Anomaly 05000312 - Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted:
DESCRIPTION:
When instruction cache is enabled, erroneous behavior may occur when any of the following instructions are interrupted:
. CSYNC
• SSYNC
• LCx =
• LTx = (only when LCx is non-zero)
• LBx = (only when LCx is non-zero)
When this problem occurs, a variety of incorrect things could happen, including an illegal instruction exception. Additional errors could
show up as an exception, a hardware error, or an instruction that is valid but different than the one that was expected.
WORKAROUND:
Place a cli before all SSYNC, CSYNC, "LCx =", "LTx =", and "LBx =" instructions to disable interrupts, and place an sti after each of these
instructions to re-enable interrupts. When these instructions are executed in code that is already non-interruptible, the problem will not
occur.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: Len Brown <len.brown@intel.com>
Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix RedHat bug 329431
The idea here is separate "conscious" from "unconscious" flushes.
Conscious flushes are those due to a fsync() or close(). Unconscious
ones are flushes that occur as a side effect of some other operation or
due to memory pressure.
Currently, when an error occurs during an unconscious flush (ENOSPC or
EIO), we toss out the page and don't preserve that error to report to
the user when a conscious flush occurs. If after the unconscious flush,
there are no more dirty pages for the inode, the conscious flush will
simply return success even though there were previous errors when writing
out pages. This can lead to data corruption.
The easiest way to reproduce this is to mount up a CIFS share that's
very close to being full or where the user is very close to quota. mv
a file to the share that's slightly larger than the quota allows. The
writes will all succeed (since they go to pagecache). The mv will do a
setattr to set the new file's attributes. This calls
filemap_write_and_wait,
which will return an error since all of the pages can't be written out.
Then later, when the flush and release ops occur, there are no more
dirty pages in pagecache for the file and those operations return 0. mv
then assumes that the file was written out correctly and deletes the
original.
CIFS already has a write_behind_rc variable where it stores the results
from earlier flushes, but that value is only reported in cifs_close.
Since the VFS ignores the return value from the release operation, this
isn't helpful. We should be reporting this error during the flush
operation.
This patch does the following:
1) changes cifs_fsync to use filemap_write_and_wait and cifs_flush and also
sync to check its return code. If it returns successful, they then check
the value of write_behind_rc to see if an earlier flush had reported any
errors. If so, they return that error and clear write_behind_rc.
2) sets write_behind_rc in a few other places where pages are written
out as a side effect of other operations and the code waits on them.
3) changes cifs_setattr to only call filemap_write_and_wait for
ATTR_SIZE changes.
4) makes cifs_writepages accurately distinguish between EIO and ENOSPC
errors when writing out pages.
Some simple testing indicates that the patch works as expected and that
it fixes the reproduceable known problem.
Acked-by: Dave Kleikamp <shaggy@austin.rr.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
USB support for the 8349itx got added a while back; but the defconfig
never got updated. This patch adds the appropriate USB config options
to the defconfigs
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Scott Wood <scottwood@freescale.com>
CC: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mmc_spi has hit the mainline, so we can start using it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Check value ranges in ctl callbacks properly. This fixes the unexpected
crash due to wrong value assignment.
Also, remove invalid comments in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the calculation of the private_data pointer in the CS4270 driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by Ingo Molnar,
when booting an allyesconfig bzImage kernel the bootup hangs in the
portman2x4 driver (on a box that does not have this hardware), at:
Pid: 1, comm: swapper
EIP: 0060:[<c02f763c>] CPU: 0
EIP is at parport_pc_read_status+0x4/0x8
EFLAGS: 00000202 Not tainted (2.6.23-rc9 #904)
EAX: f7e57a7f EBX: 00000010 ECX: c2b808c0 EDX: 00000379
ESI: f7cb8230 EDI: 00000010 EBP: f7cb8230 DS: 007b ES: 007b FS: 0000
CR0: 8005003b CR2: fff9c000 CR3: 007ec000 CR4: 00000690
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c04613de>] portman_flush_input+0xde/0x12c
[<c0461a24>] snd_portman_probe+0x368/0x484
[<c02fbb8c>] __device_attach+0x0/0x8
[<c02fce68>] platform_drv_probe+0xc/0x10
[<c02fba6c>] driver_probe_device+0x74/0x194
[<c0587174>] klist_next+0x38/0x70
[<c02fbb8c>] __device_attach+0x0/0x8
[<c02faea1>] bus_for_each_drv+0x35/0x68
[<c02fbc22>] device_attach+0x72/0x78
the reason is due to an inconsistent error return code of 1 or 2, while
snd_portman_probe only realizes negative error codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The driver assigns the write proc callback to read wrongly.
Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The Samsung S3C24xx uses new architecture file layout in the post 2.6.23
kernel. This patch fixes include path for the s3c2443-ac97.c.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Make sure all subchannel handling is done on the slow path workqueue
so that we don't have races between an old subchannel unregistering
and a new subchannel with the same name registering.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Before we're getting short on memory detection fixes here is the next
one: if neither sclp nor diag260 report the storage size the detection
loop will return immediately without detecting anything. Fix this by
breaking the detection loop only if the memory end is known.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The iucv is the only user of the various functions that are used to bring
parts of cpus up and down. Its the only allocpercpu user that will do
I/O on per cpu objects (which is difficult to do with virtually mapped memory).
And its the only use of allocpercpu where a GFP_DMA allocation is done.
Remove the allocpercpu calls from iucv and code the allocation and freeing
manually. After this patch it is possible to remove a large part of
the allocpercpu API.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't perform a sigp store-status-at-address on smp_send_stop().
It will overwrite the lowcores of other cpus and destroys valueable
debug informations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
page_mkclean used to call page_clear_dirty for every given page. This
is different to all other architectures, where the dirty bit in the
PTEs is only resetted, if page_mapping() returns a non-NULL pointer.
We can move the page_test_dirty/page_clear_dirty sequence into the
2nd if to avoid unnecessary iske/sske sequences, which are expensive.
This change also helps kvm for s390 as the host must transfer the
dirty bit into the guest status bits. By moving the page_clear_dirty
operation into the 2nd if, the vm will only call page_clear_dirty
for pages where it walks the mapping anyway. There it calls
ptep_clear_flush for writable ptes, so we can transfer the dirty bit
to the guest.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When returning from IRQ handling and TIF_NEED_RESCHED is set we must
call preempt_schedule_irq() instead of schedule().
Otherwise the BKL might be unlocked in schedule() and therfore
everything that relies on the BKL is broken.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove binary sysctls that never worked due to missing strategy functions.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove binary sysctls that never worked due to missing strategy functions.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current support for TRACE_IRQFLAGS and lockdep_sys_exit is broken.
IRQ flag tracing is broken for program checks. Even worse is that
the newly introduced calls to lockdep_sys_exit are in the critical
section code which is not supposed to call any C functions. In
addition the checks if locks are still held are also done when
returning to kernel code which is broken as well.
Fix all this by disabling interrupts and machine checks at the
exit paths and then do the appropriate checks and calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When doing an magic sysrq reboot on s390 the following bug message
appears:
SysRq : Resetting
BUG: sleeping function called from invalid context at include/asm/semaphore.h:61
in_atomic():1, irqs_disabled():0
07000000004002a8 000000000fe6bc48 0000000000000002 0000000000000000
000000000fe6bce8 000000000fe6bc60 000000000fe6bc60 000000000012a79a
0000000000000000 07000000004002a8 0000000000000006 0000000000000000
0000000000000000 000000000fe6bc48 000000000000000d 000000000fe6bcb8
00000000004000c8 0000000000103234 000000000fe6bc48 000000000fe6bc90
Call Trace:
(¬<00000000001031b2>| show_trace+0x12e/0x148)
¬<000000000011ffca>| __might_sleep+0x10a/0x118
¬<0000000000129fba>| acquire_console_sem+0x92/0xf4
¬<000000000012a2ca>| console_unblank+0xc2/0xc8
¬<0000000000107bb4>| machine_restart+0x54/0x6c
¬<000000000028e806>| sysrq_handle_reboot+0x26/0x30
¬<000000000028e52a>| __handle_sysrq+0xa6/0x180
¬<0000000000140134>| run_workqueue+0xcc/0x18c
¬<000000000014029a>| worker_thread+0xa6/0x108
¬<00000000001458e4>| kthread+0x64/0x9c
¬<0000000000106f0e>| kernel_thread_starter+0x6/0xc
¬<0000000000106f08>| kernel_thread_starter+0x0/0xc
The only reason for doing a console_unblank on s390 is to flush the
log buffer. We have to check for in_atomic before doing a
console_unblank as the console is otherwise filled with an unrelated
bug message.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Modify the sense id channel program to allow device sensing of pav
alias devices which belong to a base device with ungrouped paths.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
My changes to _tlbie to fix 4xx unfortunately broke 8xx build in a
couple of places. This fixes it.
Spotted by Olof Johansson.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interrupt map for the PCI PHB that had the ULI1575 was not correct
on the boards that have it.
* 8544 DS:
- Fix interrupt mask
- Be explicit about use of INTA for on chip peripherals
* 8572 DS/8641 HPCN:
- Fix interrupt mask
- Expand interrupt map for PCI slots to cover all functions
- Be explicit about use of INTA for on chip peripherals
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
