I have submitted the patch for x86_64, this is submission for i386.
The patch changes the way IRQs are handed out to PCI devices. Currently,
each I/O APIC pin gets associated with an IRQ, no matter if the pin is used
or not. This imposes severe limitation on systems that have designs that
employ many I/O APICs, only utilizing couple lines of each, such as P64H2
chipset. It is used in ES7000, and currently, there is no way to boot the
system with more that 9 I/O APICs.
The simple change below allows to boot a system with say 64 (or more) I/O
APICs, each providing 1 slot, which otherwise impossible because of the IRQ
gaps created for unused lines on each I/O APIC. It does not resolve the
problem with number of devices that exceeds number of possible IRQs, but
eases up a tension for IRQs on any large system with potentually large
number of devices.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the timer frequency selectable. The timer interrupt may cause bus
and memory contention in large NUMA systems since the interrupt occurs
on each processor HZ times per second.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Get the i386 watchdog tick calculation into a state where it can also be used
on CPUs with frequencies beyond 4GHz, and it consolidates the calculation into
a single place (for potential furture adjustments).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is per Andi's request to remove NO_IOAPIC_CHECK from genapic and
use heuristics to prevent unique I/O APIC ID check for systems that don't
need it. The patch disables unique I/O APIC ID check for Xeon-based and
other platforms that don't use serial APIC bus for interrupt delivery.
Andi stated that AMD systems don't need unique IO_APIC_IDs either.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This problem was first noticed on PPC and has already been fixed there.
But the exact same issue applies to other platforms in the same way. The
signal blocking for sa_mask and the handled signal takes place after the
handler setup. When the stack is bogus, the handler setup forces a
SIGSEGV. But then this will be blocked, and returning to user mode will
fault again and iterate. This patch fixes the problem by checking whether
signal handler setup failed, and not doing the signal-blocking if so. This
copies what was done in the ppc code. I think all architectures' signal
handler setup code follows this pattern and needs the change.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Issue:
Current tsc based delay_calibration can result in significant errors in
loops_per_jiffy count when the platform events like SMIs
(System Management Interrupts that are non-maskable) are present. This could
lead to potential kernel panic(). This issue is becoming more visible with 2.6
kernel (as default HZ is 1000) and on platforms with higher SMI handling
latencies. During the boot time, SMIs are mostly used by BIOS (for things
like legacy keyboard emulation).
Description:
The psuedocode for current delay calibration with tsc based delay looks like
(0) Estimate a value for loops_per_jiffy
(1) While (loops_per_jiffy estimate is accurate enough)
(2) wait for jiffy transition (jiffy1)
(3) Note down current tsc (tsc1)
(4) loop until tsc becomes tsc1 + loops_per_jiffy
(5) check whether jiffy changed since jiffy1 or not and refine
loops_per_jiffy estimate
Consider the following cases
Case 1:
If SMIs happen between (2) and (3) above, we can end up with a
loops_per_jiffy value that is too low. This results in shorted delays and
kernel can panic () during boot (Mostly at IOAPIC timer initialization
timer_irq_works() as we don't have enough timer interrupts in a specified
interval).
Case 2:
If SMIs happen between (3) and (4) above, then we can end up with a
loops_per_jiffy value that is too high. And with current i386 code, too
high lpj value (greater than 17M) can result in a overflow in
delay.c:__const_udelay() again resulting in shorter delay and panic().
Solution:
The patch below makes the calibration routine aware of asynchronous events
like SMIs. We increase the delay calibration time and also identify any
significant errors (greater than 12.5%) in the calibration and notify it to
user.
Patch below changes both i386 and x86-64 architectures to use this
new and improved calibrate_delay_direct() routine.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch causes the various arch specific install.sh scripts to
look for ${CROSS_COMPILE}installkernel rather than just installkernel (in
both /sbin/ and ~/bin/ where the script already did this). This allows you
to have e.g. arm-linux-installkernel as a handy way to install on your
cross target. It also prevents the script picking up on the host
/sbin/installkernel which causes the script to fall through and do the
install itself (which is what I actually use myself, with $INSTALL_PATH
set).
I don't believe it causes back-compatibility problems since calling the
host installkernel was never likely to work or be what you wanted when
cross compiling anyway. If $CROSS_COMPILE isn't set then nothing changes.
I only use ARM and i386 myself but I figured it couldn't hurt to do the
whole lot. I've cc'd those who I hope are the arch maintainers for files
that I've touched.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the i386 architecture to be built on a system with a biarch
compiler that defaults to x86-64, merely by specifying ARCH=i386.
As previously discussed, this uses the equivalent logic to the ppc port.
Signed-Off-By: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This helps a lot when debugging out of memory stuff - useful especially to
see if all the memory is sucked into slab, etc.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide the architecture specific implementation for SPARSEMEM for i386 SMP
and NUMA systems.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of
mem_map[] is needed by discontiguous memory machines (like in the old
CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem
replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually
become a complete replacement.
A significant advantage over DISCONTIGMEM is that it's completely separated
from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA
and DISCONTIG are often confused.
Another advantage is that sparse doesn't require each NUMA node's ranges to be
contiguous. It can handle overlapping ranges between nodes with no problems,
where DISCONTIGMEM currently throws away that memory.
Sparsemem uses an array to provide different pfn_to_page() translations for
each SECTION_SIZE area of physical memory. This is what allows the mem_map[]
to be chopped up.
In order to do quick pfn_to_page() operations, the section number of the page
is encoded in page->flags. Part of the sparsemem infrastructure enables
sharing of these bits more dynamically (at compile-time) between the
page_zone() and sparsemem operations. However, on 32-bit architectures, the
number of bits is quite limited, and may require growing the size of the
page->flags type in certain conditions. Several things might force this to
occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of
memory), an increase in the physical address space, or an increase in the
number of used page->flags.
One thing to note is that, once sparsemem is present, the NUMA node
information no longer needs to be stored in the page->flags. It might provide
speed increases on certain platforms and will be stored there if there is
room. But, if out of room, an alternate (theoretically slower) mechanism is
used.
This patch introduces CONFIG_FLATMEM. It is used in almost all cases where
there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM
often have to compile out the same areas of code.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow architectures to indicate that they will be providing hooks to indice
installed memory areas, memory_present(). Provide prototypes for the i386
implementation.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a default implementation for early_pfn_to_nid returning node 0. Allow
architectures to override this with their own implementation out of
asm/mmzone.h.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For all architectures, this just means that you'll see a "Memory Model"
choice in your architecture menu. For those that implement DISCONTIGMEM,
you may eventually want to make your ARCH_DISCONTIGMEM_ENABLE a "def_bool
y" and make your users select DISCONTIGMEM right out of the new choice
menu. The only disadvantage might be if you have some specific things that
you need in your help option to explain something about DISCONTIGMEM.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
discontig.c has some assumptions that mem_map[]s inside of a node are
contiguous. Teach it to make sure that each region that it's bringing online
is actually made up of valid ranges of ram.
Written-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a simple allocator for the NUMA remap space. This space is very
scarce, used for structures which are best allocated node local.
This mechanism is also used on non-NUMA ia64 systems with a vmem_map to keep
the pgdat->node_mem_map initialized in a consistent place for all
architectures.
Issues:
o alloc_remap takes a node_id where we might expect a pgdat which was intended
to allow us to allocate the pgdat's using this mechanism; which we do not yet
do. Could have alloc_remap_node() and alloc_remap_nid() for this purpose.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following four patches provide the last needed changes before the
introduction of sparsemem. For a more complete description of what this
will do, please see this patch:
http://www.sr71.net/patches/2.6.11/2.6.11-bk7-mhp1/broken-out/B-sparse-150-sparsemem.patch
or previous posts on the subject:
http://marc.theaimsgroup.com/?t=110868540700001&r=1&w=2http://marc.theaimsgroup.com/?l=linux-mm&m=109897373315016&w=2
Three of these are i386-only, but one of them reorganizes the macros
used to manage the space in page->flags, and will affect all platforms.
There are analogous patches to the i386 ones for ppc64, ia64, and
x86_64, but those will be submitted by the normal arch maintainers.
The combination of the four patches has been test-booted on a variety of
i386 hardware, and compiled for ppc64, i386, and x86-64 with about 17
different .configs. It's also been runtime-tested on ia64 configs (with
more patches on top).
This patch:
We _know_ which node pages in general belong to, at least at a very gross
level in node_{start,end}_pfn[]. Use those to target the allocations of
pages.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I am always trying to make sure I've booted the right kernel after a new
install. Too paranoid maybe. But I guess there're other people like me.
So let's make kbuild display the compile version number at the end to give
us a hint. I know we may be booting vmlinux someday, but don't care about
it for now.
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove PG_highmem, to save a page flag. Use is_highmem() instead. It'll
generate a little more code, but we don't use PageHigheMem() in many places.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ingo recently introduced a great speedup for allocating new mmaps using the
free_area_cache pointer which boosts the specweb SSL benchmark by 4-5% and
causes huge performance increases in thread creation.
The downside of this patch is that it does lead to fragmentation in the
mmap-ed areas (visible via /proc/self/maps), such that some applications
that work fine under 2.4 kernels quickly run out of memory on any 2.6
kernel.
The problem is twofold:
1) the free_area_cache is used to continue a search for memory where
the last search ended. Before the change new areas were always
searched from the base address on.
So now new small areas are cluttering holes of all sizes
throughout the whole mmap-able region whereas before small holes
tended to close holes near the base leaving holes far from the base
large and available for larger requests.
2) the free_area_cache also is set to the location of the last
munmap-ed area so in scenarios where we allocate e.g. five regions of
1K each, then free regions 4 2 3 in this order the next request for 1K
will be placed in the position of the old region 3, whereas before we
appended it to the still active region 1, placing it at the location
of the old region 2. Before we had 1 free region of 2K, now we only
get two free regions of 1K -> fragmentation.
The patch addresses thes issues by introducing yet another cache descriptor
cached_hole_size that contains the largest known hole size below the
current free_area_cache. If a new request comes in the size is compared
against the cached_hole_size and if the request can be filled with a hole
below free_area_cache the search is started from the base instead.
The results look promising: Whereas 2.6.12-rc4 fragments quickly and my
(earlier posted) leakme.c test program terminates after 50000+ iterations
with 96 distinct and fragmented maps in /proc/self/maps it performs nicely
(as expected) with thread creation, Ingo's test_str02 with 20000 threads
requires 0.7s system time.
Taking out Ingo's patch (un-patch available per request) by basically
deleting all mentions of free_area_cache from the kernel and starting the
search for new memory always at the respective bases we observe: leakme
terminates successfully with 11 distinctive hardly fragmented areas in
/proc/self/maps but thread creating is gringdingly slow: 30+s(!) system
time for Ingo's test_str02 with 20000 threads.
Now - drumroll ;-) the appended patch works fine with leakme: it ends with
only 7 distinct areas in /proc/self/maps and also thread creation seems
sufficiently fast with 0.71s for 20000 threads.
Signed-off-by: Wolfgang Wander <wwc@rentec.com>
Credit-to: "Richard Purdie" <rpurdie@rpsys.net>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu> (partly)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of the code in arch/*/mm/hugetlbpage.c is quite similar. This patch
attempts to consolidate a lot of the code across the arch's, putting the
combined version in mm/hugetlb.c. There are a couple of uglyish hacks in
order to covert all the hugepage archs, but the result is a very large
reduction in the total amount of code. It also means things like hugepage
lazy allocation could be implemented in one place, instead of six.
Tested, at least a little, on ppc64, i386 and x86_64.
Notes:
- this patch changes the meaning of set_huge_pte() to be more
analagous to set_pte()
- does SH4 need s special huge_ptep_get_and_clear()??
Acked-by: William Lee Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the (much simplified) early reclaim. The goal of this
patch is to reclaim some easily-freed pages from a zone before falling back
onto another zone.
One of the major uses of this is NUMA machines. With the default allocator
behavior the allocator would look for memory in another zone, which might be
off-node, before trying to reclaim from the current zone.
This adds a zone tuneable to enable early zone reclaim. It is selected on a
per-zone basis and is turned on/off via syscall.
Adding some extra throttling on the reclaim was also required (patch
4/4). Without the machine would grind to a crawl when doing a "make -j"
kernel build. Even with this patch the System Time is higher on
average, but it seems tolerable. Here are some numbers for kernbench
runs on a 2-node, 4cpu, 8Gig RAM Altix in the "make -j" run:
wall user sys %cpu ctx sw. sleeps
---- ---- --- ---- ------ ------
No patch 1009 1384 847 258 298170 504402
w/patch, no reclaim 880 1376 667 288 254064 396745
w/patch & reclaim 1079 1385 926 252 291625 548873
These numbers are the average of 2 runs of 3 "make -j" runs done right
after system boot. Run-to-run variability for "make -j" is huge, so
these numbers aren't terribly useful except to seee that with reclaim
the benchmark still finishes in a reasonable amount of time.
I also looked at the NUMA hit/miss stats for the "make -j" runs and the
reclaim doesn't make any difference when the machine is thrashing away.
Doing a "make -j8" on a single node that is filled with page cache pages
takes 700 seconds with reclaim turned on and 735 seconds without reclaim
(due to remote memory accesses).
The simple zone_reclaim syscall program is at
http://www.bork.org/~mort/sgi/zone_reclaim.c
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch causes the ignore_normal_resume flag to be set slightly earlier,
before there is a chance that the apm driver will receive the normal resume
event from the BIOS. (Addresses Debian bug #310865)
Signed-off-by: Thomas Hood <jdthood@yahoo.co.uk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/i386/kernel/vsyscall-note.o is not listed as a target so its .cmd file
is neither considered as a target nor is it read on the next build. This
causes vsyscall-note.o to be rebuilt every time that you run make, which
causes vmlinux to be rebuilt every time.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As mandated by the spec, disable timer around transitions.
From code by : Ken Staton <ken_staton@agilent.com
Signed-off-by: Dave Jones <davej@redhat.com>
The spec states that we have to do this, which is *horrid*.
Based on code from: Ken Staton <ken_staton@agilent.com>
Signed-off-by: Dave Jones <davej@redhat.com>
With the release of the dual-core AMD Opterons last week,
it's high time that cpufreq supported them. The attached
patch applies cleanly to 2.6.12-rc3 and updates powernow-k8
to support the latest Athlon 64 and Opteron processors.
Update the driver to version 1.40.0 and provide support
for dual-core processors.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Some cpufreq drivers (at that time, only powernow-k7) need to recalibrate the
cpu_khz at runtime.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
We have to recalibrate cpu_khz in order to use the current FID instead the max
FID since some BIOS do not put the processor at maximum frequency at POST.
Also, some BIOS will change the processor frequency at our back after cpu_khz
was calibrate. Finally, this will fix a long standing bug when we do
something like this:
# rmmod powernow-k7
# modprobe powernow-k7
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The speedstep-smi driver actually works on >=1 notebook with a
Pentium 4-M CPU where all other cpufreq drivers fail. Therefore,
allow speedstep-smi on P4Ms again, but warn users of likely failure
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The Pentium 4 - Ms (HT) with CPUID 0xF34 and 0xF41 seem to support
centrino-like enhanced speedstep; however, no "table" support is possible.
Therefore, put NULL entries into speedstep-centrino.c
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
This is a neverending story
linux/acpi.h contains empty declarations for acpi_boot_init() &
acpi_boot_table_init() but they are nested inside #ifdef CONFIG_ACPI.
So we'll have to #ifdef in arch/i386/kernel/setup.c: setup_arch()
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes 'smp_num_siblings' value on the systems with a buggy bios,
which sets number of siblings to '2' even when HT is disabled. (more
details are at http://bugzilla.kernel.org/show_bug.cgi?id=4359)
I am planning to do more cleanup in this area (like moving smp_num_siblings
to per cpuinfo) shortly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
num_cache_leaves is used in __devexit cache_remove_dev() and can therefore
not be __devinit.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even after the previous fix you can still set CONFIG_ACPI_BOOT
indirectly even without CONFIG_ACPI by choosing CONFIG_PCI and
CONFIG_PCI_MMCONFIG.
That doesn't build very well either.
This makes PCI_MMCONFIG depend on ACPI, fixing that hole.
[ I guess in theory Kconfig could follow the whole chain of dependencies
for things that get selected, but that sounds insanely complicated, so
we'll just fix up these things by hand. --Linus ]
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete quirk_via_bridge(), restore quirk_via_irqpic() -- but now
improved to be invoked upon device ENABLE, and now only for VIA devices
-- not all devices behind VIA bridges.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a compile bug by moving a static inline function to the
right place. The body of a static inline function has to be declared
before the use of this function.
Signed-off-by: Dominik Hackl <dominik@hackl.dhs.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold the vmlist_lock while doing change_page_attr, otherwise we
could reset someone else's mapping.
Requires previous patch to add __remove_vm_area
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove duplicated ifdef
- Make core_id match what Intel uses
- Initialize phys_proc_id correctly for non DC case
- Handle non power of two core numbers.
Fixes for both i386 and x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The GET_INDEX() macro should use just the low three bits of the devfn,
otherwise we have a memory scribble in pcie_rootport_aspm_quirk that
overwrites ptype_all
Fix it to be more careful about its arguments while at it.
Acked by Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Last round hopefully of cpu_core_id changes hopefully fow now:
- Always initialize cpu_core_id for all CPUs, even when no dual core setup
is detected. This prevents funny /proc/cpuinfo output
- Do the same with phys_proc_id[] even when no HyperThreading - dito.
- Use the CPU APIC-ID from CPUID 1 instead of the linux virtual CPU number
to identify the core for AMD dual core setups.
Patch for i386/x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Changed Name/defines from "Geode GX" to "Geode GX1" for clarification
- Dropped "-march=i586" in favor of "-march=i486"
- Dopped X86_OOSTORE support for Geode GX1
Signed-off-by: Kianusch Sayah Karadji <kianusch@sk-tech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When I do a "diff -Nur arch/i386 arch/x86_64" to see what is different between these two
architectures, I see some differences due to whitespace issues only. The attached patch removes
some of the noise by fixing up the following files:
- arch/i386/boot/bootsect.S
- arch/i386/boot/video.S
- arch/x86_64/boot/bootsect.S
Signed-off-by: Daniel Dickman <didickman@yahoo.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kprobes could not handle the insertion of a probe on the ret/lret
instruction and used to oops after single stepping since kprobes was
modifying eip/rip incorrectly. Adjustment of eip/rip is not required after
single stepping in case of ret/lret instruction, because eip/rip points to
the correct location after execution of the ret/lret instruction. This
patch fixes the above problem.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In include/asm-x86_64/string.h there are such comments:
/* Use C out of line version for memcmp */
#define memcmp __builtin_memcmp
int memcmp(const void * cs,const void * ct,size_t count);
This would mean that if the compiler does not decide to use __builtin_memcmp,
it emits a call to memcmp to be satisfied by the C out-of-line version in
lib/string.c. What happens is that after preprocessing, in lib/string.i you
may find the definition of "__builtin_strcmp".
Actually, by accident, in the object you will find the definition of strcmp
and such (maybe a trick intended to redirect calls to __builtin_memcmp to the
default memcmp when the definition is not expanded); however, this particular
case is not a documented feature as far as I can see.
Also, the EXPORT_SYMBOL does not work, so it's duplicated in the arch.
I simply added some #undef to lib/string.c and removed the (now duplicated)
exports in x86-64 and UML/x86_64 subarchs (the second ones are introduced by
another patch I just posted for -mm).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent change fix-crash-in-entrys-restore_all.patch
childregs->esp = esp;
p->thread.esp = (unsigned long) childregs;
- p->thread.esp0 = (unsigned long) (childregs+1);
+ p->thread.esp0 = (unsigned long) (childregs+1) - 8;
p->thread.eip = (unsigned long) ret_from_fork;
introduces an inconsistency between esp and esp0 before the task is run the
first time. esp0 is no longer the actual start of the stack, but 8 bytes
off.
This shows itself clearly in a scenario when a ptracer that is set to also
ptrace eventual children traces program1 which then clones thread1. Now
the ptracer wants to modify the registers of thread1. The x86 ptrace
implementation bases it's knowledge about saved user-space registers upon
p->thread.esp0. But this will be a few bytes off causing certain writes to
the kernel stack to overwrite a saved kernel function address making the
kernel when actually running thread1 jump out into user-space. Very
spectacular.
The testcase I've used is:
/* start with strace -f ./a.out */
#include <pthread.h>
#include <stdio.h>
void *do_thread(void *p)
{
for (;;);
}
int main()
{
pthread_t one;
pthread_create(&one, NULL, &do_thread, NULL);
for (;;);
return 0;
}
So, my solution is to instead of just adjusting esp0 that creates an
inconsitent state I adjust where the user-space registers are saved with -8
bytes. This gives us the wanted extra bytes on the start of the stack and
esp0 is now correct. This solves the issues I saw from the original
testcase from Mateusz Berezecki and has survived testing here. I think
this should go into -mm a round or two first however as there might be some
cruft around depending on pt_regs lying on the start of the stack. That
however would have broken with the first change too!
It's actually a 2-line diff but I had to move the comment of why the -8 bytes
are there a few lines up. Thanks to Zwane for helping me with this.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of drivers use ISA DMA helpers or their equivalents for
platforms that have ISA with different DMA controller (a lot of ARM
boxen). Currently there is no way to put such dependency in Kconfig -
CONFIG_ISA is not it (e.g. it is not set on platforms that have no ISA
slots, but have on-board devices that pretend to be ISA ones).
New symbol added - ISA_DMA_API. Set when we have functional
enable_dma()/set_dma_mode()/etc. set of helpers. Next patches in the
series will add missing dependencies for drivers that need them.
I'm very carefully staying the hell out of the recurring flamefest on
what exactly CONFIG_ISA would mean in ideal world - added symbol has a
well-defined meaning and for now I really want to treat it as completely
independent from the mess around CONFIG_ISA.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another large rollup of various patches from Adrian which make things static
where they were needlessly exported.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the current code that uses _NSIG directly to instead use
valid_signal(). This avoids gcc -W warnings and off-by-one errors.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were still a few comments left refering to verify_area, and two
functions, verify_area_skas & verify_area_tt that just wrap corresponding
access_ok_skas & access_ok_tt functions, just like verify_area does for
access_ok - deprecate those.
There was also a few places that still used verify_area in commented-out
code, fix those up to use access_ok.
After applying this one there should not be anything left but finally
removing verify_area completely, which will happen after a kernel release
or two.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange for all kernel printks to be no-ops. Only available if
CONFIG_EMBEDDED.
This patch saves about 375k on my laptop config and nearly 100k on minimal
configs.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Split the i386 entry.S files into entry.S and syscall_table.S which is
included in the previous one (so actually there is no difference between them)
and use the syscall_table.S in the UML build, instead of tracking by hand the
syscall table changes (which is inherently error-prone).
We must only insert the right #defines to inject the changes we need from the
i386 syscall table (for instance some different function names); also, we
don't implement some i386 syscalls, as ioperm(), nor some TLS-related ones
(yet to provide).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch solves VM86 interrupt emulation deadlock on SMP systems. The VM86
interrupt emulation has been heavily tested and works well on UP systems
after last update, but it seems to deadlock when we have used it on SMP/HT
boxes now.
It seems, that disable_irq() cannot be called from interrupts, because it
waits until disabled interrupt handler finishes
(/kernel/irq/manage.c:synchronize_irq():while(IRQ_INPROGRESS);). This
blocks one CPU after another. Solved by use disable_irq_nosync.
There is the second problem. If IRQ source is fast, it is possible, that
interrupt is sometimes processed and re-enabled by the second CPU, before
it is disabled by the first one, but negative IRQ disable depths are not
allowed. The spinlocking and disabling IRQs over call to
disable_irq_nosync/enable_irq is the only solution found reliable till now.
Signed-off-by: Michal Sojka <sojkam1@control.felk.cvut.cz>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The specifications that talk about E820 map doesn't have an upper limit on
the number of e820 entries. But, today's kernel has a hard limit of 32.
With increase in memory size, we are seeing the number of E820 entries
reaching close to 32. Patch below bumps the number upto 128.
The patch changes the location of EDDBUF in zero-page (as it comes after E820).
As, EDDBUF is not used by boot loaders, this patch should not have any effect
on bootloader-setup code interface.
Patch covers both i386 and x86-64.
Tested on:
* grub booting bzImage
* lilo booting bzImage with EDID info enabled
* pxeboot of bzImage
Side-effect:
bss increases by ~ 2K and init.data increases by ~7.5K
on all systems, due to increase in size of static arrays.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugme.osdl.org/show_bug.cgi?id=4426
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : AMD Athlon(tm) XP
stepping : 0
cpu MHz : 2204.807
<snipped>
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 mmx fxsr sse pni syscall mmxext 3dnowext 3dnow
bogomips : 4358.14
We're marking bit 0 of extended function 0x80000001 cpuid as PNI support on
AMD processors, when it actually denotes x87 FPU present. Patch for i386
and x86_64 below.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ICH7DH and ICH7-M DH DID's to the irq.c and
pci_ids.h files.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the i386 HPET code assumes the entire HPET implementation from
the spec is present. This breaks on boxes that do not implement the
optional legacy timer replacement functionality portion of the spec.
This patch, which is very similar to my x86-64 patch for the same issue,
fixes the problem allowing i386 systems that cannot use the HPET for the
timer interrupt and RTC to still use the HPET as a time source. I've
tested this patch on a system systems without HPET, with HPET but without
legacy timer replacement, as well as HPET with legacy timer replacement.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable write combining for server works LE rev > 6 per
http://www.ussg.iu.edu/hypermail/linux/kernel/0104.3/1007.html
Signed-Off-By: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_debug() and do_int3() return void.
This patch fixes the CONFIG_KPROBES variant of do_int3() to return void too
and adjusts entry.S accordingly.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch by Jaya Kumar introduces a generic infrastructure to deal with
x86 chipsets with nonstandard reset sequences, and adds support for the
Geode gx1/cs5530a chipset.
Signed-off-by: Jaya Kumar <jayalk@intworks.biz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bug against an xSeries system showed up recently noting that the
check_nmi_watchdog() test was failing.
I have been investigating it and discovered in both i386 and x86_64 the
recent change to the routine to use the cpu_callin_map has uncovered a
problem. Prior to that change, on an SMP box, the test was trivally
passing because all cpu's were found to not yet be online, but now with the
callin_map they are discovered, it goes on to test the counter and they
have not yet begun to increment, so it announces a CPU is stuck and bails
out.
On all the systems I have access to test, the announcement of failure is
also bougs... by the time you can login and check /proc/interrupts, the
NMI count is happily incrementing on all CPUs. Its just that the test is
being done too early.
I have tried moving the call to the test around a bit, and it was always
too early. I finally hit on this proposed solution, it delays the routine
via a late_initcall(), seems like the right solution to me.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new i386/x86_64 assemblers no longer accept instructions for moving
between a segment register and a 32bit memory location, i.e.,
movl (%eax),%ds
movl %ds,(%eax)
To generate instructions for moving between a segment register and a
16bit memory location without the 16bit operand size prefix, 0x66,
mov (%eax),%ds
mov %ds,(%eax)
should be used. It will work with both new and old assemblers. The
assembler starting from 2.16.90.0.1 will also support
movw (%eax),%ds
movw %ds,(%eax)
without the 0x66 prefix. I am enclosing patches for 2.4 and 2.6 kernels
here. The resulting kernel binaries should be unchanged as before, with
old and new assemblers, if gcc never generates memory access for
unsigned gsindex;
asm volatile("movl %%gs,%0" : "=g" (gsindex));
If gcc does generate memory access for the code above, the upper bits
in gsindex are undefined and the new assembler doesn't allow it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removing the dependency on vmlinux for the install target raised a few
complaints, so instead a new target i added: kernel_install.
kernel_install will install the kernel just like the ordinary install target.
The only difference is that install has a dependency on vmlinux,
kernel_install does not. Therefore kernel_install is the best choice
when accessing the kernel over a NFS mount or as another user.
kernel_install is similar to modules_install in the fact that neither does
a full kernel compile before performing the install.
In this way they are good for root use. Also added back the
dependency on vmlinux for the install target so peoples scripts are no
longer broken.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes a trap on the 'iret' that returns us to user space
cause a nice clean SIGSEGV, instead of just a hard (and silent)
exit.
That way a debugger can actually try to see what happened, and
we also properly notify everybody who might be interested about
us being gone.
This loses the error code, but tells the debugger what happened
with ILL_BADSTK in the siginfo.
We were calling ptrace_notify() after auditing the syscall and arguments,
but the debugger could have _changed_ them before the syscall was actually
invoked. Reorder the calls to fix that.
While we're touching ever call to audit_syscall_entry(), we also make it
take an extra argument: the architecture of the syscall which was made,
because some architectures allow more than one type of syscall.
Also add an explicit success/failure flag to audit_syscall_exit(), for
the benefit of architectures which return that in a condition register
rather than only returning a single register.
Change type of syscall return value to 'long' not 'int'.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch to arch/i386/kernel/cpu/amd.c relies on the variable
cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is
only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative
SMP harnesses won't have it, which is why it breaks voyager).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Once we're strict about clearing away page tables, hugetlb_prefault can assume
there are no page tables left within its range. Since the other arches
continue if !pte_none here, let i386 do the same.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent woes with some arches needing their own pgd_addr_end macro; and 4-level
clear_page_range regression since 2.6.10's clear_page_tables; and its
long-standing well-known inefficiency in searching throughout the higher-level
page tables for those few entries to clear and free: all can be blamed on
ignoring the list of vmas when we free page tables.
Replace exit_mmap's clear_page_range of the total user address space by
free_pgtables operating on the mm's vma list; unmap_region use it in the same
way, giving floor and ceiling beyond which it may not free tables. This
brings lmbench fork/exec/sh numbers back to 2.6.10 (unless preempt is enabled,
in which case latency fixes spoil unmap_vmas throughput).
Beware: the do_mmap_pgoff driver failure case must now use unmap_region
instead of zap_page_range, since a page table might have been allocated, and
can only be freed while it is touched by some vma.
Move free_pgtables from mmap.c to memory.c, where its lower levels are adapted
from the clear_page_range levels. (Most of free_pgtables' old code was
actually for a non-existent case, prev not properly set up, dating from before
hch gave us split_vma.) Pass mmu_gather** in the public interfaces, since we
might want to add latency lockdrops later; but no attempt to do so yet, going
by vma should itself reduce latency.
But what if is_hugepage_only_range? Those ia64 and ppc64 cases need careful
examination: put that off until a later patch of the series.
What of x86_64's 32bit vdso page __map_syscall32 maps outside any vma?
And the range to sparc64's flush_tlb_pgtables? It's less clear to me now that
we need to do more than is done here - every PMD_SIZE ever occupied will be
flushed, do we really have to flush every PGDIR_SIZE ever partially occupied?
A shame to complicate it unnecessarily.
Special thanks to David Miller for time spent repairing my ceilings.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hides reparent_to_init(). reparent_to_init() should only be
called by daemonize().
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy please double check especially this one.
there may be a better solution.
Fix efi section references:
remove __initdata for struct efi efi_phys
and struct efi_memory_map memmap
Error: ./arch/i386/kernel/efi.o .text refers to 000000d3 R_386_32
.init.data
Error: ./arch/i386/kernel/efi.o .text refers to 000000ff R_386_32
.init.data
efi_memmap_walk (which is not __init nor static)
accesses both efi_phys and memmap.
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Acked-by: Randy Dunlap <rddunlap@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately
that turned out not to be the case as Russel King pointed out. Here are
fixes for Documentation and common code (mainly system devices).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- broken sibling_map setup in x86_64
- grouping all the core and HT related cpuinfo fields.
We are reasonably sure that adding new cpuinfo fields after "siblings" field,
will not cause any app failure. Thats because today's /proc/cpuinfo
format is completely different on x86, x86_64 and we haven't heard of any
x86 app breakage because of this issue. Grouping these fields will
result in more or less common format on all architectures (ia64, x86 and
x86_64) and will cause less confusion.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the code greatly. Now uses the infrastructure from the Intel dual
core patch Should fix a final bug noticed by Tyan of not detecting the nodes
correctly in some corner cases.
Patch for x86-64 and i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch adds the support for Intel dual-core detection and displaying
the core related information in /proc/cpuinfo.
It adds two new fields "core id" and "cpu cores" to x86 /proc/cpuinfo and the
"core id" field for x86_64("cpu cores" field is already present in x86_64).
Number of processor cores in a die is detected using cpuid(4) and this is
documented in IA-32 Intel Architecture Software Developer's Manual (vol 2a)
(http://developer.intel.com/design/pentium4/manuals/index_new.htm#sdm_vol2a)
This patch also adds cpu_core_map similar to cpu_sibling_map.
Slightly hacked by AK.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to use the size_and_mask in set_mtrr_var_ranges(which is called
while programming MTRR's for AP's
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It doesn't make sense to only do this only for AMD K8.
This would support future CPUs with extended address spaces properly.
For i386 and x86-64
Cc: <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 genapic mechanism should be aware of machines that use physical APIC
mode regardless of how many clusters/processors are detected.
ACPI 3.0 FADT makes this determination very simple by providing a feature
flag "force_apic_physical_destination_mode" to state whether the machine
unconditionally uses physical APIC mode.
Unisys' next generation x86_64 ES7000 will need to utilize this FADT
feature flag in order to boot the x86_64 kernel in the correct APIC mode.
This patch has been tested on both x86_64 commodity and ES7000 boxes.
Signed-off-by: Jason Davis <jason.davis@unisys.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only display physical id/siblings when there are siblings or dual core.
In 2.6.11 I accidentially broke it and it was always displaying these
fields But for compatibility to all these /proc parsers around it is better
to do it in the old way again.
Noticed by Suresh Siddha
Cc: <Suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds an ELF note to the vDSO giving the LINUX_VERSION_CODE
value. Having this in the vDSO lets the dynamic linker avoid the `uname'
syscall it now always does at startup to ascertain the kernel ABI
available.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the macro loaddebug from asm-i386/suspend.h to
asm-i386/processor.h, which is the place that makes sense for it to be
defined, removes the extra copy of the same macro in
arch/i386/kernel/process.c, and makes arch/i386/kernel/signal.c use the
macro in place of its expansion.
This is a purely cosmetic cleanup for the normal i386 kernel. However, it
is handy for Xen to be able to just redefine the loaddebug macro once
instead of also changing the signal.c code.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the irq.c and pci_ids.h files.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the access-above-bottom-of-stack crash.
1. Allows to preserve the valueable optimization
2. Works for NMIs
3. Doesn't care whether or not there are more of the like instances
where the stack is left empty.
4. Seems to work for me without the crashes:)
(akpm: this is still under discussion, although I _think_ it's OK. You might
want to hold off)
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
