Modules: HDA Codec driver
Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
The following patch changes the initverbs associated with the output sum
widgets 0x08, 0x09 and 0x0a used with the fujitsu model in patch_realtek.c.
It is against alsa 1.0.11rc3.
Currently these widgets have their output muted, but a close reading of the
datasheet suggests that they don't actually have an output mute. They have
an *input* mute for each of their two inputs and a single output gain. This
patch therefore activates the input mutes and zeros the output gain. It has
not yet been tested but the above interpretation of the ALC260 datasheet
seems correct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
The following patch against alsa 1.0.11rc3 creates a PCM device (pcm1c) for
the second ADC present on the ALC260 codec used by the hda driver. It also
defines a new mixer control allowing the mode of retasking pins to be set;
this means a user can (for example) designate the headphone jack to be a
second input. With this patch in place it is possible to do 4 channel
recording on laptops equipped with an ALC260 codec assuming both a stereo
line-in jack is provided in addition to a headphone jack.
Mixer controls are provided to allow the headphone jack to be switched as
an input. In addition, an (input only) mode control is configured for
the line-in jack to allow a bias voltage to be requested (VREF80 or VREF50)
so headsets based on condensor microphones have a chance of working.
This patch has been tested on a Fujitsu S7020 laptop and as such these
features are currently only configured for the 'fujitsu' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec
Added the support of static resolution table support for codecs
that the driver cannot probe the volume resolution properly.
The table pointer should be set in each codec patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
- added 0x107d:0x6606 to whitelist
- print also the pci device ID for developers when model is not known
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: ICE1712 driver
Change the value written to hardware configuration register of envy24 chip
in the case of Terratec DMX6fire to restrict the active ADCs & DACs to 6.
Also add the dxr_enable module option to eventually leave the old behaviour
when user requests.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
Fix the driver codes to run on 64bit architectures.
The patch taken from ALSA BTS bug#1047.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).
We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Documentation,HDA Intel driver
Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
Fix the detection of tertriary codec on SIS7012, including clean-ups
of relevant codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This little patch add the model for the motherboard K8N51 from Gigabyte
to the known models of ALC boards.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
* Fix init sequence so manually retaskable jacks don't get added to
the line_out list.
* Update intel mobo config defaults to specify surround outputs
as line outs rather than speakers.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Fix max_channels computation for STAC92xx codecs in the case only
HP pin without line-out pins is detected in the default pin config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This adds support for Agere's variant of Si3054/5 based HDA modem.
Signed-off-by: Sasha Khapyorsky <sashak@alsa-project.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Digigram PCXHR driver
sound/pci/pcxhr/pcxhr.c: In function 'pcxhr_update_r_buffer':
sound/pci/pcxhr/pcxhr.c:460: warning: unsigned int format, different type arg (arg 7)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: RME9652 driver
sound/pci/rme9652/hdspm.c: In function 'snd_hdspm_preallocate_memory':
sound/pci/rme9652/hdspm.c:3327: warning: int format, different type arg (arg 4)
sound/pci/rme9652/hdspm.c:3331: warning: int format, different type arg (arg 4)
sound/pci/rme9652/hdspm.c: In function 'snd_hdspm_create':
sound/pci/rme9652/hdspm.c:3513: warning: int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
This patch adds a quirk entry for the Dell Optiplex GX270, on which
the volume is set by the headphone control, not the master control.
Signed-off-by: Chris Ball <cjb@mrao.cam.ac.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALI5451 driver
This patch uses #defines for the Vendor ID and Device ID and uses the
new PCI_DEVICE macro.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Trident driver
Some pcnet32 hardware erroneously has the Vendor ID for Trident. The
pcnet32 driver looks for the PCI ethernet class before grabbing the
hardware, but the current trident driver does not check against the
PCI audio class. This allows the trident driver to claim the pcnet32
hardware. This patch prevents that.
Per Jiri Slaby's request, I changed the trident driver to use
PCI_DEVICE macro and PCI ID #defines.
This patch is untested on Trident 4DWAVE_DX hardware, but has been
tested on pcnet32 hardware.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
Set the (read only) sample rate field in the IEC958 mixer controls to
48 kHz (instead of 44.1 kHz) because that is the rate actually
supported by the hardware.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: AC97 Codec
Added a blacklist to suppress to create jack sense controls.
These controls must be always off on some devices (e.g. Thinkpad).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Intel driver
This patch adds the Intel ICH8 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
The patch siply adds the PCI IDs of AVerMedia Studio No. 103, 203,
and possibly even other versions with the same PCI IDs to the snd-bt87x
driver and sets its default sampling rate to 48 kHz.
Signed-off-by: Martin Drab <drab@kepler.fjfi.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
