Doing min_t(int, foo, INT_MAX) doesn't work correctly, because if foo
is bigger than INT_MAX, then when treated as a signed integer, it will
become negative and hence such an expression is just an elaborate NOP.
Fix such cases in ehca to do min_t(unsigned, foo, INT_MAX) instead.
This fixes negative reported values for max_cqe, max_pd and max_ah:
Before:
max_cqe: -64
max_pd: -1
max_ah: -1
After:
max_cqe: 2147483647
max_pd: 2147483647
max_ah: 2147483647
Based on a bug report and fix from Anton Blanchard <anton@samba.org>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix ehca SRQ support so that IPoIB connected mode works:
- Report max_srq > 0 if SRQ is supported
- Report "last wqe reached" asynchronous event when base QP dies;
this is required by the IB spec and IPoIB CM relies on receiving it
when cleaning up.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Run the existing ehca code through checkpatch.pl and clean up the
worst of the coding style violations.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When firmware reports a nondisruptive port configuration change event,
previous versions of the eHCA driver didn't forward the event to consumers
like IPoIB. Add code that determines the type of configuration change by
comparing old and new port attributes and reports it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for support of new eHCA2 features, change adapter probing:
- Hardware level is changed to encode major and minor chip version
- Hardware capabilities are queried from the firmware
- The maximum MTU is queried from the firmware instead of assuming a
fixed value
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "Modify Port" verb support to eHCA driver. The IB communication
manager needs this to set the IsCM port capability bit when
initializing.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the port phys state as returned from ehca_query_port() to LINK_UP.
ehca actually represents a logical HCA, whose phys/link state always
is LINK_UP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Here is a patch for ehca to use proper flag, ie. GFP_ATOMIC
resp. GFP_KERNEL, when calling get_zeroed_page() to prevent "Bug:
scheduling while atomic...". This error does not cause a kernel panic
but makes ipoib un-usable afterwards. It is reproducible on
2.6.20-rc4 if one does ifconfig down during a flood ping test. I have
not observed this error in earlier releases incl. 2.6.20-rc1.
This error occurs when a qp event/irq is received and ehca event
handler allocates a control block/page to obtain HCA error data block.
Use of GFP_ATOMIC when in interrupt context prevents this issue.
Signed-off-by Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Assure 4K alignment for firmware control blocks in 64K page mode,
because kzalloc()'s result address might not be 4K aligned if 64K
pages are enabled. Thus, we introduce wrappers called
ehca_{alloc,free}_fw_ctrlblock(), which use a slab cache for objects
with 4K length and 4K alignment in order to alloc/free firmware
control blocks in 64K page mode. In 4K page mode those wrappers just
are defines of get_zeroed_page() and free_page().
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a driver for IBM GX bus InfiniBand adapters, which are usable with
some pSeries/System p systems.
Signed-off-by: Heiko J Schick <schickhj.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
