ASIC3 can disable the memory, so we need to wait for mfd_cell->enable
to enable the memory before we can map the SD control registers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Use an IRQF_TRIGGER_ flag in request_irq instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Added a platform driver which uses the SDHCI core.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
Fix interaction with new generic header stuff as added by:
commit 6103ec56c6
Author: Arnd Bergmann <arnd@arndb.de>
Date: Wed May 13 22:56:27 2009 +0000
asm-generic: add generic ABI headers
The problem is that asm/signal.h has been made to include asm-generic/signal.h,
but the redundant stuff from asm/signal.h has not been discarded, leading to
multiple redefinitions.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-ocores: Can add I2C devices to the bus
i2c-s3c2410: move to using platform idtable to match devices
i2c: OMAP3: Better noise suppression for fast/standard modes
i2c: OMAP2/3: Fix scll/sclh calculations
i2c: Blackfin TWI: implement I2C_FUNC_SMBUS_I2C_BLOCK functionality
i2c: Blackfin TWI: fix transfer errors with repeat start
i2c: Blackfin TWI: fix REPEAT START mode doesn't repeat
i2c: Blackfin TWI: make sure we don't end up with a CLKDIV=0
* 'docs-next' of git://git.lwn.net/linux-2.6:
Document the debugfs API
Documentation: Add "how to write a good patch summary" to SubmittingPatches
SubmittingPatches: fix typo
docs: Encourage better changelogs in the development process document
Document Reported-by in SubmittingPatches
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
make[1]: *** [drivers/net/cnic.o] Error 1
make: *** [drivers/net/cnic.o] Error 2
Caused by not including linux/module.h
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix cnic build for case of CONFIG_INET=n.
Fix cnic build for case of CONFIG_IPV6=m and CONFIG_CNIC=y.
Fixes these build errors:
cnic.c:(.text+0x236a1d): undefined reference to `ip_route_output_key'
cnic.c:(.text+0x15a8e8): undefined reference to `ip6_route_output'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The unaligned address exception handler (and others) does not scan the
fixup tables before oopsing. This is bad because it means passing a
badly aligned pointer from user space might crash the kernel.
Fix this by scanning the fixup tables in _exception(). This should
resolve the issue for unaligned addresses as well as other less common
exceptions that might be happening during a userspace access. The page
fault handler already does fixup processing.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: Frank Shew <fshew@geometrics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make sure we don't end up with an invalid CLKDIV=0 in case someone
specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shortened subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Identation got messed up when merging the current_umask changes with
the generic ACL support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Fix warnings about unitialized dquot variables by making sure
xfs_qm_vop_dqalloc touches it even when quotas are disabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/configfs:
configfs: Rework configfs_depend_item() locking and make lockdep happy
configfs: Silence lockdep on mkdir() and rmdir()
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use more NOFS allocation
dlm: connect to nodes earlier
dlm: fix use count with multiple joins
dlm: Make name input parameter of {,dlm_}new_lockspace() const
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
