the atmel_serial driver which should be fixed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers are using too generic "serial" name for driver_name, this
might cause issues, like this:
Freescale QUICC Engine UART device driver
proc_dir_entry 'serial' already registered
Call Trace:
[cf82de50] [c0007f7c] show_stack+0x4c/0x1ac (unreliable)
[cf82de90] [c00b03fc] proc_register+0xfc/0x1ac
[cf82dec0] [c00b05c8] create_proc_entry+0x60/0xac
[cf82dee0] [c00b23dc] proc_tty_register_driver+0x60/0x98
[cf82def0] [c016dbd8] tty_register_driver+0x1b4/0x228
[cf82df20] [c0184d70] uart_register_driver+0x144/0x194
[cf82df40] [c030a378] ucc_uart_init+0x2c/0x94
[cf82df50] [c02f21a0] kernel_init+0x98/0x27c
[cf82dff0] [c000fa74] kernel_thread+0x44/0x60
^^ The board is using ucc_uart.c and 8250.c, both registered as
"serial".
This patch fixes two drivers that are using "serial" for driver_name and
not "ttyS" for dev_name. Drivers that are using "ttyS" for dev_name, will
conflict anyway, so we don't bother with these.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-By: Timur Tabi <timur@freescale.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 64e9159f5d ("serial_core:
uart_set_ldisc infrastructure") introduced the ability for low-level
serial drivers to be informed when the tty ldisc changes.
However, the actual tty-layer function that does this callback for
serial devices was declared with the wrong type, having a spurious and
unused 'ldisc' argument.
This fixed the resulting compiler warning by just removing it.
Acked-by: Blithering Idiot <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty layer provides a callback that is used when the line discipline
is changed. Some hardware uses this to configure hardware specific
features such as IrDA mode on serial ports. Unfortunately the serial
layer does not provide this feature or pass it down to drivers.
Blackfin used to hack around this by rewriting the tty ops, but those are
now properly shared and const so the hack fails. Instead provide the
proper operations.
This change plus a follow up from the Blackfin guys is needed to avoid
blackfin losing features in this release.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Russell pointed out, original patch will break some serial configurations
because of the dependency of the <asm/serial.h> header file.
Revert it first and try to find out other solution later
Cc: Javier Herrero <jherrero@hvsistemas.es>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
enable_irq_wake() and disable_irq_wake() need to be balanced. However,
serial_core.c calls these for different conditions during the suspend and
resume functions...
This is causing a regular WARN_ON() as found at
http://www.kerneloops.org/search.php?search=set_irq_wake
This patch makes the conditions for triggering the _wake enable/disable
sequence identical.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the InstaShield IS-400 four port RS-232 PCI card.
Signed-off-by: Ignacio García Pérez <iggarpe@t2i.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin SPORTS UART Driver: converting BFIN->BLACKFIN
Blackfin serial driver: add extra IRQ flag for 8250 serial driver
8250 Serial Driver: Added support for 8250-class UARTs in HV Sistemas H8606 board
Blackfin arch: Fix bug - USB fails to build for BF524/BF526
Blackfin arch: update boards defconfig files
Blackfin arch: IO Port functions to read/write unalligned memory
Blackfin arch: enable a choice to provide 4M DMA memory
Blackfin arch: cleanup the icplb/dcplb multiple hit checks
Blackfin arch: Add workaround to read edge triggered GPIOs
Blackfin arch: Sync channel defines with struct dma_register dma_io_base_addr.
Blackfin arch: Check for Anomaly 05000182
[Blackfin] arch: rename bf5xx-flash to bfin-async-flash
[Blackfin] arch: Blackfin checksum annotations
Added support for 8250-class UARTs in HV Sistemas H8606 board,
modification in 8250.c driver for correct compilation with Blackfin
Besides, I think that there is more people using 8250-class UARTs
with a different hardware than the H8606 board. This code can be shared
by them.
Signed-off-by: Javier Herrero <jherrero@hvsistemas.es>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Schedule a removal for this driver. Alternative driver is available for
a while now.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (21 commits)
Blackfin Serial Driver: abstract away DLAB differences into header
Blackfin Serial Driver: macro away the IER differences between processors
[Blackfin] arch: remove useless IRQ_SW_INT defines
[Blackfin] arch: protect linux/usb/musb.h include until the driver gets mainlined
[Blackfin] arch: protect linux/usb/isp1362.h include until the driver gets mainlined
[Blackfin] arch: add EBIU supporting for BF54x EZKIT SMSC LAN911x/LAN921x families embedded ethernet driver
[Blackfin] arch: Set spi flash partition on bf527 as like bf548.
[Blackfin] arch: fix bug - Remove module will not free L1 memory used
[Blackfin] arch: fix wrong header name in comment
[Blackfin] arch: Fix BUG - spi flash on bf527 ezkit would fail at mount
[Blackfin] arch: add twi_lcd and twi_keypad i2c board info to bf527-ezkit
[Blackfin] arch: Add physmap partition for BF527-EZkit
[Blackfin] arch: fix gdb testing regression
[Blackfin] arch: disable single stepping when delivering a signal
[Blackfin] arch: Delete unused (copied from m68k) entries in asm-offsets.c.
[Blackfin] arch: In the double fault handler, set up the PT_RETI slot
[Blackfin] arch: Support for CPU_FREQ and NOHZ
[Blackfin] arch: Functional power management support: Add CPU and platform voltage scaling support
[Blackfin] arch: fix bug - breaking the atomic sections code.
[Blackfin] arch: Equalize include files: Add VR_CTL masks
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (37 commits)
SH: catch negative denormal_subf1() retval in denormal_add()
sh: Fix DMAC base address for SH7709S
sh: update smc91x platform data for se7206.
sh: Stub in cpu_to_node() and friends for NUMA build.
sh: intc register modify fix
sh: no high level trigger on some sh3 cpus
sh: clean up sh7710 and sh7720 intc tables
sh: add interrupt ack code to sh3
sh: unify external irq pin code for sh3
sh-sci: avoid writing to nonexistent registers
sh-sci: sh7722 lacks scsptr registers
sh-sci: improve sh7722 support
sh: reset hardware from early printk
sh: drain and wait for early printk
sh: use sci_out() for early printk
sh: add memory resources to /proc/iomem
sh: add kernel bss resource
sh: fix sh7705 interrupt vector typo
sh: update smc91x platform data for se7722
sh: update smc91x platform data for MigoR
...
I noticed that
static void uart_flush_buffer(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
struct uart_port *port = state->port;
unsigned long flags;
/*
* This means you called this function _after_ the port was
* closed. No cookie for you.
*/
if (!state || !state->info) {
WARN_ON(1);
return;
}
is too late for checking state != NULL.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only write to hardware in SCI_OUT() if the register size is valid.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7722 serial ports all lack SCSPTR registers, so mark them as
nonexistent in the register table.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve sh7722 support for SCIF1 and SCIF2 and separate code
from sh7366 implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
mpc52xx_uart_int and __uart_put_char both try to acquire the
port->lock. Therefore the function sequence of:
mpc52xx_uart_int--> ...-->flush_to_ldisc-->...-->__uart_put_char
can potentially trigger a deadlock. To avoid this deadlock a fix
similar to that found in the 8250.c serial driver is applied. The
deadlock is avoided by releasing the lock before pushing a buffer
and reacquiring it when completed.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add new PCI Express Neo/JSM board to the supported list of drivers in
the JSM driver.
Signed-off-by: Scott Kilau <scottk@digi.com>
Acked-by: Ananda V <avenkat@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Stop drivers calling their own flush method indirectly, it obfuscates code
and it will change soon anyway
- A few more lock_kernel paths temporarily needed in some driver internal
waiting code
- Remove private put_char method that does a write call for one char - we
have that anyway
- Most but not yet all of the termios copy under lock fixing (some has other
dependencies to follow)
- Note a few locking bugs in drivers found in the process
- Kill remaining [ab]users of TIOCG/SSOFTCAR in the driver, these must go to
fix the termios locking
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
