Testing GTT ready might be more correct but cp.ready
works fine and has been tested on irc by 2-3 ppl.
fixes bug k.org 15035 and fd.o 25733
Signed-off-by: Dave Airlie <airlied@redhat.com>
Due to heat issues. Fixes fdo bug 25992
v2: fix typo noticed by Maarten Maathuis
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unhandled vectors can be safely ignored, no need
to spam the kernel log by default.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on radeonfb code and recent ddx fix.
v2: minor formatting fix from Michel Dänzer
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Tested-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we setup buffer for display plane, we'll check any pending
required GPU flush and possible make interruptible wait for flush
complete. But that wait would be most possibly to fail in case of
signals received for X process, which will then fail modeset process
and put display engine in unconsistent state. The result could be
blank screen or CPU hang, and DDX driver would always turn on outputs
DPMS after whatever modeset fails or not.
So this one creates new helper for setup display plane buffer, and
when needing flush using uninterruptible wait for that.
This one should fix bug like https://bugs.freedesktop.org/show_bug.cgi?id=24009.
Also fixing mode switch stress test on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There exist multiple DDC buses for the SDVO cards with multiple outputs.
When we can't get the EDID by using the select DDC bus, we can try the other
possible DDC bus to see whether the EDID can be obtained.
https://bugs.freedesktop.org/show_bug.cgi?id=23842
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some SDVO cards based on conexant chip, we can't read the EDID if
we don't read the response after issuing SDVO DDC bus switch
command.
From the SDVO spec once when another I2C transaction is finished after
completing the I2C transaction of issuing the bus switch command, it
will be switched back to the SDVO internal state again. So we can't
initiate a new I2C transaction to read the response after issuing the
DDC bus switch command. Instead we should issue DDC bus switch command
and read the response in the same I2C transaction.
https://bugs.freedesktop.org/show_bug.cgi?id=23842https://bugs.freedesktop.org/show_bug.cgi?id=24458https://bugs.freedesktop.org/show_bug.cgi?id=24522https://bugs.freedesktop.org/show_bug.cgi?id=24282
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some boxes the BIOS will report different child device arrays when
the system is booted with/without the dock. In such case the HDMI/DP
port can't be setup correctly. So revert two commits
(fc816655236cd9da162356e96e74c7cfb0834d92/
6e36595a21) that use the child device
parsed from VBT to setup HDMI/DP.
http://bugzilla.kernel.org/show_bug.cgi?id=14854http://bugzilla.kernel.org/show_bug.cgi?id=14860
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sean Young <sean@mess.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915), among other things, removed the .suspend and
.resume pointers from the struct drm_driver object in i915_drv.c,
which broke resume without KMS on my MSI Wind U100.
Fix this by reverting that part of commit cbda12d77e.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: added comment explaining when .suspend/.resume matter]
Signed-off-by: Eric Anholt <eric@anholt.net>
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 871af1210f enabled 32bit PIO for
PATA piix but didn't for SATA. There's no reason not to use 32bit PIO
on SATA piix. Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.
Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.
This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.
This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for. Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Input core displays capabilities bitmasks in form of one or more longs printed
in hex form and separated by spaces. Unfortunately it does not work well
for 32-bit applications running on 64-bit kernels since applications expect
that number is "worth" only 32 bits when kernel advances by 64 bits.
Fix that by ensuring that output produced for compat tasks uses 32-bit units.
Reported-and-tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It moves to the same directory as the boot files in other formats.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With typical mult and shift values, the calculation for Octeon's sched_clock
overflows when using 64-bit arithmetic. Use 128-bit calculations instead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/849/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A call to r4k_clocksource_init() was added to plat_time_init(), but
when init_mips_clock_source() calls the same function, boot fails in
clockevents_register_device(). This patch removes the extraneous call.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Patchwork: http://patchwork.linux-mips.org/patch/803/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the advent of function graph tracing on MIPS, Octeon needs a high
precision sched_clock() implementation. Without it, most timing
numbers are reported as 0.000.
This new sched_clock just uses the 64-bit cycle counter appropriately
scaled.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 898d357b5262f9e26bc2418e01f8676e80d9867e (lmo) /
6acc7d485c (kernel.org) ("Fix and enhance
built-in kernel command line") arcs_cmdline[] does not contain built-in
command line. The commit introduce CONFIG_CMDLINE_BOOL and
CONFIG_CMDLINE_OVERRIDE to control built-in command line, and now we can
use them instead of platform-specific built-in command line processing.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Patchwork: http://patchwork.linux-mips.org/patch/802/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips_machine_halt() is same as mips_machine_restart(). Also delete the
registration of _machine_halt and pm_power_off because mips_machine_halt()
is the restart function.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/798/
Reviewed-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An unused leftover from the old KGDB implementation.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/794/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
sizeof(dp) is just the size of the pointer. Change it to the size of the
referenced structure.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Patchwork: http://patchwork.linux-mips.org/patch/789/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Remove the .initrd section. The initrd section was already handled
when vmlinux was linked.
o Discard .MIPS.options, .options, .pdr, .reginfo, .comment and .note
sections. If .MIPS.options is not removed, kernels compiled with gcc
3.4.6 will not boot.
o Clean up the file format.
o Remove several other unneeded sections.
Tested with GCC 3.4.6 and 4.4.1 with and without initrd.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/785/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The capture source or input source mixer element wasn't created properly
for ALC861-VD codec due to the wrong NID passed to
alc_auto_create_input_ctls().
References: Novell bnc#568305
http://bugzilla.novell.com/show_bug.cgi?id=568305
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
During TX timeout procedure dev could be awoken too early, e.g. by
sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame()
can run while buffers are freed causing an oops. This patch fixes it
by adding netif_device_present() test in sky2_tx_complete().
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925
With debugging by: Mike McCormack <mikem@ring3k.org>
Reported-by: Berck E. Nash <flyboy@gmail.com>
Tested-by: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the panel's probe had failed, omapfb would still go on, eventually
crashing.
A better fix would be to handle each display properly, and leaving just
the failed display out. But that is a bigger change.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Let the arch argument be overruled by bits. Otherwise, building of
external modules against a i386 target on a x86-64 host (and likely vice
versa as well) fails unless ARCH=i386 is explicitly passed to make.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
LKML-Reference: <4B4AFE10.8050109@siemens.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Revert commit 2fbd07a5f5, as this commit
breaks an IBM platform with quad-core Xeon cpu's.
According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).
Revert this for now because of the IBM platform breakage.
Another version will be re-submitted after the complete analysis.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_CFG80211_WEXT is not set, there is
a refcount imbalance with rdev->opencount, fix
that by moving it out of the ifdef.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_monitor_select_queue encounters data frames, it selects
the WMM AC based on skb->priority and assumes that skb->priority
contains a valid 802.1d tag. However this assumption is incorrect, since
ieee80211_select_queue has not been called at this point.
If skb->priority > 7, an array overrun occurs, which could lead to
invalid values, resulting in crashes in the tx path.
Fix this by setting skb->priority based on the 802.11 header for QoS
frames and using the default AC for all non-QoS frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3c509 was changed to support ethtool in 2002, making the 'xcvr' module
parameter obsolete in most cases. More recently 3c509 was converted
to the modern driver model and this parameter was removed. Fix the
documentation to refer to ethtool rather than the module parameter.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
