This patch is based on the DMA-patch by Chip Coldwell for the AT91/AT32 serial
USARTS, with some tweaks to make it apply neatly on top of the other patches
in this series.
The RX and TX code has been moved to a tasklet and reworked a bit. Instead of
depending on the ENDRX and TIMEOUT bits in CSR, we simply grab as much data as
we can from the DMA buffers. I think this closes a race where the ENDRX bit
is set after we read CSR but before we read RPR, although I haven't confirmed
this.
Similarly, the two TX handlers (ENDTX and TXBUFE) have been combined into one.
Since the current code only uses a single TX buffer, there's no point in
handling those interrupts separately.
This also fixes a DMA sync bug in the original patch.
[linux@bohmer.net: rebased onto irq-splitup patch]
[hskinnemoen@atmel.com: moved to tasklet, fixed dma bug, misc cleanups]
[hskinnemoen@atmel.com: atmel_serial dma: Misc fixes and cleanups]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat the Kconfig entries and update descriptions for accuracy. Select the
driver by default for configurations of interest. For the curious: 32BIT
means only 32-bit DECstations support the device, not that the driver is not
64-bit clean; I have not checked that either though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add 512x support using the psc_ops framework established
with the previous patch.
All 512x PSCs share the same interrupt so add
IRQF_SHARED to irq flags.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
New serial driver for SC2681/SC2691 uarts. Older SNI RM400 machines are
using these chips for onboard serial ports.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Torben Mathiasen <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use SGI_HAS_ZILOG for IP22_ZILOG depends
- remove IP22 from description, because the driver works on more than
IP22 SGI machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for new ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add file ucc_uart.c, a serial device driver for the Freescale QUICCEngine.
Update the Kconfig and Makefile accordingly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This adds the option for the pmac_zilog driver to use the major/minor
numbers recently allocated specifically for it (/dev/ttyPZn) instead
of the /dev/ttySn numbers. The advantage of doing this is that it
allows the pmac_zilog and 8250 drivers to coexist. The disadvantage
of doing this is that it is a user-visible ABI change and it will
break existing working setups on powermacs, and could be confusing to
users.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SERIAL_BFIN=m or SERIAL_MUX=m shouldn't allow SERIAL_CORE_CONSOLE=y.
Additionally, this patch fixes whitespace instead of tabs at the
SERIAL_MUX_CONSOLE option.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial console can select only SERIAL_VR41XX=y.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7e92b4fc34. It broke Sébastien Dugué's
machine and Jeff said (persuasively)
This seems like it will break decades-long-working stuff, in favor of
breaking new ground in our favorite area, "trusting the BIOS."
It's just not worth it for serial ports, IMO. Serial ports are something
that just shouldn't break at this late stage in the game. My new Intel
platform boxes don't even have serial ports, so I question the value of
messing with serial port probing even more... because... just wait a year,
and your box won't have a serial port either! :)
I certainly don't object to the use of platform devices (or isa_driver),
but the probe change seems questionable. That's sorta analagous to
rewriting the floppy driver probe routine. Sure you could do it... but why
risk all that damage and go through debugging all over again?
It seems clear from this report that we cannot, should not, trust BIOS for
something (a) so simple and (b) that has been working for over a decade.
Much discussion ensued and we've decided to have another go at all of this.
Cc: Sébastien Dugué <sebastien.dugue@bull.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a reimplementation of the zs driver for the serial subsystem. Any
resemblance to the old driver is purely coincidential. ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...
Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.
This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A driver for the KS8695 internal UART.
Based on the 2.6.9 driver from Micrel.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make x86 COM ports into platform devices and don't probe for them
if we have PNP.
This prevents double discovery, where a device was found both by
the legacy probe and by 8250_pnp, e.g.,
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
This also means IRDA devices without a UART PNP ID will no longer be
claimed by the serial driver, which might require changes in IRDA
drivers and administration.
In addition to this patch, you may need to configure a setserial init
script, e.g., /etc/init.d/setserial, so it doesn't poke legacy UART
stuff back in. On Debian, "dpkg-reconfigure setserial" with the "kernel"
option does this.
To force the old legacy probe behavior even when we have PNPBIOS or
ACPI, load the new legacy_serial module (or build 8250 static) with
the "legacy_serial.force" option.
[akpm@linux-foundation.org: fix makefiles]
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Keith Owens <kaos@ocs.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Russell King <rmk+serial@arm.linux.org.uk>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements the driver necessary use the Analog Devices Blackfin
processor's Serial Port.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the serial_txx9 driver.
* Configurable manumum port number. (SERIAL_TXX9_NR_UARTS)
* Remove some code which is unneeded if CONFIG_PM=n.
* Use PCI_DEVICE() for pci device id table and make it const.
* Do not include <asm/irq.h>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Refactor Kconfig content to maximize nesting of menus by menuconfig and
xconfig.
Tested by simultaneously running `make xconfig` with and without
patch, and comparing displays.
Signed-off-by: Don Mullis <dwm@meer.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is on our "Envoy" boxes which we have, according to the documentation, an
"Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two
other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two
Exar UARTs. The last two Exar UARTs were not showing up and neither was the
modem.
This patch was the only way I could the kernel to see beyond the standard four
serial ports and get all four of the Exar UARTs to show up.
[akpm@osdl.org: build fix]
Signed-off-by: Paul B Schroeder <pschroeder@uplogix.com>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a driver for the Xilinx uartlite serial controller used in boards with
the PPC405 core in the Xilinx V2P/V4 fpgas.
The hardware is very simple (baudrate/start/stopbits fixed and no break
support). See the datasheet for details:
http://www.xilinx.com/bvdocs/ipcenter/data_sheet/opb_uartlite.pdf
See http://thread.gmane.org/gmane.linux.serial/1237/ for the email thread.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix typo (repeated) in serial Kconfig.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the Kconfig entry for console on AMBA PL011 to match the code.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sh-sci needs to be able to define its number of ports to
support, we do this with a config option, like most other
ports do.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Patch from Ben Dooks
Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[ARM] 3600/1: increase amba-pl010 UART_NR to 8
[ARM] 3571/1: netX: serial driver for Hilscher netX
Patch from Andrew Victor
This patch includes a number of updates to the AT91RM9200 serial driver.
Changes include:
1. Conversion to a platform_driver. [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91. This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support. [David Brownell]
There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the serial driver for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the 8250 probe modules to be disabled if we're building for
with EMBEDDED enabled. This reduces the kernel size by not including
unnecessary probe module support.
Original idea from Matt Mackall for PCI only, expanded to others by
rmk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
