Almost entirely taken from the 64-bit PowerPC PCI code.
This allowed to eliminate a ton of cruft from the sparc64
PCI layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is kind of hokey, we could use the hardware provided facilities
much better.
MSIs are assosciated with MSI Queues. MSI Queues generate interrupts
when any MSI assosciated with it is signalled. This suggests a
two-tiered IRQ dispatch scheme:
MSI Queue interrupt --> queue interrupt handler
MSI dispatch --> driver interrupt handler
But we just get one-level under Linux currently. What I'd like to do
is possibly stick the IRQ actions into a per-MSI-Queue data structure,
and dispatch them form there, but the generic IRQ layer doesn't
provide a way to do that right now.
So, the current kludge is to "ACK" the interrupt by processing the
MSI Queue data structures and ACK'ing them, then we run the actual
handler like normal.
We are wasting a lot of useful information, for example the MSI data
and address are provided with ever MSI, as well as a system tick if
available. If we could pass this into the IRQ handler it could help
with certain things, in particular for PCI-Express error messages.
The MSI entries on sparc64 also tell you exactly which bus/device/fn
sent the MSI, which would be great for error handling when no
registered IRQ handler can service the interrupt.
We override the disable/enable IRQ chip methods in sun4v_msi, so we
have to call {mask,unmask}_msi_irq() directly from there. This is
another ugly wart.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do IRQ determination generically by parsing the PROM properties,
and using IRQ controller drivers for final resolution.
One immediate positive effect is that all of the IRQ frobbing
in the EBUS, ISA, and PCI controller layers has been eliminated.
We just look up the of_device and use the properly computed
value.
The PCI controller irq_build() routines are gone and no longer
used. Unfortunately sbus_build_irq() has to remain as there is
a direct reference to this in the sunzilog driver. That can be
killed off once the sparc32 side of this is written and the
sunzilog driver is transformed into an "of" bus driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Totally unused.
We need to traverse the list of global IRQ translaters,
so storing it in the per-bus structures was useless.
Signed-off-by: David S. Miller <davem@davemloft.net>
One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add assembler file for PCI hypervisor calls.
Setup basic skeleton of SUN4V PCI controller driver.
Add 32-bit devhandle to PBM struct, as this is needed for
hypervisor calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hairy fast allocator in the sparc64 PCI IOMMU code
has a hard limit of 256 pages. Certain devices can
exceed this when performing very large I/Os.
So replace with a more simple allocator, based largely
upon the arch/ppc64/kernel/iommu.c code.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the PCI controller drivers were doing the same thing
setting up the IOMMU software state, put it all in one spot.
Signed-off-by: David S. Miller <davem@davemloft.net>
This was the main impetus behind adding the PCI IRQ shim.
In order to properly order DMA writes wrt. interrupts, you have to
write to a PCI controller register, then poll for that bit clearing.
There is one bit for each interrupt source, and setting this register
bit tells Tomatillo to drain all pending DMA from that device.
Furthermore, Tomatillo's with revision less than 4 require us to do a
block store due to some memory transaction ordering issues it has on
JBUS.
Signed-off-by: David S. Miller <davem@davemloft.net>
Firstly, if the direction is TODEVICE, then dirty data in the
streaming cache is impossible so we can elide the flush-flag
synchronization in that case.
Next, the context allocator is broken. It is highly likely
that contexts get used multiple times for different dma
mappings, which confuses the strbuf flushing code and makes
it run inefficiently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
