Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
The patch contains Intel IOMMU IA64 specific code. It defines new
machvec dig_vtd, hooks for IOMMU, DMAR table detection, cache line flush
function, etc.
For a generic kernel with CONFIG_DMAR=y, if Intel IOMMU is detected,
dig_vtd is used for machinve vector. Otherwise, kernel falls back to
dig machine vector. Kernel parameter "machvec=dig" or "intel_iommu=off"
can be used to force kernel to boot dig machine vector.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that the following error message is sometimes displayed
at irq migration when vector domain is enabled.
"Unexpected interrupt vector %d on CPU %d is not mapped to any IRQ!"
The cause of this problem is an interrupt is sent to the previous
target CPU after cleaning up vector to irq mapping table. To clean up
vector to irq map on the previous target CPU safty, change the irq
migration in multiple vector domain as follows. The original idea is
from x86 interrupt management code.
- Delay vector to irq table cleanup until the interrupts are sent
to new target CPUs. By this, it is ensured that target CPU is
completely changed on the interrupt controller side.
- Even after the interrupts are sent to new target CPUs, there can
be pended interrupts remaining on the previous target CPU. So we
need to delay clearning up vector to irq table until the pended
interrupt is handled. For this, send IPI to the previous target
CPU with lower priority vector and clean up vector to irq table
in its handler.
This patch affects only to irq migration code with multiple vector
domain is enabled.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that pci_enable_msi() fails on ia64 platform. The cause of
this problem is incorrect return value of ia64_setup_msi_irq(). It must
return 0 on success, instead of irq number.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add support for IRQ migration across vector domain.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add fundamental support for multiple vector domain. There still exists
only one vector domain even with this patch. IRQ migration across
domain is not supported yet by this patch.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following 'if' statement in ia64_setup_msi_irq() always fails even
if create_irq() returns <0 value, because variable 'irq' is defined as
unsigned int. It would cause invalid memory access.
irq = create_irq();
if (irq < 0)
return irq;
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arch hooks arch_setup_msi_irq and arch_teardown_msi_irq are now
responsible for allocating and freeing the linux irq in addition to
setting up the the linux irq to work with the interrupt.
arch_setup_msi_irq now takes a pci_device and a msi_desc and returns
an irq.
With this change in place this code should be useable by all platforms
except those that won't let the OS touch the hardware like ppc RTAS.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is just a few makefile tweaks and some file renames.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
