The modem was detected, the ttyUSB{0,1,2} appeared, a call could be
made, and the expected data rate was achieved. Tested for an hour or
two, total of 100Mb. I shall do more testing.
Signed-off-by: James Cameron <quozl@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes the keyspan driver after the addition of additional
checking of driver requirements introduced in usb-serial.c
commit 063a2da8f0. The initialization
of the keyspan usb_serial_driver structs were not initializing the
num_interrupt_out field and the additional checking was rejecting
the end point so the driver wouldn't finish initializing.
This commit initializes the fields to NUM_DONT_CARE.
It works for the keyspan USA-49WG and doesn't break the USA-19HS
which are the two keyspan devices I have to test with.
Signed-off-by: Clark Rawlins <clark.rawlins@escient.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes a bug/inconsistency revealed by the additional sanity checking in
commit 063a2da8f0
introduced in the original 2.6.24 branch.
The Handspring Visor / PalmOS 4 device structure defines .num_bulk_out=2
but the usb-serial probe returns num_bulk_out=3, triggering the check in
the above commit and forcing a bail out when the device (a Garmin iQue in
my case) attempts to connect. The patch bumps the expected number of
endpoints to 3.
FWIW, this patch will probably solve the following kernel bug report for
Treo users (identical symptoms, different model PalmOS units):
<http://bugzilla.kernel.org/show_bug.cgi?id=10118>
Signed-off-by: Brad Sawatzky <brad+kernel@swatter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the Telegesys ETRX2USB which
works fine with the cp2101 driver.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Tested-by: Xavier Carcelle <xavier.carcelle@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The changes introduced in commit
063a2da8f0 changed the semantics of the
num_interrupt_in, num_interrupt_out, num_bulk_in and num_bulk_out
entries of the usb_serial_driver struct to be the number of endpoints
the device has when probed.
This patch changes the ti_1port_device usb_serial_driver struct to
reflect this change. The single port devices only have 1
bulk_out endpoint in their initial configuration, and so this patch
changes the number of other types to NUM_DONT_CARE.
The same change probably needs doing to the ti_2port_device struct,
but I don't have a two port device at hand.
Signed-off-by: Robert Spanton <rspanton@zepler.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the MC8775 device to the sierra driver.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
while I was adding autosuspend to that driver I noticed a few issues.
You were having DMAed buffers as a part of a structure.
This will fail on platforms that are not DMA-coherent (arm, sparc, ppc, ...)
Please test this patch to fix it.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: Mirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the option driver with a lot more novatel driver ids.
From: Dirk DeSchepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for UPS Powercom USB interface (0d9f:0002) in chip CY7C63723.
In my case, this Powercom BNT800AP.
Signed-off-by: Dmitry Shapin <shapin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nobody should be using the generic usb-serial for anything other than
testing. Still, it's not a good thing that it's easy to lock up. There
is a traceback from NMI oopser here:
https://bugzilla.redhat.com/show_bug.cgi?id=431379
But in short, if a line discipline has a chance to echo anything, input
can loop back a write method. So, don't call tty_flip_buffer_push from
under a lock taken on write path.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.
The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: Kevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the mos7820/7840-based B&B USOPTL4_2/USOPTL4_4 USB/RS485
converter to mos7840.c
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the Onda H600/ZTE MF33 device from the sierra driver to the option
driver.
The reason it was moved is because the sierra driver is starting to support
more and more sierra proprietary features, so it makes more sense to keep
sierra only devices in there.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a small patch to add support for a rebranded Novatel modem (see
http://ubuntuforums.org/archive/index.php/t-608388.html for details).
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver
- violates DMA coherency rules
- allocates ~16500 bytes in one chunk
This patch splits out the buffers and uses __get_free_page() to avoid
higher order allocations.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-By: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device setup did miss to initialize the num_interrupt_out field, thus
failing to successfully complete the probe function.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 04d06ad0f1 have added menuconfig support
for the whole USB Kconfig, but there are still menuconfig need for usb/serial,
usb/atm, and usb/gadget, so that the user can disable all the options in that
menu at once instead of having to disable each option separately.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these drivers abused intfdata in close() as flags for binding.
That races with reprobing of those devices. This patch fixes that by using
the flag and the locks introduced with the patch against mos7720.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If disconnect() is called for a logical disconnect, no more IO must be
done after disconnect() returns, or the old and new drivers may conflict.
This patch avoids this by using the flag and lock introduced by the earlier
patch for the mos7720 driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Rename the copied buffer functions from pl2303 to oti6858 to avodi
confusion
- Initialise speeds properly
- Use modern baud rate handling
- Remove GSERIAL/SSERIAL ioctl hacks that reference termios unlocked
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this covers the rest of the obvious cases by using the flags
and locks to guard against disconnect which were introduced
in the earlier patch against mos7720.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If disconnect() is called for a logical disconnect, no more IO must be
done after disconnect() returns, or the old and new drivers may conflict.
This patch avoids this by using the flag and lock introduced by the earlier
patch for the mos7720 driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in an error case memory already allocated must be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver uses usb_get_intfdata() == NULL as a test for disconnect().
You must not do that as this races with probe(). By the time you test
your erstwhile interface may already be somebody else's interface.
This fixes the close() method of cypress_m8 to use the recently introduced
flag and use locking against disconnect() where required in close().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
People keep trying to add entries to this section of the driver for
things. That's what the Changelog is supposed to be for, not the .c
file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When building an external module, the ezusb_* functions are not defined
if we haven't loaded any built'in module that use them (whiteheat,
keyspan, ...).
This patch allow to build those functions even if we only have selected
the usbserial generic driver.
Signed-off-by: Paul Chavent <paul.chavent@fnac.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following improvements were made:
- Fixed control line issue where asserting DTR on ep5 would close ep2
- Added support for calc_num_ports (will help support future composite
devices)
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors
There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.
I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.
I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't pass NULL into termios functions when calling them internally
Remove all the crap which then checks for NULL which can't occur now
Clear CMSPAR as it is not supported
Report the baud rate back to the caller properly (See FIXME someone with
the docs)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove internal NULL passing in termios code
Remove all the if checks it causes
Encode the baud rate back properly
Clear CMSPAR as it is not supported
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove lots of NULL checks that can no longer occur
Encode the baud rate back into the termios (again someone with docs see
FIXME to improve this further)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Sonntag, 16. Dezember 2007 05:23:47 schrieb Andrew Morton:
> On Sat, 15 Dec 2007 07:08:52 -0800 (PST) bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=9573
> > There's a null pointer dereference on drivers/usb/serial/whiteheat.c as
> > follows:
> >
> > (1) line 613: the test "if (port->tty)" implies that null is a legal value
> > for "port->tty" at that point
> >
> > (2) neither firm_open nor firm_purge initialize "port->tty"
drivers/usb/serial/usb-serial::serial_open() sets port->tty
The check for NULL is bogus. This patch removes the check.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A tester with actual hardware would be useful
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this fix, the pl2303 usb-serial adapter would not suspend properly
unless it had been opened first. A pl2303 type_1 chip will still break if the
system is hibernated while the RS-232 connector is powered by another system.
This was broken before, and a reset resume does not fix it. All other suspend
and autosuspend scenarios work with ATEN pl2303 adaptors with HX and type_1 chips.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace the FISH and SOUP macros that violated the macro guidelines in CodingStyle.
Turn them into function calls with clearer variable names.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Edgeport USB Serial Converter: convert semaphore es_sem to the
mutex API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also fixes a sparse warning that symbol 'result' shadows an earlier one.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Claim the interface for a USB to serial converter when the tty is open,
and release the interface when the tty is closed.
If a driver doesn't provide a resume function, use the generic resume
instead.
Make sure the generic resume function does not submit the URBs if we're
coming back from autosuspend. On autoresume, we know that the open
function will be called next, which will attempt to submit the URBs. If
we submit them in the resume function, the open will fail.
This works for:
- autosuspend
- suspending with the tty open or closed
- hibernate with the tty closed
A hibernate (or a suspend that causes the USB subsystem to lose power)
has issues. If you have the tty open when you hibernate, a new tty will
be created when the device re-enumerates during resume.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb serial method set_termios() is called for the first time from
open() method in order to set up the termios structure with the default
device's settings, ignoring the current settings. Once it's initialized,
the next set_termios() calls will update the device with the
tty->termios settings.
Currently USB serial console code calls the driver open() method without
a tty and after that will allocate a fake tty and termios so the command
line arguments can be applied to the device
(console=ttyUSB0,115200,...). This makes the driver overwrite the
termios with the default settings and not applying the command line
options.
This patch changes usb_console_setup() to allocate the fake tty and
termios before the open() method is called.
Tested successfully with a pl2303
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a usb serial adapter is used as console, the usb serial console
driver bumps the open_count on the port struct used but doesn't attach
a real tty to it (only a fake one temporaly). If this port is opened later
using the regular character device interface, the open method won't
initialize the port, which is the expected, and will receive a brand new
tty struct created by tty layer, which will be stored in port->tty.
When the last close is issued, open_count won't be 0 because of the
console usage and the port->tty will still contain the old tty value. This
is the last ttyUSB<n> close so the allocated tty will be freed by the
tty layer. The usb_serial and usb_serial_port are still in use by the
console, so port_free() won't be called (serial_close() ->
usb_serial_put() -> destroy_serial() -> port_free()), so the scheduled
work (port->work, usb_serial_port_work()) will still run. And
usb_serial_port_work() does:
(...)
tty = port->tty;
if (!tty)
return;
tty_wakeup(tty);
which causes (manually copied):
Faulting instruction address: 0x6b6b6b68
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT PowerMac
Modules linked in: binfmt_misc ipv6 nfs lockd nfs_acl sunrpc dm_snapshot dm_mirror dm_mod hfsplus uinput ams input_polldev genrtc cpufreq_powersave i2c_powermac therm_adt746x snd_aoa_codec_tas snd_aoa_fabric_layout snd_aoa joydev snd_aoa_i2sbus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc pmac_zilog serial_core evdev ide_cd cdrom snd appletouch soundcore snd_aoa_soundbus bcm43xx firmware_class usbhid ieee80211softmac ff_memless firewire_ohci firewire_core ieee80211 ieee80211_crypt crc_itu_t sungem sungem_phy uninorth_agp agpart ssb
NIP: 6b6b6b68 LR: c01b2108 CTR: 6b6b6b6b
REGS: c106de80 TRAP: 0400 Not tainted (2.6.24-rc2)
MSR: 40009032 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
TASK = c106b4c0[5] 'events/0' THREAD: c106c000
GPR00: 6b6b6b6b c106df30 c106b4c0 c2d613a0 00009032 00000001 00001a00 00000001
GPR08: 00000008 00000000 00000000 c106c000 42004028 00000000 016ffbe0 0171a724
GPR16: 016ffcf4 00240e24 00240e70 016fee68 016ff9a4 c03046c4 c0327f50 c03046fc
GPR24: c106b6b9 c106b4c0 c101d610 c106c000 c02160fc c1eac1dc c2d613ac c2d613a0
NIP [6b6b6b68] 0x6b6b6b68
LR [c01b2108] tty_wakeup+0x6c/0x9c
Call Trace:
[c106df30] [c01b20e8] tty_wakeup+0x4c/0x9c (unreliable)
[c106df40] [c0216138] usb_serial_port_work+0x3c/0x78
[c106df50] [c00432e8] run_workqueue+0xc4/0x15c
[c106df90] [c0043798] worker_thread+0xa0/0x124
[c106dfd0] [c0048224] kthread+0x48/0x84
[c106dff0] [c00129bc] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Slab corruption: size-2048 start=c2d613a0, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c01b16d8>](release_one_tty+0xbc/0xf4)
050: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c2d60b88, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c00f30ec>](show_stat+0x410/0x428)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
This patch avoids this, clearing port->tty considering if the port is
used as serial console or not
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently usb serial console support ignores the device and always use
ttyUSB0.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TI 3410/5052 USB Serial: convert semaphore td_open_close_lock to the mutex
API.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a Dell wireless 5520 card with a different USB ID - specifically, 8136
instead of 8137. Attached a small patch to add support, and the output of an
'ati3'.
If we could get this in, that'd be sweet. ;) Thanks!
nc@knight:~/tmp/linux-2.6.24-rc8/drivers/usb/serial$ lsusb | grep 8136
Bus 001 Device 005: ID 413c:8136 Dell Computer Corp.
nc@knight:~/tmp/linux-source-2.6.23/drivers/usb/serial$ cu -l ttyUSB0 -s 115200
Connected.
ati3
Manufacturer: Novatel Wireless Incorporated
Model: Expedite EU860D MiniCard
Revision: 10.10.04.01-01 [2007-04-11 14:07:19]
IMEI: 011186000228043
+GCAP: +CGSM,+DS,+ES
From: Nate Carlson <natecars@natecarlson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.
Cc: stable <stable@kernel.org>
Signed-off-by: Ed Beroset <beroset@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pl2303: add support for RATOC REX-USB60F
This patch adds support for RATOC REX-USB60F Serial Adapters,
which is widely used in Japan recently.
Cc: stable <stable@kernel.org>
Signed-off-by: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for Onda H600/Zte MF330 GPRS/UMTS/HSDPA datacard
Cc: stable <stable@kernel.org>
Signed-off-by: Bruno Redondi <bruno.redondi@altarisoluzione.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.
From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I work with a group of people on a free home automation tool called
FHEM. Some of the users own more than one USB-serial device by ELV. The
ftdi_sio driver has most of the ELV devices disabled by default and
needs to be re-enabled every time you get a new kernel. Additionally a
new device (EM 1010 PC - enegry monitor) is missing in the list.
Currently our users have to follow the instructions we provide at
http://www.koeniglich.de/fhem/linux.html ... However, to some users it
is too complicated to compile their own kernel module.
We are aware that you can specify one additional device using the
vendor/product option of the module. But lot's of users own more than
one device.
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Stark <peter.stark@t-online.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following improvements were made:
- Added new product support: MC5725, AC 880 U, MP 3G (UMTS & CDMA)
Cc: stable <stable@kernel.org>
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simply adds the "YC Cable" as a vendor and its pl2303-based
USB<->Serial adapter as a product. This particular adapter is sold by
Radio Shack. I've done limited testing on a few different systems with
no issues.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the appropriate vendor and device IDs for the AirCard 881U to
sierra.c. (This device is often rebadged by AT&T as the USBConnect 881).
Cc: stable <stable@kernel.org>
Signed-off-by: Jessica L Blank <j@twu.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB
without trying to ram its contents down the throat of an ex-tty.
Cc: stable <stable@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB without
trying to ram its contents down the throat of an ex-tty.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Cleaning out all the incorrect 'no change made' checks for termios
settings showed up a problem with the PL2303. The hardware here seems to
lose sync and bits if you tell it to make no changes. This shows up with
a real world application.
To fix this the driver check for meaningful hardware changes is restored
but doing the tests correctly and as a tty layer function so it doesn't
get duplicated wrongly everywhere if other drivers turn out to need it.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mirko Parthey <mirko.parthey@informatik.tu-chemnitz.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
attached please find a new device ID for CP2101 driver. This device is a
usb stick from Dynastream to communicate with ANT wireless devices which
I suppose is fairly similar to the ANT dev board having product id 0x1003.
From: Martin Kusserow <kusserow@ife.ee.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds VID/PID for the MC8775 found internally in the Thinkpad X61s laptop
(and likely others). For commercial reasons the driver maintainer cannot
add VID/PIDs for laptop OEM devices himself.
Signed-off-by: Kevin R Page <linux-kernel@krp.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102. I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.
From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a patch to fix the addition of the new product ids I sent.
It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(
Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert 7eea436433.
Lucy said:
This patch will work with the 19HS but WILL BREAK all other Keyspan
adapters. It will take me a few days to get to looking at a correct fix but
that keyspan_send_setup(port, 1) (and the '1' is the important part) must
happen once when the port is first opened. The cflag can just be set to
whatever the normal default is for your serial environment.
So revert this again pending the proper fix.
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Lucy McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per the maintainer of the usbserial/sierra.c driver, the patch below adds
a new id to the list of supported cards for the sierra driver. Tested and
working for me on Fedora 8, kernel 2.6.23 and on the more recent sierra.c
available in
http://www.sierrawireless.com/resources/support/Software/Linux/v.1.2.6b(kernel2.6.21).zip
Hardware is a MiniPCI card in a Lenovo T61p.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit acd2a847e7 usb_serial_generic_write()
disables interrupts when taking &port->lock which is also taken in
usb_serial_generic_read_bulk_callback() resulting in an inconsistent lock state
due to the latter not disabling interrupts on the local cpu. Fix that by
disabling interrupts in the latter call site also.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pl2303: add support for Corega CG-USBRS232R
This patch adds support for Corega CG-USBRS232R Serial Adapters.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove redundant code leading to NULL ptr deref and let terminal config
settings take place in the proper initialization path in
usb_console_setup().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: <lucy@keyspan.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB: usbserial - fix potential deadlock between write() and IRQ
usb_serial_generic_write() doesn't disable interrupts when taking port->lock,
and could therefore deadlock with usb_serial_generic_read_bulk_callback()
being called from interrupt, taking the same lock. Fix it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the IO Data Device USB-RSAQ5, PL2303 based
USB-serial converter, to pl2303 driver
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: line over 80 characters
#23: FILE: drivers/usb/serial/ftdi_sio.c:297:
+ speed_t force_baud; /* if non-zero, force the baud rate to this value */
ERROR: use tabs not spaces
#31: FILE: drivers/usb/serial/ftdi_sio.c:881:
+^I$
ERROR: use tabs not spaces
#39: FILE: drivers/usb/serial/ftdi_sio.c:890:
+^I$
WARNING: line over 80 characters
#111: FILE: drivers/usb/serial/ftdi_sio.c:1956:
+ tty_encode_baud_rate(port->tty, priv->force_baud, priv->force_baud);
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No hardware termios setting in this case so keep the old settings
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the devices that have no hardware settings set up the termios return
properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Clear unsupported CMSPAR bit
- Clean up long chains of a->b-> a bit
- Encode baud rate back into tty structure properly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Clean up paranoia checks
- Propogate back a correct fixed termios
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The empeg is pretty fixed. Tidy up the long foo->bar->baz stuff and
encode the fixed speed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Expand some x&y to x & y so I could read it when checking
- Clear CMSPAR bit in the termios (as the driver does not support it)
- Encode the speed using the new tty_encode_baud_rate facility
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>