Masking oneshot edge type interrupts is wrong as we might lose an
interrupt which is issued when the threaded handler is handling the
device. We can keep the irq unmasked safely as with edge type
interrupts there is no danger of interrupt floods. If the threaded
handler has not yet finished then IRQTF_RUNTHREAD is set which will
keep the handler thread active.
Debugged and verified in preempt-rt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.
Move the wakeup after the action is installed and action->irq has been
set.
Reported-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Interrupt chips which are behind a slow bus (i2c, spi ...) and
demultiplex other interrupt sources need to run their interrupt
handler in a thread.
The demultiplexed interrupt handlers need to run in thread context as
well and need to finish before the demux handler thread can reenable
the interrupt line. So the easiest way is to run the sub device
handlers in the context of the demultiplexing handler thread.
To avoid that a separate thread is created for the subdevices the
function set_nested_irq_thread() is provided which sets the
IRQ_NESTED_THREAD flag in the interrupt descriptor.
A driver which calls request_threaded_irq() must not be aware of the
fact that the threaded handler is called in the context of the
demultiplexing handler thread. The setup code checks the
IRQ_NESTED_THREAD flag which was set from the irq chip setup code and
does not setup a separate thread for the interrupt. The primary
function which is provided by the device driver is replaced by an
internal dummy function which warns when it is called.
For the demultiplexing handler a helper function handle_nested_irq()
is provided which calls the demux interrupt thread function in the
context of the caller and does the proper interrupt accounting and
takes the interrupt disabled status of the demultiplexed subdevice
into account.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The
bus access needs to sleep and therefor cannot be called in atomic
contexts.
Some of the generic interrupt management functions like disable_irq(),
enable_irq() ... call interrupt chip functions with the irq_desc->lock
held and interrupts disabled. This does not work for such devices.
Provide a separate synchronization mechanism for such interrupt
chips. The irq_chip structure is extended by two optional functions
(bus_lock and bus_sync_and_unlock).
The idea is to serialize the bus access for those operations in the
core code so that drivers which are behind that bus operated interrupt
controller do not have to worry about it and just can use the normal
interfaces. To achieve this we add two function pointers to the
irq_chip: bus_lock and bus_sync_unlock.
bus_lock() is called to serialize access to the interrupt controller
bus.
Now the core code can issue chip->mask/unmask ... commands without
changing the fast path code at all. The chip implementation merily
stores that information in a chip private data structure and
returns. No bus interaction as these functions are called from atomic
context.
After that bus_sync_unlock() is called outside the atomic context. Now
the chip implementation issues the bus commands, waits for completion
and unlocks the interrupt controller bus.
The irq_chip implementation as pseudo code:
struct irq_chip_data {
struct mutex mutex;
unsigned int irq_offset;
unsigned long mask;
unsigned long mask_status;
}
static void bus_lock(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
mutex_lock(&data->mutex);
}
static void mask(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
irq -= data->irq_offset;
data->mask |= (1 << irq);
}
static void unmask(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
irq -= data->irq_offset;
data->mask &= ~(1 << irq);
}
static void bus_sync_unlock(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
if (data->mask != data->mask_status) {
do_bus_magic_to_set_mask(data->mask);
data->mask_status = data->mask;
}
mutex_unlock(&data->mutex);
}
The device drivers can use request_threaded_irq, free_irq, disable_irq
and enable_irq as usual with the only restriction that the calls need
to come from non atomic context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
For threaded interrupt handlers we expect the hard interrupt handler
part to mask the interrupt on the originating device. The interrupt
line itself is reenabled after the hard interrupt handler has
executed.
This requires access to the originating device from hard interrupt
context which is not always possible. There are devices which can only
be accessed via a bus (i2c, spi, ...). The bus access requires thread
context. For such devices we need to keep the interrupt line masked
until the threaded handler has executed.
Add a new flag IRQF_ONESHOT which allows drivers to request that the
interrupt is not unmasked after the hard interrupt context handler has
been executed and the thread has been woken. The interrupt line is
unmasked after the thread handler function has been executed.
Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms.
For oneshot interrupts the primary handler simply returns
IRQ_WAKE_THREAD and does nothing else. A generic implementation
irq_default_primary_handler() is provided to avoid useless copies all
over the place. It is automatically installed when
request_threaded_irq() is called with handler=NULL and
thread_fn!=NULL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
free_irq() can remove an irqaction while the corresponding interrupt
is in progress, but free_irq() sets action->thread to NULL
unconditionally, which might lead to a NULL pointer dereference in
handle_IRQ_event() when the hard interrupt context tries to wake up
the handler thread.
Prevent this by moving the thread stop after synchronize_irq(). No
need to set action->thread to NULL either as action is going to be
freed anyway.
This fixes a boot crash reported against preempt-rt which uses the
mainline irq threads code to implement full irq threading.
[ tglx: removed local irqthread variable ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This takes care of the following entry from Dan's list:
kernel/irq/resend.c +73 check_irq_resend(17) warning: variable derefenced before check 'desc->chip'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <200908062146.03638.bzolnier@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't move it if target node is -1.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4A785B5D.4070702@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since genirq: Delegate irq affinity setting to the irq thread
(591d2fb02e) compilation with
CONFIG_SMP=n fails with following error:
/usr/src/linux-2.6/kernel/irq/manage.c:
In function 'irq_thread_check_affinity':
/usr/src/linux-2.6/kernel/irq/manage.c:475:
error: 'struct irq_desc' has no member named 'affinity'
make[4]: *** [kernel/irq/manage.o] Error 1
That commit adds a new function irq_thread_check_affinity() which
uses struct irq_desc.affinity which is only available for CONFIG_SMP=y.
Move that function under #ifdef CONFIG_SMP.
[ tglx@brownpaperbag: compile and boot tested on UP and SMP ]
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
LKML-Reference: <20090722222232.2eb3e1c4@neptune.home>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_set_thread_affinity() calls set_cpus_allowed_ptr() which might
sleep, but irq_set_thread_affinity() is called with desc->lock held
and can be called from hard interrupt context as well. The code has
another bug as it does not hold a ref on the task struct as required
by set_cpus_allowed_ptr().
Just set the IRQTF_AFFINITY bit in action->thread_flags. The next time
the thread runs it migrates itself. Solves all of the above problems
nicely.
Add kerneldoc to irq_set_thread_affinity() while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
The kerneldoc comment describing suspend_device_irqs() is currently
misleading, because generally the function doesn't really disable
interrupt lines at the chip level. Replace it with a more accurate
one.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
LKML-Reference: <200907050022.35117.rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq, irq.h: Fix kernel-doc warnings
genirq: fix comment to say IRQ_WAKE_THREAD
Don't hardcode to node zero for early boot IRQ setup memory allocations.
[ penberg@cs.helsinki.fi: minor cleanups ]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
Presently non-legacy IRQs have their irq_desc allocated with
kzalloc_node(). This assumes that all callers of irq_to_desc_node_alloc()
will be sufficiently late in the boot process that kmalloc is available.
While porting sparseirq support to sh this blew up immediately, as at the
time that we register the CPU's interrupt vector map only bootmem is
available. Check slab_is_available() to work out which path to use.
[ Impact: fix SH early boot crash with sparseirq enabled ]
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
LKML-Reference: <20090522014008.GA2806@linux-sh.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Trying to implement a driver to use threaded irqs, I was confused when the
return value to use that was described in the comment above
request_threaded_irq was not defined.
Turns out that the enum is IRQ_WAKE_THREAD where as the comment said
IRQ_THREAD_WAKE.
[Impact: do not confuse developers with wrong comments ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <alpine.DEB.2.00.0905121431020.13338@gandalf.stny.rr.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_irq_desc() will try to move irq_desc to the home node if
the allocated one is not correct, in create_irq_nr().
( This can happen on devices that are on different nodes that
are using MSI, when drivers are loaded and unloaded randomly. )
v2: fix non-smp build
v3: add NUMA_IRQ_DESC to eliminate #ifdefs
[ Impact: improve irq descriptor locality on NUMA systems ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F95EAE.2050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 044d408409.
The commit added a warning when handle_IRQ_event() is called outside
of hard interrupt context. This breaks the generic tasklet based
interrupt resend mechanism which is used when the hardware has no way
to retrigger the interrupt. So we get a warning for a use case which
is correct and worked for years. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
"tracing: create automated trace defines" causes this compile error on s390,
as reported by Sachin Sant against linux-next:
kernel/built-in.o: In function `__do_softirq':
(.text+0x1c680): undefined reference to `__tracepoint_softirq_entry'
This happens because the definitions of the softirq tracepoints were moved
from kernel/softirq.c to kernel/irq/handle.c. Since s390 doesn't support
generic hardirqs handle.c doesn't get compiled and the definitions are
missing.
So move the tracepoints to softirq.c again.
[ Impact: fix build failure on s390 ]
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
LKML-Reference: <20090429135139.5fac79b8@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.
v2: keep move_irq_desc related
[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
irq_set_affinity() and move_masked_irq() try to assign affinity
before calling chip set_affinity(). Some archs are assigning it
in ->set_affinity() again.
We do something like:
cpumask_cpy(desc->affinity, mask);
desc->chip->set_affinity(mask);
But in the failure path, affinity should not be touched - otherwise
we'll end up with a different affinity mask despite the failure to
migrate the IRQ.
So try to update the afffinity only if set_affinity returns with 0.
Also call irq_set_thread_affinity accordingly.
v2: update after "irq, x86: Remove IRQ_DISABLED check in process context IRQ move"
v3: according to Ingo, change set_affinity() in irq_chip should return int.
v4: update comments by removing moving irq_desc code.
[ Impact: fix /proc/irq/*/smp_affinity setting corner case bug ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F65509.60307@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The original feature of migrating irq_desc dynamic was too fragile
and was causing problems: it caused crashes on systems with lots of
cards with MSI-X when user-space irq-balancer was enabled.
We now have new patches that create irq_desc according to device
numa node. This patch removes the leftover bits of the dynamic balancer.
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F654AF.8000808@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CPUMASKS_OFFSTACK is not defined anywhere (it is CPUMASK_OFFSTACK).
It is a typo and init_allocate_desc_masks() is called before it set
affinity to all cpus...
Split init_alloc_desc_masks() into all_desc_masks() and init_desc_masks().
Also use CPUMASK_OFFSTACK in alloc_desc_masks().
[ Impact: fix smp_affinity copying/setup when moving irq_desc between CPUs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <49F6546E.3040406@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When requesting an IRQ, the DEBUG_SHIRQ code executes a fake IRQ just to make
sure the driver is ready to receive an IRQ immediately. The problem was that
this fake IRQ was being executed even if interrupt line failed to be allocated
by __setup_irq.
Signed-off-by: Luis Henriques <henrix@sapo.pt>
LKML-Reference: <20090401170635.GA4392@hades.domain.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ fixed bug pointed out by a warning reported by Stephen Rothwell ]
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
Create a sub directory in include/trace called events to keep the
trace point headers in their own separate directory. Only headers that
declare trace points should be defined in this directory.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch lowers the number of places a developer must modify to add
new tracepoints. The current method to add a new tracepoint
into an existing system is to write the trace point macro in the
trace header with one of the macros TRACE_EVENT, TRACE_FORMAT or
DECLARE_TRACE, then they must add the same named item into the C file
with the macro DEFINE_TRACE(name) and then add the trace point.
This change cuts out the needing to add the DEFINE_TRACE(name).
Every file that uses the tracepoint must still include the trace/<type>.h
file, but the one C file must also add a define before the including
of that file.
#define CREATE_TRACE_POINTS
#include <trace/mytrace.h>
This will cause the trace/mytrace.h file to also produce the C code
necessary to implement the trace point.
Note, if more than one trace/<type>.h is used to create the C code
it is best to list them all together.
#define CREATE_TRACE_POINTS
#include <trace/foo.h>
#include <trace/bar.h>
#include <trace/fido.h>
Thanks to Mathieu Desnoyers and Christoph Hellwig for coming up with
the cleaner solution of the define above the includes over my first
design to have the C code include a "special" header.
This patch converts sched, irq and lockdep and skb to use this new
method.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As discussed in the thread here:
http://marc.info/?l=linux-kernel&m=123964468521142&w=2
Eric W. Biederman observed:
> It looks like some additional bugs have slipped in since last I looked.
>
> set_irq_affinity does this:
> ifdef CONFIG_GENERIC_PENDING_IRQ
> if (desc->status & IRQ_MOVE_PCNTXT || desc->status & IRQ_DISABLED) {
> cpumask_copy(desc->affinity, cpumask);
> desc->chip->set_affinity(irq, cpumask);
> } else {
> desc->status |= IRQ_MOVE_PENDING;
> cpumask_copy(desc->pending_mask, cpumask);
> }
> #else
>
> That IRQ_DISABLED case is a software state and as such it has nothing to
> do with how safe it is to move an irq in process context.
[...]
>
> The only reason we migrate MSIs in interrupt context today is that there
> wasn't infrastructure for support migration both in interrupt context
> and outside of it.
Yes. The idea here was to force the MSI migration to happen in process
context. One of the patches in the series did
disable_irq(dev->irq);
irq_set_affinity(dev->irq, cpumask_of(dev->cpu));
enable_irq(dev->irq);
with the above patch adding irq/manage code check for interrupt disabled
and moving the interrupt in process context.
IIRC, there was no IRQ_MOVE_PCNTXT when we were developing this HPET
code and we ended up having this ugly hack. IRQ_MOVE_PCNTXT was there
when we eventually submitted the patch upstream. But, looks like I did a
blind rebasing instead of using IRQ_MOVE_PCNTXT in hpet MSI code.
Below patch fixes this. i.e., revert commit 932775a4ab
and add PCNTXT to HPET MSI setup. Also removes copying of desc->affinity
in generic code as set_affinity routines are doing it internally.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Li Shaohua" <shaohua.li@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: "lcm@us.ibm.com" <lcm@us.ibm.com>
Cc: suresh.b.siddha@intel.com
LKML-Reference: <20090413222058.GB8211@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Need to free the old cpumask for affinity and pending_mask.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49D18FF0.50707@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce helper functions allowing us to prevent device drivers from
getting any interrupts (without disabling interrupts on the CPU)
during suspend (or hibernation) and to make them start to receive
interrupts again during the subsequent resume. These functions make it
possible to keep timer interrupts enabled while the "late" suspend and
"early" resume callbacks provided by device drivers are being
executed. In turn, this allows device drivers' "late" suspend and
"early" resume callbacks to sleep, execute ACPI callbacks etc.
The functions introduced here will be used to rework the handling of
interrupts during suspend (hibernation) and resume. Namely,
interrupts will only be disabled on the CPU right before suspending
sysdevs, while device drivers will be prevented from receiving
interrupts, with the help of the new helper function, before their
"late" suspend callbacks run (and analogously during resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Delta patch to address the review comments.
- Implement warning when IRQ_WAKE_THREAD is requested and no
thread handler installed
- coding style fixes
Pointed-out-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some devices use devres_request_irq() for to install their interrupt
handler. Add support for threaded interrupts to devres as well.
[tglx - simplified and adapted to latest threadirq version]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for threaded interrupt handlers:
A device driver can request that its main interrupt handler runs in a
thread. To achive this the device driver requests the interrupt with
request_threaded_irq() and provides additionally to the handler a
thread function. The handler function is called in hard interrupt
context and needs to check whether the interrupt originated from the
device. If the interrupt originated from the device then the handler
can either return IRQ_HANDLED or IRQ_WAKE_THREAD. IRQ_HANDLED is
returned when no further action is required. IRQ_WAKE_THREAD causes
the genirq code to invoke the threaded (main) handler. When
IRQ_WAKE_THREAD is returned handler must have disabled the interrupt
on the device level. This is mandatory for shared interrupt handlers,
but we need to do it as well for obscure x86 hardware where disabling
an interrupt on the IO_APIC level redirects the interrupt to the
legacy PIC interrupt lines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Two years migration time is enough. Remove the compability cruft.
Add the deprecated warning in kernel/irq/handle.c because marking
__do_IRQ itself is way too noisy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: cleanup
The code is only compiled if CONFIG_GENERIC_HARDIRQS=y so another
check for this define in the code is redundant. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export the setup_irq() and remove_irq() symbols.
I'd like to export these functions since I have timer
code that needs to use setup_irq() early on (too early
for request_irq()), and the same code can also be
compiled as a module.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120559.2926.82371.sendpatchset@rx1.opensource.se>
[ changed to _GPL as these are special APIs deep inside the irq layer. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Modify remove_irq() to match setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120551.2926.43942.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new API
This patch adds a remove_irq() function for releasing
interrupts requested with setup_irq().
Without this patch we have no way of releasing such
interrupts since free_irq() today tries to kfree()
the irqaction passed with setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120542.2926.56609.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sure the genirq layer handlers are indeed running handlers
in hardirq context. That is the genirq expectation and doing
anything else is broken.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1236006812.5330.632.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new tracepoints
Add them to the generic IRQ code, that way every architecture
gets these new tracepoints, not just x86.
Using Steve's new 'TRACE_FORMAT', I can get function graph
trace as follows using the original two IRQ tracepoints:
3) | handle_IRQ_event() {
3) | /* (irq_handler_entry) irq=28 handler=eth0 */
3) | e1000_intr_msi() {
3) 2.460 us | __napi_schedule();
3) 9.416 us | }
3) | /* (irq_handler_exit) irq=28 handler=eth0 return=handled */
3) + 22.935 us | }
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
'p' stands for pointer - make it clear in setup_irq() and free_irq()
what kind of pointer it is.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus noticed that the 'pp' variable can be eliminated
altogether, and the loop can be cleaned up further.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
- separate out the loop from the actual freeing logic, this wins us
two indentation levels allowing a number of followup prettifications
- turn the WARN_ON() into a more informative WARN().
- clean up the comments and the code flow some more
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
request_irq() calls into proc code via __setup_irq() which is not safe
in an atomic context, so request_irq() can itself use the more
reliable GFP_KERNEL allocation for the action descriptor.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While being at it make every occurrence of 'do_irq_select_affinity'
have the same signature in terms of signedness of the first argument.
Fix this sparse warning:
kernel/irq/manage.c:112:5: warning: symbol 'do_irq_select_affinity' was not declared. Should it be static?
Also rename do_irq_select_affinity() to setup_affinity() - shorter name
and clearer naming.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify and make init_kstat_irqs etc more type proof, suggested by
Andrew.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: get correct kstat_irqs [/proc/interrupts] for msi/msi-x etc
need to call clear_kstat_irqs(), so when we reuse that irq_desc,
we get correct kstat in /proc/interrupts.
This makes /proc/interrupts not have <NULL> entries.
Don't need to worry about arch that doesn't support genirq, because they
will not call dynamic_irq_cleanup().
v2: simplify and make clear_kstat_irqs more robust
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Eric Paris reported:
> I have an hp dl785g5 which is unable to successfully run
> 2.6.29-0.66.rc3.fc11.x86_64 or 2.6.29-rc2-next-20090126. During bootup
> (early in userspace daemons starting) I get the below BUG, which quickly
> renders the machine dead. I assume it is because sparse_irq_lock never
> gets released when the BUG kills that task.
Adjust lock sequence when migrating a descriptor with
CONFIG_NUMA_MIGRATE_IRQ_DESC enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the initialization of irq_default_affinity to early_irq_init as
core_initcall is too late.
irq_default_affinity can be used in init_IRQ and potentially timer and
SMP init as well. All of these happen before core_initcall. Moving
the initialization to early_irq_init ensures that it is initialized
before it is used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Mike Travis <travis@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In interrupt.h these functions are declared only if
CONFIG_GENERIC_HARDIRQS is set. We should define them under identical
conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a shared interrupt debug facility under CONFIG_DEBUG_SHIRQ:
it uses the existing irqpoll facilities to iterate through all
registered interrupt handlers and call those which can handle shared
IRQ lines.
This can be handy for suspend/resume debugging: if we call this function
early during resume we can trigger crashes in those drivers which have
incorrect assumptions about when exactly their ISRs will be called
during suspend/resume.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar wrote:
> All non-x86 architectures fail to build:
>
> In file included from /home/mingo/tip/include/linux/random.h:11,
> from /home/mingo/tip/include/linux/stackprotector.h:6,
> from /home/mingo/tip/init/main.c:17:
> /home/mingo/tip/include/linux/irqnr.h:26:63: error: asm/irq_vectors.h: No such file or directory
Do not include asm/irq_vectors.h in generic code - it's not available
on all architectures.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce memory usage.
Allocate kstat_irqs_legacy based on nr_cpu_ids to deal with this
memory usage bump when NR_CPUS bumped from 128 to 4096:
8192 +253952 262144 +3100% kstat_irqs_legacy(.bss)
This is only when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: Reduce memory usage.
This is the second half of the changes to make the irq_desc_ptrs be
variable sized based on nr_cpu_ids. This is done by adding a new
"max_nr_irqs" macro to irq_vectors.h (and a dummy in irqnr.h) to
return a max NR_IRQS value based on NR_CPUS or nr_cpu_ids.
This necessitated moving the define of MAX_IO_APICS to a separate
file (asm/apicnum.h) so it could be included without the baggage
of the other asm/apicdef.h declarations.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: allocate irq_desc_ptrs in preparation for making it variable-sized.
This addresses this memory usage bump when NR_CPUS bumped from 128 to 4096:
34816 +229376 264192 +658% irq_desc_ptrs(.data.read_mostly)
The patch is split into two parts, the first simply allocates the
irq_desc_ptrs array. Then next will deal with making it variable.
This is only when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: cleanup WARN msg.
Ingo requested:
> While at it, could you please also convert this to a WARN() construct
> instead? (in a separate commit)
... and it shall be done. ;-)
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: preparation, cleanup, add KERN_INFO printk
Modify references from NR_IRQS to nr_irqs as the later will become
variable-sized based on nr_cpu_ids when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: fix bug where new irq_desc uses old cpumask pointers which are freed.
As Yinghai pointed out, init_copy_one_irq_desc() copies the old desc to
the new desc overwriting the cpumask pointers. Since the old_desc and
the cpumask pointers are freed, then memory corruption will occur if
these old pointers are used.
Move the allocation of these pointers to after the copy.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Impact: reduce memory usage, use new cpumask API.
Replace the affinity and pending_masks with cpumask_var_t's. This adds
to the significant size reduction done with the SPARSE_IRQS changes.
The added functions (init_alloc_desc_masks & init_copy_desc_masks) are
in the include file so they can be inlined (and optimized out for the
!CONFIG_CPUMASKS_OFFSTACK case.) [Naming chosen to be consistent with
the other init*irq functions, as well as the backwards arg declaration
of "from, to" instead of the more common "to, from" standard.]
Includes a slight change to the declaration of struct irq_desc to embed
the pending_mask within ifdef(CONFIG_SMP) to be consistent with other
references, and some small changes to Xen.
Tested: sparse/non-sparse/cpumask_offstack/non-cpumask_offstack/nonuma/nosmp on x86_64
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: virtualization@lists.osdl.org
Cc: xen-devel@lists.xensource.com
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Impact: clean up sparseirq fallout on random.c
Ingo suggested to change some ifdef from SPARSE_IRQ to GENERIC_HARDIRQS
so we could some #ifdef later if all arch support genirq
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Right now, most of the kernel boot is strictly synchronous, such that
various hardware delays are done sequentially.
In order to make the kernel boot faster, this patch introduces
infrastructure to allow doing some of the initialization steps
asynchronously, which will hide significant portions of the hardware delays
in practice.
In order to not change device order and other similar observables, this
patch does NOT do full parallel initialization.
Rather, it operates more in the way an out of order CPU does; the work may
be done out of order and asynchronous, but the observable effects
(instruction retiring for the CPU) are still done in the original sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
Impact: build fix on ia64
ia64's default_affinity_write() still had old cpumask_t usage:
/home/mingo/tip/kernel/irq/proc.c: In function `default_affinity_write':
/home/mingo/tip/kernel/irq/proc.c:114: error: incompatible type for argument 1 of `is_affinity_mask_valid'
make[3]: *** [kernel/irq/proc.o] Error 1
make[3]: *** Waiting for unfinished jobs....
update it to cpumask_var_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: Reduce stack usage, use new cpumask API. ALPHA mod!
Main change is that irq_default_affinity becomes a cpumask_var_t, so
treat it as a pointer (this effects alpha).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'irq-fixes-for-linus-4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparseirq: move __weak symbols into separate compilation unit
sparseirq: work around __weak alias bug
sparseirq: fix hang with !SPARSE_IRQ
sparseirq: set lock_class for legacy irq when sparse_irq is selected
sparseirq: work around compiler optimizing away __weak functions
sparseirq: fix desc->lock init
sparseirq: do not printk when migrating IRQ descriptors
sparseirq: remove duplicated arch_early_irq_init()
irq: simplify for_each_irq_desc() usage
proc: remove ifdef CONFIG_SPARSE_IRQ from stat.c
irq: for_each_irq_desc() move to irqnr.h
hrtimer: remove #include <linux/irq.h>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, sparseirq: clean up Kconfig entry
x86: turn CONFIG_SPARSE_IRQ off by default
sparseirq: fix numa_migrate_irq_desc dependency and comments
sparseirq: add kernel-doc notation for new member in irq_desc, -v2
locking, irq: enclose irq_desc_lock_class in CONFIG_LOCKDEP
sparseirq, xen: make sure irq_desc is allocated for interrupts
sparseirq: fix !SMP building, #2
x86, sparseirq: move irq_desc according to smp_affinity, v7
proc: enclose desc variable of show_stat() in CONFIG_SPARSE_IRQ
sparse irqs: add irqnr.h to the user headers list
sparse irqs: handle !GENIRQ platforms
sparseirq: fix !SMP && !PCI_MSI && !HT_IRQ build
sparseirq: fix Alpha build failure
sparseirq: fix typo in !CONFIG_IO_APIC case
x86, MSI: pass irq_cfg and irq_desc
x86: MSI start irq numbering from nr_irqs_gsi
x86: use NR_IRQS_LEGACY
sparse irq_desc[] array: core kernel and x86 changes
genirq: record IRQ_LEVEL in irq_desc[]
irq.h: remove padding from irq_desc on 64bits
Impact: fix theoretical NULL dereference
The generic irq layer doesn't know whether irq_chip has ack routine on some
architectures or not. Upon that, before calling chip->ack, we should check
that it's not NULL.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
GCC has a bug with __weak alias functions: if the functions are in
the same compilation unit as their call site, GCC can decide to
inline them - and thus rob the linker of the opportunity to override
the weak alias with the real thing.
So move all the IRQ handling related __weak symbols to kernel/irq/chip.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot crash if the kernel is built with certain GCC versions
GCC has a bug with __weak alias functions: if the functions are in
the same compilation unit as their call site, GCC can decide to
inline them - and thus rob the linker of the opportunity to override
the weak alias with the real thing.
This can lead to the boot crash reported by Kamalesh Babulal:
ACPI: Core revision 20080926
Setting APIC routing to flat
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
IP: [<ffffffff8021f9a8>] add_pin_to_irq_cpu+0x14/0x74
PGD 0
Oops: 0000 [#1] SMP
[...]
So move the arch_init_chip_data() function from handle.c to manage.c.
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix hang
Suresh report his two sockets system only works with SPARSE_IRQ enable
it turns out we miss the setting desc->irq
so provide early_irq_init() even !SPARSE_IRQ to set desc->irq
Reported-by: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add lockdep annotation to legacy IRQ descs
Warnings resulting out of this were not seen in practice, but it's prudent
to initialize the legacy descriptors to the lock class as well, symmetric
to how we do it with other descriptors.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix panic on null pointer with sparseirq
Some GCC versions seem to inline the weak global function,
when that function is empty.
Work it around, by making the functions return a (dummy) integer.
Signed-off-by: Yinghai <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
init_one_irq_desc() does not initialize the desc->lock properly -
you cannot init a lock by memcpying some other lock on it.
This happens to work right now (because irq_desc_init is never in use),
but it's a dangerous construct nevertheless, so fix it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
