Calculate a score for each 1000 IRQs:
- TX completions are worth 1 point
- RX completions are worth 4 if merged using LRO or 2 otherwise
Reduce moderation if the score is less than 10000, down to a minimum
of 5 us. Increase moderation if the score is more than 20000, up to
the specified maximum.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug this function works around only applies to the first set of
page-mapped registers; other pages can be written without locking.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, reading the legacy interrupt status register can
acknowledge an event queue whose attention flag has not yet been set
in the register. Until we service this event queue it will not
generate any more interrupts. Therefore, as a secondary check, poll
the next slot in each active event queue whose flag is not set.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet parser used in the TX data path for locating checksum
fields can lose synchronisation with the TX queue manager when
handling packets that look like IPv4 but are too short (17-32 bytes).
Work around this by padding to 33 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error count a per-NIC variable.
Reset this the count after an hour if it has not reached the critical value.
Set the critical value back to 5.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flushing queues we disable normal interrupt and event handling and
poll event queue 0 looking for flush completions. Unfortunately the
flush event polling loop fails to move past any other type of event.
This problem has not been observed in production hardware but appears to
be a possibility.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_del_adapter() leaves dangling pointers in the structure. If we
retry the NIC probe and pass the structure to i2c_add_adapter() again
it will lead to an oops unless we clear it first.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MAC switching fails, stop the port properly.
If PHY reinitialisation fails, clear the port_initialized flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinitialise LEDs after overriding them for identification.
Rename set_fault_led method to set_id_led since we always use it for
NIC identification and not faults.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new PHY supporting SFP+ modules, used in the SFN4112F
reference design. It is similar to the QT2022C2 and shares much of
its support code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuffle bits of the OUI into the conventional written order.
Replace PHY id component macros with functions.
Zero-pad PHY id components in log messages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SFN4111T initialisation, check whether the PHY boot status
indicates a bad firmware checksum. If so, prepare to reflash rather
than continuing with normal initialisation.
Remove redundant PHY boot status check from tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 27dd2caca4 changed
mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and
to combine their values into an unsigned 32-bit mask. This made the
following test for a negative (failure) value useless. Fix it to
check whether either read failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Include the header file. If CONFIG_SFC_MTD is not defined
then the functions 'efx_mtd_remove' and 'efx_mtd_rename' are defined
'static inline' with an empty function body in the header file, but
the the whole file mtd.c is not built in this case.
Fix this sparse warnings:
drivers/net/sfc/mtd.c:204:6: warning: symbol 'efx_mtd_remove' was not declared. Should it be static?
drivers/net/sfc/mtd.c:221:6: warning: symbol 'efx_mtd_rename' was not declared. Should it be static?
drivers/net/sfc/mtd.c:230:5: warning: symbol 'efx_mtd_probe' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as close to their usage as possible.
Fix this sparse warning:
drivers/net/sfc/tenxpress.c:589:22: warning: symbol 'link_ok' shadows an earlier one
drivers/net/sfc/tenxpress.c:575:30: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/falcon.c: In function ‘falcon_alloc_special_buffer’:
drivers/net/sfc/falcon.c:340: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 10 has type ‘phys_addr_t’
drivers/net/sfc/falcon.c: In function ‘falcon_free_special_buffer’:
drivers/net/sfc/falcon.c:355: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 10 has type ‘phys_addr_t’
drivers/net/sfc/falcon.c: In function ‘falcon_probe_port’:
drivers/net/sfc/falcon.c:2346: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 7 has type ‘phys_addr_t’
drivers/net/sfc/falcon.c: In function ‘falcon_probe_nic’:
drivers/net/sfc/falcon.c:2924: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 7 has type ‘phys_addr_t’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset. This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is not specific to rev A.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the loopback mode, there may be no pertinent link state
bits. In this case we test the PHYXS RX fault bit instead. Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, set pause advertising bits properly.
A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before. This ensures that the value is
correct after an online reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.
Update comments to explain exactly what we're doing.
Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750). We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors. This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware. Therefore remove it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sfc invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
Everything should appear identical to the user except that the
offload is now controlled by the GRO ethtool option instead of
LRO. I've kept the lro module parameter as is since that's for
compatibility only.
I have eliminated efx_rx_mk_skb as the GRO layer can take care
of all packets regardless of whether GRO is enabled or not.
So the only case where we don't call GRO is if the packet checksum
is absent. This is to keep the behaviour changes of the patch to
a minimum.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: reduce stack usage, use new cpumask API.
Remove a cpumask from the stack. Ben Hutchings indicated that printing
a warning and returning 1 was acceptable for the corner case where allocation
fails.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: linux-net-drivers@solarflare.com
Impact: reduce stack usage, use new cpumask API.
This actually uses topology_core_cpumask() and
topology_thread_cpumask(), removing the only users of
topology_core_siblings() and topology_thread_siblings()
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: linux-net-drivers@solarflare.com
Only the SFX7101 requires software power control. This was
incorrectly being applied to the SFT9001 rev A as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_disable_device() disables many features, like MSI-X, which we
never reenable in efx_reset(). Further, calls to pci_enable_device()
and pci_disable_device() must be matched since the nesting count was
introduced, so switch to using pci_clear_master() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we removed the network device argument from several
NAPI interfaces in 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.")
several drivers now started getting unused variable warnings.
This fixes those up.
Signed-off-by: David S. Miller <davem@davemloft.net>
When AN is enabled and the link is down the speed/duplex control bits
will not be meaningful. Use the advertising bits instead, and mask
them with the LPA bits if and only if AN is complete (as before).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
